Dansons Group IGB, FGB manual Tools Required, Power Tools, Hand Tools, Supplies

Page 16

TOOLS REQUIRED

Before starting your Glow Boy Multi-Fuel install, we recommended you have the following list of tools ready. This is not an exhaustive list, but should go along way in making your installation easier.

Power Tools

Shop Vacuum WITH Filter

Jigsaw or Reciprocating saw

Electric drill

Extension cord

4” or 5” diameter coring bit and drill (if going through concrete)

Hand Tools

Tape Measure

Caulking Gun

Circle Maker

Allen (Key) wrench set

Stud Finder

Set of sockets or nut driver 1/4”, 5/16” and 7/16”

Assortment of Phillip, Robertson and slot screwdrivers

Assortment of sheet and wood drill bits Flashlight

Wire stripper and wire cutter

Hammer

Bubble Level

Utility knife

Adjustable pliers (6 to 8 inches)

Small hand broom and dustpan

Furniture and Floor Protection

Supplies

Caulking tube of RTV Hi-Heat Silicone

Caulking tube of Clear Silicone

Hi–Heat Aluminum Foil Tape

2” long Wood screws (10+) Assortment of sheet and wood screws “Stove Bright” Hi-Heat Stove Paint

Glow Boy Pellet & Biomass	www.glowboystoves.com	16
		16

Image 16

Contents Toll Free Technical Support Glowboy 456 Dear Glow Boy Multi-Fuel / Pellet Stove Owner Friendly ReminderTable of Contents Grounded surge-protection unit is recommended Safety PrecautionsDo not unplug the stove if you suspect a malfunction Safety Testing HOW Your Appliance Works Fuel ConsiderationsAutomatic Safety Features Specifications Heating SpecificationsDimensions Electrical SpecificationsPlanning & Installation Check List Placement is decided onNecessary for your stove EssentialPLANNING-EXHAUST Systems Vent Safety PrecautionsPellet Vent Type Determine Venting Size and Distance PLANNING- Exhaust Systems …Step Pellet Vent Termination Figures 7 Vent Termination ClearancesOutside air is Required on ALL Mobile Home Installations PLANNING- Outside AIRThrough The Wall Kits Include Foot Package PART#Stove Placement Clearances Straight InstallationPLANNING- Protection & Clearances Floor Protection RequirementsAlcove Installation Clearances Corner InstallationPLANNING- Protection & Clearances . . . CON’T Power Tools Tools RequiredHand Tools SuppliesINSTALLATION-FREESTANDING Through the WallMobile Home Installation Ceiling and Roof Must be MaintainedFreestanding Installation . . . CON’T Hearth Stove Existing RelineFreestanding Installation . . . C on ’ T Fireplace Insert InstallationFull Chimney Reline Direct Connection BUILT-IN Installation BUILT-IN Insert Installation . . . CON’T Minimum Framing DimensionsTop Clearance Back ClearanceSetting the AIR Inlet Damper Operating InstructionsOpening and Closing the Main Door Seating the Burn GrateBasic Overview Fill the Hopper with FuelOperating in Manual Mode To Start Choose Mode of OperationManual Operation Thermostat On/Off Thermostat Low/High Operating in Thermostat High / LOW Cycle Flashing 3 To Start … con’t After Pushing the Start touch padTrim Pots Fine Tune Adjustments- Factory Settings Auger CycleOperating INSTRUCTION- Lighting Your Appliance OPERATION- Performance Enhancements Giving Your Appliance a TUNE-UPFuel SPECIFICATIONS-WOOD Pellets Fuel Rate Setting…Ash Content LengthFuel SPECIFICATIONS-SHELLED Corn Corn QualityMAINTENANCE-ROUTINE Cleaning Window CleaningDoor & Trim Cleaning Every 2 -3 Days / WeeklyTON, Seasonal or BI-SEASONAL MAINTENANCE- Periodic CleaningExhaust Venting Check and Clean the Hopper Yearly Maintenance Trouble ShootingService Contracts Dansons Customer Service atCont… Fuel feeds into the burnGrate but will not start Burn grate fills with fuelFire burns with a yellow Flame. Fuel builds upBurn grate. Window Gets real dirty quicklyOptional Accessories Limited Warranty Parts, Service and ReturnsExtended Warranty Additional Dansons Products