Bosch Appliances 3931A Removing the Dust BAG, Removing the Filter Cartridges, Replacing the Motor

Page 7

BM 1609929K45 08-06 8/14/06 11:42 AM Page 7

FIG. 4

FILTER

 

CARTRIDGE

 

CONTROL UNIT TOP

 

SECTION

FILTER

CONTROL UNIT

COMPARTMENT

BOTTOM SECTION

LOCK

 

 

MOTOR PROTECTION

 

FILTER

2.Grasp a new dust bag at the flange. Push it over the bottom of the connection piece first and then over the catch on the top of the connection piece. Make sure that the full length of the dust bag faces against the inner wall of the canister (Fig. 2).

3.Re-attach the control unit.

4.Lock the canister latches.

REMOVING THE DUST BAG

1.Unlock the canister latches and remove the control unit.

2.Pull the dust bag away from and off of the connection piece.

3.Close the opening in the dust bag by folding down the lid

4.Remove bag and dispose of properly.

REMOVING THE FILTER CARTRIDGES

1.First, clean the filters by setting the mode selector switch to the PULSE-CLEAN™ mode, which takes only 10 seconds.

2.To open the filter access compartment, use a coin to rotate the filter compartment lock by 1/4 turn in the direction of the arrow and push the lock in.

3.Lift up the top section of the control unit.

4.Grasp the filter cartridge by the fins, pull up and remove.

Replace a damaged filter cartridge immediately.

THOROUGH CLEANING OF THE

FILTER CARTRIDGES

If necessary, the filter cartridges can also be cleaned with a soft brush and can also be washed with water.

REPLACING THE FILTER CARTRIDGES

1.Insert new or cleaned filter cartridge and ensure firm seating.

2.Lower the top section down again.

3.With slight pressure from the top of the control unit, the filter compartment lock will snap back again.

CLEANING THE MOTOR

PROTECTION FILTERS

The motor protection filters are mostly maintenance-free. If the motor filters are dirty, it may indicate that the filter cartridges are damaged and need to be replaced. If the motor filters need cleaning, take out the motor protection filters from time to time and wash them. Allow them to dry thoroughly before reinserting.

REMOVING THE MOTOR

PROTECTION FILTERS

1.To open the filter access compartment, use a coin to rotate the lock by 1/4 turn in the direction of the arrow and push the lock in.

2.Lift up the top section.

3.Grasp the filter, pull up and remove.

REPLACING THE MOTOR

PROTECTION FILTERS (See Figure 4.)

1.Insert clean motor protection filters and ensure firm seating.

2.Lower the top section.

3.With slight pressure from the top of the control unit, the filter compartment lock will snap back again.

WAND STORAGE

The wands from the optional VAC011 wand kit can be stored in the recesses at the bottom of the rear of the container. See Figure 1.

-7-

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Read Before Using Work Area General Safety RulesElectrical Safety Personal Safety and Vacuum UseService Vacuum Cleaner Safety RulesVacuum Care Standard Equipment Functional Description and SpecificationsAll-Purpose Vacuum Cleaner SpecificationsBIA M Assembling the Main Handle Assembly & PreparationInstalling the Dust BAG Attaching the Rear WheelsRemoving the Filter Cartridges Thorough Cleaning Filter CartridgesCleaning the Motor Protection Filters Removing the Dust BAGOperating Instructions Normal Vacuuming ModePower Tool Activation Mode Power BrokerPULSE-CLEAN Mode PULSE-CLEAN Filter CleaningPULSE-CLEAN Mode Combined with Power Tool Activation Emptying the Canister Canister MaintenanceWET Vacuuming Your 3931A can also be used for wet vacuumingCertain cleaning agents ! Caution and solvents damage MaintenanceAccessories CleaningBosch Vacuum Hoses & Adapters Other Accessories Sécurité personnelle et utilisation de ’aspirateur Consignes générales de sécuritéAire de travail Sécurité électriqueEntretien de l’aspirateur Consignes de sécurité pour les aspirateursEntretien Équipement standard Aspirateur tous-usagesCaractéristiques 100 po 13,3 gal L11,35 gal L Gal LMontage DE LA Poignée Principale Installation DU SAC a PoussièreAssemblage & Préparation Montage DES Roues ArrièresNettoyage DES Filtres DE Protection DU Moteur Remplacement DES Cartouches FiltrantesRemplacement DES Filtres DE Protection DU Moteur Pour Enlever LE SAC À PoussièreNe convient pas pour Mode D’ASPIRATION NormaleMode Dalimentation Power Broker Instructions utilisationArrêt de l’aspirateur PULSE-CLEANMode DE Nettoyage PAR Impulsions PULSE-CLEAN Mise en marche de laspirateurVidange DU Réservoir Aspiration DE LiquidesVidez le réservoir avant d’aspirer des liquides Entretien DES Capteurs DE Niveau D’EAU’entretien préventif AccessoiresIndicateur D’ENTRETIEN Adaptateurs ET Tuyaux D’ASPIRATION Bosch Non illustré VAC015 Autres AccessoiresVAC011 Non illustré VAC014Seguridad personal y uso de la aspiradora Normas generales de seguridadÁrea de trabajo Seguridad eléctricaLávese las manos después de manejarlo Normas de seguridad para aspiradorasCuidado de la aspiradora Servicio de ajustes y reparacionesEspecificaciones Descripción funcional y especificacionesAspiradora de uso general Equipo estándarÁrea de la superficie del cartucho de filtro Gal 45 lPulgadas MilibaresInstalación DE LA Bolsa Para Polvo Montaje y preparaciónVoltee el recipiente sobre uno de sus lados Montaje DEL ASA PrincipalRemoción DE LOS Filtros DE Protección DEL Motor Remoción DE LA Bolsa Para PolvoReemplazo DE LOS Cartuchos DE Filtro Limpieza DE LOS Filtros DE Protección DEL MotorAjuste el dial a la diferencia Dispositivo DE Asignación DE Potencia Power BrokerInstrucciones de funcionamiento Modo DE Recogida NormalEncendido DE LA Aspiradora Limpieza DEL Filtro PULSE-CLEANModo PULSE-CLEAN Notas sobre PULSE-CLEANMantenimiento DEL Recipiente Recogida DE Materiales MojadosMantenimiento DE LOS Sensores DEL Nivel DE Agua Vaciado DEL RecipienteLimpieza MantenimientoAccesorios ServicioMangueras Y Adaptadores DE Aspiración Bosch No mostrado VAC014 Otros AccesoriosNo mostrado VAC015 BM 1609929K45 08-06 8/14/06 1142 AM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools
Top Page Image Contents