Husqvarna E20 manual Important Safety Instructions

Page 2

This houshold sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed, including the following:

Read all instructions before using this household sewing machine.

DANGER - To reduce the risk of electric shock:

A sewing machine should never be left unattended when plugged in. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning.

Always unplug before relamping. Replace bulb with same type rated 10 Watt (110-120V), 15 Watt (220-240V).

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons:

Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children and infirm persons.

Use this sewing machine only for its intended use as described in this manual. Use only attachments recommended by the manufacturer as contained in this manual.

Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.

Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot controller free from the accumulation of lint, dust, and loose cloth.

Keep fingers away from all moving parts. Special care is required around the sewing machine needle.

Always use the proper needle plate. The wrong plate can cause the needle to break.

Do not use bent needles.

Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

Switch the sewing machine off (“0”) when making any adjustment in the needle area, such as threading needle, changing needle, threading bobbin, or changing presser foot, etc.

Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual.

Never drop or insert any object into any opening.

Do not use outdoors.

Do not operate where aerosol (spray) products are being used or where oxygen is being administrated.

To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.

Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

SAVE THESE INSTRUCTIONS

Image 2
Contents E20 Important Safety Instructions Contents Principal Parts Page Accessories Slide on the SNAP-IN Accessory BOX Connecting the Machine to Power Source For the USA and CanadaChanging the Bulb Replace bulb with same type rated WattsAdjusting the Presser Foot Pressure TWO-STEP Presser Foot LeverAttaching the presser foot Presser Foot ShankAttaching the presser foot shank Removing the presser footWinding the Bobbin Inserting the Bobbin Changing the Needle System 130/705H Threading the Upper Thread Bringing UP the Bobbin Thread Thread Tension Upper thread tensionRaise or Lower the Feed DOG Removing the Fabric Reverse SewingChanging Sewing Directions Cutting the ThreadHOW to Choose Your Pattern Matching Needle / Fabric / Thread Needle, fabric, thread selection guideFunction of stitch length dial while zigzaging ZIG ZAG SewingFunction of stitch width dial Satin stitchStraight Stitching and Needle Position Double overlock stitch Overlock StitchesSeams, overcasting, visible hems Standard overlockBlind HEM Making a Buttonhole on Stretch Fabrics E ONE Step ButtonholesMaking a Buttonhole Left and Right Side Balance for Buttonhole Zippers and Piping Joining fabric Step ZIG-ZAGSewing elastic Triple zig-zag 2/4 Stretch Stitch SelectionTriple straight stitch 1/3 Free Motion Darning Darning Quilting Cleaning and lubricating the hook MaintenanceCleaning the feed dog Remove the stitch plateTroubleshooting Guide Problem Cause CorrectionVSM Group AB SE-561 84 Huskvarna Sweden