GTO UL325 SERIES installation manual Make sure the exposed wires do not touch each other

Page 26

Step 7

Strip 3/16" off the ends of the low voltage wire and twist tightly. Insert these ends to the 18 VAC terminal block located on the control board (see illustration at right). The wires can be inserted into either terminal regardless of color. Be certain not to let the exposed wires touch each other!

Tighten set screws against exposed end of wires. A dab of household petroleum jelly on each terminal will help prevent corrosion.

 

4

LOCK/BEACON

CHARGING

 

RF

POWER

 

 

LINK

 

 

 

 

 

 

 

 

 

 

 

18VAC

 

 

EXIT

SAFETY

EDGE

CYCLE

COMMON

 

GRN

 

RCVRBLK

 

RED

 

 

 

AUX

 

 

 

 

PANEL

 

 

 

 

 

 

 

OUT

 

 

 

SOLAR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Low Voltage Wire from Transformer

Step 8

At the AC outlet strip 1/2" of insulation from the ends of the low voltage wire. Attach these stripped ends to the transformer terminals.

A dab of household petroleum jelly on each terminal will help prevent corrosion.

We suggest crimping a spade tongue terminal (not provided) to the end of each wire before attaching it to the transformer.

Make sure the exposed wires do not touch each other!

Spade Tongue Terminal (not provided)

Step 9

Transformer

Plug the transformer into the electrical outlet. (Use of a surge protector with the transformer is strongly recommended.)

SURGE PROTECTOR

22

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Installation Manual for 350When You Know Multiply By To Find Symbol Place of PurchaseTable of Contents Please Read this First Disconnecting the Opener Switch is OFF and the gate is not movingFor The Consumer Entrapment Zones for a Pull-To-Open ApplicationAny control device Within gray area II. During InstallationPull-To-Open Application III. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentEntrapment Protection Required Safety Precautions for GatesInstall Warning Signs 350 Hardware Bag Contents Tools Needed Technical Specifications Mighty Mule 350 E-Z Gate OpenerPull-to-Open Gates Gate Opens into the Property Installation OverviewPreparation of the Gate StepInstallation of Mounting Hardware Recommended Reinforcement ExamplesPost Bracket Assembly Closed Position Installing the Post Bracket Assembly and Gate Bracket Gate Bracket Mounting ExamplesInstallation of the Closed Position Stop Mounting the OpenerPreparing to Activate the System Check ListPowering the System Solar Panel and Gate Acticity ChartConnecting the Battery Important Deailed Wire Routing Diagrams MIghty Mule Wire RoutingConnecting the Transformer Important Information about LOW Voltage WireMake sure the exposed wires do not touch each other Main DIP Switch Settings Modes Connecting Solar PanelsDIP Switches DIP Switch #1 Push/Pull-to-OpenClosed Limit setting Setting the Closed Position LimitYour Mighty Mule 350 has two Limit Settings Obstruction Sensitivity Potentiometer Setting Setting Auto-Close TimeTeach the New Code to Control Board Memory Set the transmitter DIP SwitchesRemove the Transmitter Cover Installing the Receiver Run the cable through PVC conduit to protect it from damageIf not installing a contact sensor skip to next section Connecting Additional Safety DevicesContact Sensors safety edges Non-Contact Sensors photo beams If not installing a non-contact sensor skip to next sectionIf not installing a shadow loop skip to next section Exit LoopAutomatic Gate Lock FM143 Connecting AccessoriesIf not connecting accessories skip to next section Wiring Driveway Loops to the Mighty Mule Mighty Mule Free Entry/Exit LoopWhen everything has been connected to the opener Mighty Mule Gate Opening Sensor FM138Push to Open Installation Swinging gates shall not open into public access areasSetting the Open Position Limit MODE2 LOCK/BEACONTesting Your Open Limit Setting Beep with 2 seconds off Beep when attempt to run the unit No battery is connectedPower-Cycle Beeps with 2 seconds offGate Opens Then Closes Again on its Own Power LED GreenGate Closes Then Opens Again on its Own Charging LED RedMail techsupport@gtoinc.com Repair ServiceGate GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USAColumn Installation Information MASONRY, BRICK, or Rock etc. ColumnsAccessories Low Voltage Wire RB509

UL325 SERIES specifications

The GTO UL325 Series is a highly regarded line of gate operators, designed to meet the needs of both residential and commercial applications. With its commitment to safety, durability, and efficiency, the UL325 Series has set a standard in the industry for gate automation solutions.

One of the main features of the GTO UL325 Series is its robust safety mechanisms. The operators are designed to comply with the rigorous UL 325 safety standards, which is essential for ensuring user safety and preventing accidents during gate operation. This includes advanced features such as obstacle detection, which allows the system to sense when an object is in the path of the gate and stop or reverse the motion to prevent harm or damage.

The UL325 Series comes with a reliable and efficient motor that provides powerful performance while operating gates of various sizes and weights. This versatility allows it to be used for a range of gate types, including swing gates and sliding gates. The motors are also designed for quiet operation, minimizing noise disturbances in residential areas.

Additionally, the GTO UL325 Series incorporates smart technology features that enhance user experience. The built-in remote control system allows users to open and close their gates with the simple push of a button from a distance. Some models also support compatibility with smartphone apps, providing users with a modern and convenient way to control their gates from anywhere.

Durability is another characteristic of the GTO UL325 Series. Constructed with high-quality materials, these gate operators are built to withstand harsh weather conditions, making them suitable for various climates. This longevity ensures that users receive a reliable product that will serve their needs for years to come.

Another noteworthy aspect of the GTO UL325 Series is the ease of installation and maintenance. The operators are designed for straightforward installation, allowing both professionals and DIY enthusiasts to set them up with minimal hassle. Additionally, regular maintenance is simplified, with clear guidelines provided to ensure longevity and reliability.

In conclusion, the GTO UL325 Series is an exemplary choice for those seeking a reliable, safe, and technologically advanced gate operator. With its emphasis on safety, versatility, and user-friendly features, it stands out in the marketplace, making it an ideal solution for both residential and commercial gate automation needs. Investing in a GTO UL325 operator means investing in peace of mind, knowing that one has a dependable and efficient gating solution.
Top Page Image Contents