Baxi Potterton 30 HE manual Fitting The Boiler, Condensate Drain see section

Page 28

Fig. 32

Pressure Relief Valve

Fig. 33

Discharge Pipe

Wall Plate

10.0 Installation

10.4Fitting The Boiler

1.Remove the sealing caps from the boiler connections.

2.Lift the boiler using the lower edges. Engage the slots at the top rear of the boiler on the wall plate (Fig. 32).

3.Insert the sealing washers between the valves and pipes on the wall plate and the boiler connections. The rubber washers must be used on the gas connection.

4. Tighten all the connections.

10.5Fitting the Pressure Relief Discharge Pipe (Fig. 33)

1.Remove the discharge pipe from the kit.

2.Determine the routing of the discharge pipe in the vicinity of the boiler. Make up as much of the pipework as is practical, including the discharge pipe supplied.

3.The pipework must be at least 15mm diameter and run continuously downwards to a discharge point outside the building. See section 6.7 for further details.

4.Utilising one of the sealing washers, connect the

discharge pipe to the adaptor and tighten the nut.

5.Complete the discharge pipework and route it to the outside discharge point.

IMPORTANT: Make all soldered joints before connecting to the pressure relief valve.

10.6Condensate Drain (see section 7.6)

1. Connect the condensate drain using the 1” BSP nut and seal supplied.

Ensure the discharge of condensate complies with any national or local regulations in force (see British Gas “Guidance Notes for the Installation of Domestic Gas Condensing Boilers”.

2.The condensate outlet terminates in a 1” BSP nut and seal for the connection of 21.5mm (3/4in) plastic overflow pipe which should generally discharge internally into the household drainage system. If this is not possible, discharge into an outside drain is acceptable.

28© Baxi Heating UK Ltd 2007

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Installation & Service Instructions Contents Installer Notification Guidelines Scheme Members onlyLegislation Important Installation, Commissioning, Service & RepairCodes of Practice, most recent version should be used Safe Manual Handling GeneralPreparation TechniqueIntroduction DescriptionOptional Extras Case Front Panel Control Box Data BadgeLayout General Layout1211 30 31 32 Central Heating Mode Fig Domestic Hot Water Mode FigFrost Protection Mode Appliance OperationTechnical Data Performa 30 HEDimensions and Fixings System Details InformationCentral Heating Circuit BypassSystem Filling and Pressurising Pressure Relief Valve FigShowers Domestic Hot Water Circuit FigHard Water Areas Location Site RequirementsClearances Figs Gas Supply Ventilation of CompartmentsElectrical Supply External termination via internal Condensate DrainPlume Displacement Kit FlueBuilt-in element such as a window frame. See BS 5440 Pt Or DoorFlue Options Horizontal FluesHorizontal Flue Systems This bend is equivalent to 1 metreVertical Flues Twin Pipe Twin & Vertical Flue SystemsMetre for each 91.5 elbow Metre for each 45 elbow 1m extension 45bend 25m 91.5bendKey Accessory Size Flue Accessories5111079 Air duct adaptor Flue Duct AdaptorFor Twin Flue Systems fit the adaptors as follows Flue Dimensions For Roof TerminalsFlue Trim Terminal Guard FigPlume Displacement Plume Displacement Kit bElbow/Plume Outlet Assembly Ring Bracket Metres 60Ø Exhaust Flue Pipe 60Ø SupportDetermining Permissible Lengths 30mm General Fitting NotesMin metres Flue Trim Spigot ScrewPlume Outlet Elbow Installation Initial PreparationFlushing Preparing The BoilerFitting The Boiler Condensate Drain see sectionPressure Relief Valve Discharge Pipe Wall Plate Remove the sealing caps from the boiler connectionsFitting The Flue Wall Thickness Flue Elbow AdaptorWasteY Flue Inner Flue Support Bracket Flue Elbow Vertical FlueMaking The Electrical Connections Preliminary Electrical ChecksCommissioning the Boiler Commissioning the BoilerChecking the Burner Pressure Pressure Test Point Sealing ScrewCompletion CompletionCase Front Panel Facia Panel Servicing the Boiler 13 .1 Annual ServicingAnnual Servicing Changing Components Pressure Switch FigFan Figs Heat Exchanger Fig 14.0 Changing ComponentsBurner Fig Injectors Fig Electrodes FigInsulation Fig Reassemble in reverse orderCentral Heating Temperature Sensor Fig Safety Thermostat FigDHW Temperature Sensor Fig Gas Valve FigPump Complete Fig Pump Head Only FigAutomatic Air Vent Fig Expansion Vessel Fig Pressure Gauge FigsCondensate Trap Fig Selector Switch Fig 14.19 P.C.B. FigPlate Heat Exchanger Fig Diverter Valve Assembly Flow Regulator FigsSecondary Heat Exchanger Fig Flue Overheat Thermostat FigIllustrated Wiring Diagram Control PCBFault Finding Microswitch terminals Diverter valve spindle Assembly faultyDomestic Hot Water Follow operational sequence Turn selector to neon illuminatedCheck wiring PCB A4 connector Replace selector Terminals 4 Replace pump PCB A4 connector terminals 3 Replace PCBPCB A2 connector, is Across terminals 5 Replace microswitchPCB A1 connector has 230V AC Turn selector switchTo ‘Reset’ position Gas at burnerON/OFF/RESET selector when turned to ‘Reset’ position Short Parts List Short Parts List131 154GAS Boiler Commissioning Checklist Service Interval Record Potterton
Related manuals
Manual 12 pages 48.65 Kb

30 HE specifications

The Baxi Potterton 30 HE is a popular choice among homeowners seeking an efficient and reliable boiler solution. Recognized for its compact design and advanced technologies, this boiler is ideal for various residential heating needs.

One of the standout features of the Baxi Potterton 30 HE is its high efficiency rating, which ensures lower energy consumption and reduced utility bills. With an impressive efficiency of up to 90%, this boiler operates at a much higher capacity compared to older models, making it both environmentally friendly and cost-effective. The 30 HE is particularly well-suited for medium to larger homes with a higher demand for hot water.

The Baxi Potterton 30 HE incorporates a range of innovative technologies aimed at enhancing performance and reliability. The automatic modulation function adjusts the boiler's output according to demand, ensuring that it only works as hard as necessary. This not only prolongs the lifespan of the unit but also maximizes comfort levels in the home.

Another feature of the 30 HE is its low noise operation. This boiler has been specifically designed to minimize sound, allowing it to operate quietly in the background without disturbing daily activities. This makes it an ideal choice for homes where noise can be a concern, particularly in open-plan living spaces.

The compact dimensions of the Baxi Potterton 30 HE make it easy to install in various locations, whether it be in a kitchen, utility room, or even a loft space. Its lightweight construction further simplifies the installation process, saving both time and labor costs.

In terms of user-friendliness, the boiler is equipped with an intuitive control panel that allows homeowners to easily adjust settings and monitor performance. This user-centric design ensures that even those who may not be technically inclined can manage their heating requirements with ease.

Safety features are also a priority in the design of the Baxi Potterton 30 HE. It includes built-in safety mechanisms such as frost protection and a burner pressure monitoring system, which work to prevent overheating and ensure optimal operation.

Overall, the Baxi Potterton 30 HE is an efficient, reliable, and user-friendly boiler that meets the heating demands of modern homes. Its blend of advanced technologies, compact size, and focus on safety make it a standout choice for homeowners seeking a high-performance heating solution.
Top Page Image Contents