GTO UL325 SERIES Beep with 2 seconds off, Beeps with 2 seconds off, Learn Remote, Power-Cycle

Page 40

Maintenance & Troubleshooting Guide

If your gate opener does not function properly after it is installed, use this guide before calling the GTO Service Department.

•On all gates weighing 250 lb. or more, routinely grease the ball bearing hinges at least 4 times a year; more frequently if the gates are in a coastal area.

•Clean the push-pull tube with a soft, dry cloth and apply silicone spray to it at least once a month.

•While oxidation is a normal part of weathering of equipment that is exposed to the elements, we recommend you apply silicone spray the front and rear mounts to minimize this effect.

Audible/Buzzer/Alarm Feedback:

1.1 beep with 2 seconds off:

Limit switch error: Limit switch’s normally open and normally close inputs both open or both shorted. The alarm will automatically shut off in 4 seconds after the problem is corrected.

2.5 beeps with 2 seconds off:

Low battery condition detected: Low battery can occur if the following condition is detected: While in idle state and the battery voltage is below ~11.5 Volts.

While running and the battery voltage is below ~10.0 Volts.

The alarm will automatically shut off when the idle voltage is more than 12 Volt. The unit may continue to operate even when low battery is detected.

The STATUS LED will also blink when the buzzer is beeping. See page 36 #3 and #4.

3.1 beep when attempt to run the unit: No battery is connected.

Blown fuse

Dead cell or extremely low battery condition.

4.Alarm continuously beeps (remote does not operate unit AND not at either limits): Two consecutive obstructions have been detected without reaching the limit. Alarm will

automatically shut off after 5 minutes. ‘Power-cycle’ the unit will also shut off the alarm.

5.Learn Remote:

When a new code is learned from the remote the alarm will sound. Release the ‘LEARN REMOTE’ button will turn the alarm off. See "Setting Your Personal Transmitter Code" section on page 26.

6.Power-Cycle:

The alarm will beep for 1 second upon power up.

B)Visual/LEDs Feedback:

1.RF LED (LED2):

Blinking when there is 318 MHz signal is received. This LED is typically off when the receiver is connected and no 318 MHz signal is presented.

36

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Installation Manual for 350When You Know Multiply By To Find Symbol Place of PurchaseTable of Contents Please Read this First Disconnecting the Opener Switch is OFF and the gate is not movingFor The Consumer Entrapment Zones for a Pull-To-Open ApplicationPull-To-Open Application II. During InstallationAny control device Within gray area III. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentInstall Warning Signs Required Safety Precautions for GatesEntrapment Protection 350 Hardware Bag Contents Tools Needed Technical Specifications Mighty Mule 350 E-Z Gate OpenerInstallation Overview Preparation of the GatePull-to-Open Gates Gate Opens into the Property StepInstallation of Mounting Hardware Recommended Reinforcement ExamplesPost Bracket Assembly Closed Position Installing the Post Bracket Assembly and Gate Bracket Gate Bracket Mounting ExamplesInstallation of the Closed Position Stop Mounting the OpenerPreparing to Activate the System Check ListPowering the System Solar Panel and Gate Acticity ChartConnecting the Battery Important Deailed Wire Routing Diagrams MIghty Mule Wire RoutingConnecting the Transformer Important Information about LOW Voltage WireMake sure the exposed wires do not touch each other Connecting Solar Panels DIP SwitchesMain DIP Switch Settings Modes DIP Switch #1 Push/Pull-to-OpenYour Mighty Mule 350 has two Limit Settings Setting the Closed Position LimitClosed Limit setting Obstruction Sensitivity Potentiometer Setting Setting Auto-Close TimeRemove the Transmitter Cover Set the transmitter DIP SwitchesTeach the New Code to Control Board Memory Installing the Receiver Run the cable through PVC conduit to protect it from damageContact Sensors safety edges Connecting Additional Safety DevicesIf not installing a contact sensor skip to next section If not installing a non-contact sensor skip to next section If not installing a shadow loop skip to next sectionNon-Contact Sensors photo beams Exit LoopIf not connecting accessories skip to next section Connecting AccessoriesAutomatic Gate Lock FM143 Wiring Driveway Loops to the Mighty Mule Mighty Mule Free Entry/Exit LoopWhen everything has been connected to the opener Mighty Mule Gate Opening Sensor FM138Push to Open Installation Swinging gates shall not open into public access areasSetting the Open Position Limit MODE2 LOCK/BEACONTesting Your Open Limit Setting Beep when attempt to run the unit No battery is connected Power-CycleBeep with 2 seconds off Beeps with 2 seconds offPower LED Green Gate Closes Then Opens Again on its OwnGate Opens Then Closes Again on its Own Charging LED RedRepair Service GateMail techsupport@gtoinc.com GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USAColumn Installation Information MASONRY, BRICK, or Rock etc. ColumnsAccessories Low Voltage Wire RB509

UL325 SERIES specifications

The GTO UL325 Series is a highly regarded line of gate operators, designed to meet the needs of both residential and commercial applications. With its commitment to safety, durability, and efficiency, the UL325 Series has set a standard in the industry for gate automation solutions.

One of the main features of the GTO UL325 Series is its robust safety mechanisms. The operators are designed to comply with the rigorous UL 325 safety standards, which is essential for ensuring user safety and preventing accidents during gate operation. This includes advanced features such as obstacle detection, which allows the system to sense when an object is in the path of the gate and stop or reverse the motion to prevent harm or damage.

The UL325 Series comes with a reliable and efficient motor that provides powerful performance while operating gates of various sizes and weights. This versatility allows it to be used for a range of gate types, including swing gates and sliding gates. The motors are also designed for quiet operation, minimizing noise disturbances in residential areas.

Additionally, the GTO UL325 Series incorporates smart technology features that enhance user experience. The built-in remote control system allows users to open and close their gates with the simple push of a button from a distance. Some models also support compatibility with smartphone apps, providing users with a modern and convenient way to control their gates from anywhere.

Durability is another characteristic of the GTO UL325 Series. Constructed with high-quality materials, these gate operators are built to withstand harsh weather conditions, making them suitable for various climates. This longevity ensures that users receive a reliable product that will serve their needs for years to come.

Another noteworthy aspect of the GTO UL325 Series is the ease of installation and maintenance. The operators are designed for straightforward installation, allowing both professionals and DIY enthusiasts to set them up with minimal hassle. Additionally, regular maintenance is simplified, with clear guidelines provided to ensure longevity and reliability.

In conclusion, the GTO UL325 Series is an exemplary choice for those seeking a reliable, safe, and technologically advanced gate operator. With its emphasis on safety, versatility, and user-friendly features, it stands out in the marketplace, making it an ideal solution for both residential and commercial gate automation needs. Investing in a GTO UL325 operator means investing in peace of mind, knowing that one has a dependable and efficient gating solution.
Top Page Image Contents