GTO UL325 SERIES installation manual Low Voltage Wire RB509

Page 45

Accessories are Available From Your Retail Store (con't)

Low Voltage Wire (RB509)

The 16 gauge, multi-stranded, dual conductor Low Voltage Wire is for connecting the AC powered transformer, or the Solar Panel to the control board. Also used for the connection of accessories, such as locks, keypads, push buttons and other wired control devices. This specially designed wire is UV treated, PVC coated and ready for direct burial. Available in 1000' rolls or special lengths.

11" Push to Open Bracket (FM148)

Required when Mighty Mule® 350 gate opener(s) must push the gate open, such as on a sloping driveway or where space prevents gate(s) from opening inward (pulled open). Order two PTO brackets for conversion of a dual swing

gate installation.

Column Mount Lock Receiver (433IH)

For mounting the Automatic Gate Lock on brick columns, walls, or for other applications with limited space between gate and post.

Replacement Transformer (RB570)

Standard 18 volt AC transformer for maintaining the battery included with the Mighty Mule® gate opener. This is the only transformer approved for use with all UL325 Mighty Mule® gate opener systems.

Garage Door Receiver (RB709)

The Garage Door Receiver allows you to use the same Mighty Mule® entry transmitter (see Dual and Triple Transmitters) to operate your gate opener and your garage door opener. Compatible with most garage door openers.

Dual & Triple Button Transmitters (RB742 & RB743)

The Dual (RB742) & Triple (RB743) Button Transmitters are for remote control of multiple separate gate openers, and/or gate opener(s) and garage door opener(s) (see Garage Door Receiver). 9 Volt battery included.

If you have a question about any special order item,

just call 1-800-543-GATE!

The contents of all material available on this installation manual are copyrighted by GTO, Inc. (“GTO”), unless otherwise indicated. All rights are reserved by GTO, and content may not be reproduced, downloaded, disseminated, published, or transferred in any form or by any means, except with the prior, written permission of GTO. Any reprinting of GTO publications is by permission only. Copyright infringement is a violation of federal law.

Mighty Mule¨, E-Z Gate¨, GTO¨, are registered trademarks of GTO, Inc. America’s DIY Automatic Gate Openers is a trademark of GTO, Inc. and are the exclusive property of GTO, Inc. (“GTO”).

All rights are reserved by GTO, and these marks may not be used, in any for without the prior, written permission of GTO.

41

Image 45
Contents 350 Installation Manual forPlace of Purchase When You Know Multiply By To Find SymbolTable of Contents Please Read this First Switch is OFF and the gate is not moving Disconnecting the OpenerEntrapment Zones for a Pull-To-Open Application For The ConsumerII. During Installation Pull-To-Open ApplicationAny control device Within gray area III. After Installation Secondary Means of Protection Against Entrapment Entrapment Alarm UL 325 30A.1.1ARequired Safety Precautions for Gates Install Warning SignsEntrapment Protection 350 Hardware Bag Contents Tools Needed Mighty Mule 350 E-Z Gate Opener Technical SpecificationsPreparation of the Gate Installation OverviewPull-to-Open Gates Gate Opens into the Property StepRecommended Reinforcement Examples Installation of Mounting HardwarePost Bracket Assembly Closed Position Gate Bracket Mounting Examples Installing the Post Bracket Assembly and Gate BracketMounting the Opener Installation of the Closed Position StopCheck List Preparing to Activate the SystemSolar Panel and Gate Acticity Chart Powering the SystemConnecting the Battery MIghty Mule Wire Routing Important Deailed Wire Routing DiagramsImportant Information about LOW Voltage Wire Connecting the TransformerMake sure the exposed wires do not touch each other DIP Switches Connecting Solar PanelsMain DIP Switch Settings Modes DIP Switch #1 Push/Pull-to-OpenSetting the Closed Position Limit Your Mighty Mule 350 has two Limit SettingsClosed Limit setting Setting Auto-Close Time Obstruction Sensitivity Potentiometer SettingSet the transmitter DIP Switches Remove the Transmitter CoverTeach the New Code to Control Board Memory Run the cable through PVC conduit to protect it from damage Installing the ReceiverConnecting Additional Safety Devices Contact Sensors safety edgesIf not installing a contact sensor skip to next section If not installing a shadow loop skip to next section If not installing a non-contact sensor skip to next sectionNon-Contact Sensors photo beams Exit LoopConnecting Accessories If not connecting accessories skip to next sectionAutomatic Gate Lock FM143 Mighty Mule Free Entry/Exit Loop Wiring Driveway Loops to the Mighty MuleMighty Mule Gate Opening Sensor FM138 When everything has been connected to the openerSwinging gates shall not open into public access areas Push to Open InstallationMODE2 LOCK/BEACON Setting the Open Position LimitTesting Your Open Limit Setting Power-Cycle Beep when attempt to run the unit No battery is connectedBeep with 2 seconds off Beeps with 2 seconds offGate Closes Then Opens Again on its Own Power LED GreenGate Opens Then Closes Again on its Own Charging LED RedGate Repair ServiceMail techsupport@gtoinc.com GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USAMASONRY, BRICK, or Rock etc. Columns Column Installation InformationAccessories Low Voltage Wire RB509

UL325 SERIES specifications

The GTO UL325 Series is a highly regarded line of gate operators, designed to meet the needs of both residential and commercial applications. With its commitment to safety, durability, and efficiency, the UL325 Series has set a standard in the industry for gate automation solutions.

One of the main features of the GTO UL325 Series is its robust safety mechanisms. The operators are designed to comply with the rigorous UL 325 safety standards, which is essential for ensuring user safety and preventing accidents during gate operation. This includes advanced features such as obstacle detection, which allows the system to sense when an object is in the path of the gate and stop or reverse the motion to prevent harm or damage.

The UL325 Series comes with a reliable and efficient motor that provides powerful performance while operating gates of various sizes and weights. This versatility allows it to be used for a range of gate types, including swing gates and sliding gates. The motors are also designed for quiet operation, minimizing noise disturbances in residential areas.

Additionally, the GTO UL325 Series incorporates smart technology features that enhance user experience. The built-in remote control system allows users to open and close their gates with the simple push of a button from a distance. Some models also support compatibility with smartphone apps, providing users with a modern and convenient way to control their gates from anywhere.

Durability is another characteristic of the GTO UL325 Series. Constructed with high-quality materials, these gate operators are built to withstand harsh weather conditions, making them suitable for various climates. This longevity ensures that users receive a reliable product that will serve their needs for years to come.

Another noteworthy aspect of the GTO UL325 Series is the ease of installation and maintenance. The operators are designed for straightforward installation, allowing both professionals and DIY enthusiasts to set them up with minimal hassle. Additionally, regular maintenance is simplified, with clear guidelines provided to ensure longevity and reliability.

In conclusion, the GTO UL325 Series is an exemplary choice for those seeking a reliable, safe, and technologically advanced gate operator. With its emphasis on safety, versatility, and user-friendly features, it stands out in the marketplace, making it an ideal solution for both residential and commercial gate automation needs. Investing in a GTO UL325 operator means investing in peace of mind, knowing that one has a dependable and efficient gating solution.