GTO UL325 SERIES installation manual Installing the Post Bracket Assembly and Gate Bracket

Page 19

Installing the Post Bracket Assembly and Gate Bracket

Step 7

Mark reference points for bolt holes on the fence post through middle of bracket slots. Marking reference points in this manner allows room for adjustment when mounting the post bracket assembly and gate bracket. After marking your reference points, remove the opener and brackets from the fence and gate.

Step 8

Drill 3/8" holes into fence post as marked.

Step 9

Fasten post bracket assembly to the fence post using

(4)3/8" x 8" bolts, washers, lock washers, and nuts (provided). Remove excess bolt length extending beyond the tightened nuts with a hacksaw or bolt cutters.

NOTE: In cases where the fence post has a diameter larger than 6", threaded rods or carriage bolts longer than 8"

(not supplied) must be used.

Step 10

Mark reference points for bolt holes on the gate cross member

through middle of gate bracket slots. Drill 3/8" holes into the gate cross member as marked.

Mark fence post through middle of bracket slots and drill 3/8" holes

Post Bracket

Assembly

SIDE VIEW

Remove excess bolt length  with hacksaw or bolt cutters

EXAMPLES TOP VIEW

Round Metal Post

Square Metal Post

Square Wood Post

Round Wood Post

Mount gate bracket using (2)

3/8" x 3" bolts, washers, lock washers, and nuts (provided). Cut off excess bolt length extending beyond the tightened nuts.

Gate In Open Position

Mark cross member through middle of gate bracket slots and drill 3/8" holes

Gate Bracket Mounting Examples

FRONT VIEW

SIDE VIEW

Round Tube & Chain Link Gate

FRONT VIEW

SIDE VIEW

Mounting Plate  Created for  Decorative Gate (required but not supplied)

Square Tube Gate

Remove excess bolt length  with hacksaw or bolt cutters

15

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 350 Installation Manual forPlace of Purchase When You Know Multiply By To Find SymbolTable of Contents Please Read this First Switch is OFF and the gate is not moving Disconnecting the OpenerEntrapment Zones for a Pull-To-Open Application For The ConsumerPull-To-Open Application II. During InstallationAny control device Within gray area III. After Installation Secondary Means of Protection Against Entrapment Entrapment Alarm UL 325 30A.1.1AInstall Warning Signs Required Safety Precautions for GatesEntrapment Protection 350 Hardware Bag Contents Tools Needed Mighty Mule 350 E-Z Gate Opener Technical SpecificationsStep Installation OverviewPreparation of the Gate Pull-to-Open Gates Gate Opens into the PropertyRecommended Reinforcement Examples Installation of Mounting HardwarePost Bracket Assembly Closed Position Gate Bracket Mounting Examples Installing the Post Bracket Assembly and Gate BracketMounting the Opener Installation of the Closed Position StopCheck List Preparing to Activate the SystemSolar Panel and Gate Acticity Chart Powering the SystemConnecting the Battery MIghty Mule Wire Routing Important Deailed Wire Routing DiagramsImportant Information about LOW Voltage Wire Connecting the TransformerMake sure the exposed wires do not touch each other DIP Switch #1 Push/Pull-to-Open Connecting Solar PanelsDIP Switches Main DIP Switch Settings ModesYour Mighty Mule 350 has two Limit Settings Setting the Closed Position LimitClosed Limit setting Setting Auto-Close Time Obstruction Sensitivity Potentiometer SettingRemove the Transmitter Cover Set the transmitter DIP SwitchesTeach the New Code to Control Board Memory Run the cable through PVC conduit to protect it from damage Installing the ReceiverContact Sensors safety edges Connecting Additional Safety DevicesIf not installing a contact sensor skip to next section Exit Loop If not installing a non-contact sensor skip to next sectionIf not installing a shadow loop skip to next section Non-Contact Sensors photo beamsIf not connecting accessories skip to next section Connecting AccessoriesAutomatic Gate Lock FM143 Mighty Mule Free Entry/Exit Loop Wiring Driveway Loops to the Mighty MuleMighty Mule Gate Opening Sensor FM138 When everything has been connected to the openerSwinging gates shall not open into public access areas Push to Open InstallationMODE2 LOCK/BEACON Setting the Open Position LimitTesting Your Open Limit Setting Beeps with 2 seconds off Beep when attempt to run the unit No battery is connectedPower-Cycle Beep with 2 seconds offCharging LED Red Power LED GreenGate Closes Then Opens Again on its Own Gate Opens Then Closes Again on its OwnGTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USA Repair ServiceGate Mail techsupport@gtoinc.comMASONRY, BRICK, or Rock etc. Columns Column Installation InformationAccessories Low Voltage Wire RB509

UL325 SERIES specifications

The GTO UL325 Series is a highly regarded line of gate operators, designed to meet the needs of both residential and commercial applications. With its commitment to safety, durability, and efficiency, the UL325 Series has set a standard in the industry for gate automation solutions.

One of the main features of the GTO UL325 Series is its robust safety mechanisms. The operators are designed to comply with the rigorous UL 325 safety standards, which is essential for ensuring user safety and preventing accidents during gate operation. This includes advanced features such as obstacle detection, which allows the system to sense when an object is in the path of the gate and stop or reverse the motion to prevent harm or damage.

The UL325 Series comes with a reliable and efficient motor that provides powerful performance while operating gates of various sizes and weights. This versatility allows it to be used for a range of gate types, including swing gates and sliding gates. The motors are also designed for quiet operation, minimizing noise disturbances in residential areas.

Additionally, the GTO UL325 Series incorporates smart technology features that enhance user experience. The built-in remote control system allows users to open and close their gates with the simple push of a button from a distance. Some models also support compatibility with smartphone apps, providing users with a modern and convenient way to control their gates from anywhere.

Durability is another characteristic of the GTO UL325 Series. Constructed with high-quality materials, these gate operators are built to withstand harsh weather conditions, making them suitable for various climates. This longevity ensures that users receive a reliable product that will serve their needs for years to come.

Another noteworthy aspect of the GTO UL325 Series is the ease of installation and maintenance. The operators are designed for straightforward installation, allowing both professionals and DIY enthusiasts to set them up with minimal hassle. Additionally, regular maintenance is simplified, with clear guidelines provided to ensure longevity and reliability.

In conclusion, the GTO UL325 Series is an exemplary choice for those seeking a reliable, safe, and technologically advanced gate operator. With its emphasis on safety, versatility, and user-friendly features, it stands out in the marketplace, making it an ideal solution for both residential and commercial gate automation needs. Investing in a GTO UL325 operator means investing in peace of mind, knowing that one has a dependable and efficient gating solution.
Top Page Image Contents