GTO UL325 SERIES installation manual Tools Needed

Page 13

Tools Needed

• Power Drill

• Open End Wrenches — 3/8", 7/16", 1/2", and 9/16"

• 3/8" Drill Bit

• Hacksaw or Heavy Duty Bolt Cutters

• Small (Flat Bladed) Screwdriver

• Phillips Screwdriver/ Large

• Tape Measure

• Level

• Wire Strippers

• C-Clamps — small, medium, and large

• Center Punch

• Extra person will be helpful

YOU MAY ALSO NEED THESE ITEMS BEFORE YOU BEGIN THE INSTALLATION (Some of these items can be found in the Accessory Catalog page 37):

•Low voltage wire (RB509) will be needed to run from the transformer to the opener control board; length depends upon the distance between the transformer power supply and the opener arm. See Powering the System on page 19, and the Accessory Catalog.

•If your gate is more than 1000' away from AC ac power source you will need to use at least one Mighty Mule® 5 watt Solar Panel (FM121) to charge the 12 Volt automotive or marine type battery (not included). See the Accessory Catalog.

•If your fence post is made of wood and is less than 6" in diameter or 6" square, see page 12.

•If your fence post is larger than 6" in diameter you will need threaded rods or carriage bolts longer than 8". See page 15.

•PVC conduit.

•If you have thin walled tube or panel gates, see Recommended Reinforcement Examples on page 12.

•Depending on the type of gate, a horizontal cross member or mounting plate may be needed to mount the front of the opener and gate bracket to the gate. See page 11, step 2; page 15, step 10.

•Surge protection for transformer.

•Some types of installations require U-Bolts.

9

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 350 Installation Manual forPlace of Purchase When You Know Multiply By To Find SymbolTable of Contents Please Read this First Switch is OFF and the gate is not moving Disconnecting the OpenerEntrapment Zones for a Pull-To-Open Application For The ConsumerPull-To-Open Application II. During InstallationAny control device Within gray area III. After Installation Secondary Means of Protection Against Entrapment Entrapment Alarm UL 325 30A.1.1AInstall Warning Signs Required Safety Precautions for GatesEntrapment Protection 350 Hardware Bag Contents Tools Needed Mighty Mule 350 E-Z Gate Opener Technical SpecificationsPreparation of the Gate Installation OverviewPull-to-Open Gates Gate Opens into the Property StepRecommended Reinforcement Examples Installation of Mounting HardwarePost Bracket Assembly Closed Position Gate Bracket Mounting Examples Installing the Post Bracket Assembly and Gate BracketMounting the Opener Installation of the Closed Position StopCheck List Preparing to Activate the SystemSolar Panel and Gate Acticity Chart Powering the SystemConnecting the Battery MIghty Mule Wire Routing Important Deailed Wire Routing DiagramsImportant Information about LOW Voltage Wire Connecting the TransformerMake sure the exposed wires do not touch each other DIP Switches Connecting Solar PanelsMain DIP Switch Settings Modes DIP Switch #1 Push/Pull-to-OpenYour Mighty Mule 350 has two Limit Settings Setting the Closed Position LimitClosed Limit setting Setting Auto-Close Time Obstruction Sensitivity Potentiometer SettingRemove the Transmitter Cover Set the transmitter DIP SwitchesTeach the New Code to Control Board Memory Run the cable through PVC conduit to protect it from damage Installing the ReceiverContact Sensors safety edges Connecting Additional Safety DevicesIf not installing a contact sensor skip to next section If not installing a shadow loop skip to next section If not installing a non-contact sensor skip to next sectionNon-Contact Sensors photo beams Exit LoopIf not connecting accessories skip to next section Connecting AccessoriesAutomatic Gate Lock FM143 Mighty Mule Free Entry/Exit Loop Wiring Driveway Loops to the Mighty MuleMighty Mule Gate Opening Sensor FM138 When everything has been connected to the openerSwinging gates shall not open into public access areas Push to Open InstallationMODE2 LOCK/BEACON Setting the Open Position LimitTesting Your Open Limit Setting Power-Cycle Beep when attempt to run the unit No battery is connectedBeep with 2 seconds off Beeps with 2 seconds offGate Closes Then Opens Again on its Own Power LED GreenGate Opens Then Closes Again on its Own Charging LED RedGate Repair ServiceMail techsupport@gtoinc.com GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USAMASONRY, BRICK, or Rock etc. Columns Column Installation InformationAccessories Low Voltage Wire RB509

UL325 SERIES specifications

The GTO UL325 Series is a highly regarded line of gate operators, designed to meet the needs of both residential and commercial applications. With its commitment to safety, durability, and efficiency, the UL325 Series has set a standard in the industry for gate automation solutions.

One of the main features of the GTO UL325 Series is its robust safety mechanisms. The operators are designed to comply with the rigorous UL 325 safety standards, which is essential for ensuring user safety and preventing accidents during gate operation. This includes advanced features such as obstacle detection, which allows the system to sense when an object is in the path of the gate and stop or reverse the motion to prevent harm or damage.

The UL325 Series comes with a reliable and efficient motor that provides powerful performance while operating gates of various sizes and weights. This versatility allows it to be used for a range of gate types, including swing gates and sliding gates. The motors are also designed for quiet operation, minimizing noise disturbances in residential areas.

Additionally, the GTO UL325 Series incorporates smart technology features that enhance user experience. The built-in remote control system allows users to open and close their gates with the simple push of a button from a distance. Some models also support compatibility with smartphone apps, providing users with a modern and convenient way to control their gates from anywhere.

Durability is another characteristic of the GTO UL325 Series. Constructed with high-quality materials, these gate operators are built to withstand harsh weather conditions, making them suitable for various climates. This longevity ensures that users receive a reliable product that will serve their needs for years to come.

Another noteworthy aspect of the GTO UL325 Series is the ease of installation and maintenance. The operators are designed for straightforward installation, allowing both professionals and DIY enthusiasts to set them up with minimal hassle. Additionally, regular maintenance is simplified, with clear guidelines provided to ensure longevity and reliability.

In conclusion, the GTO UL325 Series is an exemplary choice for those seeking a reliable, safe, and technologically advanced gate operator. With its emphasis on safety, versatility, and user-friendly features, it stands out in the marketplace, making it an ideal solution for both residential and commercial gate automation needs. Investing in a GTO UL325 operator means investing in peace of mind, knowing that one has a dependable and efficient gating solution.
Top Page Image Contents