Dansons Group IGB Operating Instructions, Setting the AIR Inlet Damper, Seating the Burn Grate

Page 24

OPERATING INSTRUCTIONS

COMPLETE THE CHECK LIST (Page 9) PRIOR TO LIGHTING YOUR FIRST FIRE FOLLOW THE ARROWS TO START YOUR APPLIANCE FOR THE FIRST TIME

IT IS CRITICAL FOR THE CORRECT OPERATION OF YOUR STOVE THAT THE FOLLOWING STEPS BE PERFORMED! A pellet stove, like most things is life is NOT a plug and play appliance.

SETTING THE AIR INLET DAMPER

Because the appliance is made in one location and elevation, then shipped, moved and installed to a different location, at a different elevation, vented differently and then using different fuels. It is

not possible for the manufacture to factory set your stove to work properly without some adjustments.

The damper helps to control the amount of airflow supplied for combustion.

Damper pushed in all the way airflow is minimum.

Damper pulled out all the way airflow is increased.

To get the appliance started, push the air damper in all the

Way, then pull outward approximately 1/2”.

This may not be the final setting.

We will cover FINE TUNNING YOUR STOVE later in this manual.

OPENING AND CLOSING THE MAIN DOOR:

Open the stove door by rotating the handle COUNTER CLOCKWISE, toward the TOP of the stove, until the handle is about the 3 o’clock position. Swing door open to the

left.

Close the stove door by keeping the handle at the

3 o’clock position. Push the door firmly against the stove. Rotate the handle downward to the 6 0’clock position to lock.

SEATING THE BURN GRATE:

Diagram A

The SUPER GRATE multi-Fuel Burn Grate comes in one piece: (B) and sits in the Burn Pot (A)

Diagram B

B

G

C

A

Ensure the Multi-Fuel Burn Grate (A) is properly seated in the burn pot and holes are free from obstructions .

The burn grate front lip must sit firmly on the top of the burn pot.

Diagram B and C

You may need adjust the spacer tab (C) if the burn grate fits loosely in the burn pot or if the Igniter hole needs to be closer to the igniter.

To do so grasp the burn grate adjustment tab (C) with a pair of pliers and bend it slightly inward or outward, until the burn grate top rest tightly onto the burn pot and grate fits firmly, with slight play, in the burn pot.

C

Diagram B

Diagram A

Diagram C

Glow Boy Pellet & Biomass

www.glowboystoves.com

24

 

 

24

 

 

 

Image 24
Contents Toll Free Technical Support Glowboy 456 Dear Glow Boy Multi-Fuel / Pellet Stove Owner Friendly ReminderTable of Contents Safety Precautions Grounded surge-protection unit is recommendedDo not unplug the stove if you suspect a malfunction Safety Testing HOW Your Appliance Works Fuel ConsiderationsAutomatic Safety Features Specifications Heating SpecificationsDimensions Electrical SpecificationsPlanning & Installation Check List Placement is decided onNecessary for your stove EssentialVent Safety Precautions PLANNING-EXHAUST SystemsPellet Vent Type PLANNING- Exhaust Systems … Determine Venting Size and DistanceStep Pellet Vent Termination Figures 7 Vent Termination ClearancesOutside air is Required on ALL Mobile Home Installations PLANNING- Outside AIRThrough The Wall Kits Include Foot Package PART#Stove Placement Clearances Straight InstallationPLANNING- Protection & Clearances Floor Protection RequirementsClearances Corner Installation Alcove InstallationPLANNING- Protection & Clearances . . . CON’T Power Tools Tools RequiredHand Tools SuppliesINSTALLATION-FREESTANDING Through the WallMobile Home Installation Ceiling and Roof Must be MaintainedFreestanding Installation . . . CON’T Hearth Stove Existing RelineFreestanding Installation . . . C on ’ T Fireplace Insert InstallationFull Chimney Reline Direct Connection BUILT-IN Installation BUILT-IN Insert Installation . . . CON’T Minimum Framing DimensionsTop Clearance Back ClearanceSetting the AIR Inlet Damper Operating InstructionsOpening and Closing the Main Door Seating the Burn GrateBasic Overview Fill the Hopper with FuelChoose Mode of Operation Operating in Manual Mode To StartManual Operation Thermostat On/Off Thermostat Low/High Operating in Thermostat High / LOW Cycle Flashing 3 To Start … con’t After Pushing the Start touch padTrim Pots Fine Tune Adjustments- Factory Settings Auger CycleOperating INSTRUCTION- Lighting Your Appliance OPERATION- Performance Enhancements Giving Your Appliance a TUNE-UPFuel SPECIFICATIONS-WOOD Pellets Fuel Rate Setting…Ash Content LengthFuel SPECIFICATIONS-SHELLED Corn Corn QualityMAINTENANCE-ROUTINE Cleaning Window CleaningDoor & Trim Cleaning Every 2 -3 Days / WeeklyMAINTENANCE- Periodic Cleaning TON, Seasonal or BI-SEASONALExhaust Venting Check and Clean the Hopper Yearly Maintenance Trouble ShootingService Contracts Dansons Customer Service atCont… Fuel feeds into the burnGrate but will not start Burn grate fills with fuelFire burns with a yellow Flame. Fuel builds upBurn grate. Window Gets real dirty quicklyOptional Accessories Limited Warranty Parts, Service and ReturnsExtended Warranty Additional Dansons Products