State Industries SBN85390NE/A warranty Lighting and Operation Instructions, Operating Instructions

Page 24

LIGHTING AND OPERATION INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A. This appliance does not have a pilot. It is equipped •

If you cannot reach your gas supplier, call the fire

with an ignition device which automatically lights the

department.

burner. Do not try to light the burner by hand.

 

B.BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

“WHAT TO DO IF YOU SMELL GAS”

Do not try to light any appliance.

Do not touch any electric switch; do not use any telephone in your building.

Immediately call your gas supplier from a neighbor’s telephone. Follow the gas supplier’s instructions.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted repair may result in fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

OPERATING INSTRUCTIONS

1.

STOP! Read the safety information above on this

9.

Set thermostat to desired setting.

 

label.

 

 

10.

If the appliance will not operate, follow the

 

 

 

 

2.

Set thermostat to lowest setting.

 

 

instructions “To Turn Off Gas To Appliance” and call

3.

Turn off all electric power to the appliance.

 

 

your service technician or gas supplier.

 

 

 

4.

This appliance is equipped with an ignition device

 

 

 

which automatically lights the burner. Do not try to

 

 

 

light the burner by hand.

 

 

 

 

5.

Push in gas control knob slightly and turn clockwise

 

 

 

to “OFF”.

 

 

 

 

6.

Wait five (5) minutes to clear out any gas.

If you

 

 

 

then smell gas,

STOP! Follow “B” in the

 

 

 

safety information

above on this label. If you

 

 

 

don’t smell gas, go on to the next step.

 

 

 

7.

Turn gas control knob counterclockwise

to “ON”.

 

 

8.

Turn on all electric power to the appliance.

 

 

 

FOR YOUR SAFETY READ BEFORE OPERATING

1.Set the thermostat to lowest setting.

2.Turn off all electric power to appliance if service is to be performed.

3.Push in gas control knob slightly and turn clockwise to “OFF”. Do not force.

24

Image 24
Contents Models SBN71120NE Thru SBN85390NE/A Series ROUGH-IN-DIMENSIONS Front View TOP View Back View ROUGH-IN-DIMENSIONSGasand Electrical Characteristics Table of Contents ForewordGeneral Safety Information Features High Altitude InstallationsSELF-CLEANING Hydro Cannon High Limit SwitchExhaust Inducer Blower Assy Circulating PumpDishwashing Machine Requirement UncratingLeveling ClearancesModel Right Back Ceiling SideHard Water AIR RequirementsVenting UnconfinedspaceTechnical Data Venting Type B GAS VentTechnical Data Venting Multiple Heater Manifold Water Line ConnectionsWater Potable Heating and Space Relief ValveInstallation DIAGRAMS-TOP INLET/OUTLET Usage Tube Inlet InstallationGeneral Code RestrictionsVertical Storage Tank and Forced Circulation Horizontal Storage Tank and Forced CirculationPage Installation DIAGRAMS-SIDE INLET/OUTLET Usage Circulating Return Line ConnectionHeater with Mixing Valve and Recirculated Sanitizing Loop TWO PRE-HEATERS with Booster Heater Horizontal Storage Tank Model Dimension a Manifold KitsTWO Unit Manifold KIT Three Unit Manifold KIT Four Unit Manifold KITHeater Wiring Single Unit Wiring Diagram SBN-120 Through 400AGAS Pipingand Dirt LEG Installation GAS PipingGAS Pressure Regulator PurgingOperation Manifold GAS Pressure in Inches Water Column ALL ModelsFilling Sequence of Operation For Your Safety Read Before Operating Lighting and Operation InstructionsOperating Instructions Preventive Maintenance Water Temperature ControlCheck the Ignitor Assembly Ignitor AssemblyMain Burner GAS ValvesChecking the Input Remote Storage Tank Temperature Control Venting SystemHOT Water Odor Anode ROD InspectionTank Cleanout Procedure Deliming Using FLO-JUG MethodDeliming Solvents Service System DiagnosticsIgnition Module System Electrical ServicingReplacement PARTS, Service Handbooks and Training Aids Sequence of Operation Flow ChartYES Operational Checklist Complaint Cause User ServicemanLindahl Parkway Ashland City, TN Phone 800-821-2017 Fax