GTO UL325 SERIES Remove the Transmitter Cover, Set the transmitter DIP Switches

Page 30

Setting Your Personal Transmitter Code

All GTO transmitters are set to a standard code at the factory and are ready to operate your Mighty Mule® Gate Opener®. For your safety and security, however, we strongly recommend that you replace the factory setting with your own personal code. Follow the directions below:

1. Remove the Transmitter Cover

On the back of the transmitter use a small phillips head screw driver to remove the two screws on the sides of the visor clip and separate the front cover from the transmitter. With the front cover removed, the battery and the DIP switches will be exposed. To set a new code, use a small screwdriver to move the switches.

2. Set the transmitter DIP Switches

There are nine (9) transmitter DIP switches; each can be placed in three different positions (+, 0, –). DO NOT set all the switches in the same position, such as all +, all 0, or all –. Once the DIP switches have been set to a personal code, replace and close the access cover.

WARNING: No other adjustments should be made inside the transmitter.

LED

 

+

1

 

0

2

–

3

 

 

4

A23S

5

EC

 

 

6

ALKALINE

 

7

 

 

8

 

 

9

 

 

E

 

BA

12VER

 

 

TT

 

 

Y

+1 2 3 4 5 6 7 8 9 0

ECE

3. “Teach” the New Code to Control Board Memory

A. Press and hold transmitter button.

B. Press and hold the LEARN REMOTE button on

the control board until it beeps.

C. Release transmitter button.

D. Release LEARN REMOTE button. The new code

STATUS

is stored in control board memory.

CHARGING

POWER

MIN MAX

STALL FORCE

OFF 120

CLOSE TIME

SET LEARN

LIMIT REMOTE

 

 

 

ON

PULL-PUSH

1

 

 

2

 

 

 

MODE1

3

 

 

 

MODE2

4

 

 

 

LOCK/BEACON

 

 

 

 

 

RF

LEARN REMOTE Button

LINK

18VAC

SOLAR PANEL

EXIT

SAFETY

EDGE

CYCLE

COMMON

GRN

BLK

RED

 

 

 

RECR

26

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Installation Manual for 350When You Know Multiply By To Find Symbol Place of PurchaseTable of Contents Please Read this First Disconnecting the Opener Switch is OFF and the gate is not movingFor The Consumer Entrapment Zones for a Pull-To-Open ApplicationII. During Installation Pull-To-Open ApplicationAny control device Within gray area III. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentRequired Safety Precautions for Gates Install Warning SignsEntrapment Protection 350 Hardware Bag Contents Tools Needed Technical Specifications Mighty Mule 350 E-Z Gate OpenerPull-to-Open Gates Gate Opens into the Property Installation OverviewPreparation of the Gate StepInstallation of Mounting Hardware Recommended Reinforcement ExamplesPost Bracket Assembly Closed Position Installing the Post Bracket Assembly and Gate Bracket Gate Bracket Mounting ExamplesInstallation of the Closed Position Stop Mounting the OpenerPreparing to Activate the System Check ListPowering the System Solar Panel and Gate Acticity ChartConnecting the Battery Important Deailed Wire Routing Diagrams MIghty Mule Wire RoutingConnecting the Transformer Important Information about LOW Voltage WireMake sure the exposed wires do not touch each other Main DIP Switch Settings Modes Connecting Solar PanelsDIP Switches DIP Switch #1 Push/Pull-to-OpenSetting the Closed Position Limit Your Mighty Mule 350 has two Limit SettingsClosed Limit setting Obstruction Sensitivity Potentiometer Setting Setting Auto-Close TimeSet the transmitter DIP Switches Remove the Transmitter CoverTeach the New Code to Control Board Memory Installing the Receiver Run the cable through PVC conduit to protect it from damageConnecting Additional Safety Devices Contact Sensors safety edgesIf not installing a contact sensor skip to next section Non-Contact Sensors photo beams If not installing a non-contact sensor skip to next sectionIf not installing a shadow loop skip to next section Exit LoopConnecting Accessories If not connecting accessories skip to next sectionAutomatic Gate Lock FM143 Wiring Driveway Loops to the Mighty Mule Mighty Mule Free Entry/Exit LoopWhen everything has been connected to the opener Mighty Mule Gate Opening Sensor FM138Push to Open Installation Swinging gates shall not open into public access areasSetting the Open Position Limit MODE2 LOCK/BEACONTesting Your Open Limit Setting Beep with 2 seconds off Beep when attempt to run the unit No battery is connectedPower-Cycle Beeps with 2 seconds offGate Opens Then Closes Again on its Own Power LED GreenGate Closes Then Opens Again on its Own Charging LED RedMail techsupport@gtoinc.com Repair ServiceGate GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USAColumn Installation Information MASONRY, BRICK, or Rock etc. ColumnsAccessories Low Voltage Wire RB509

UL325 SERIES specifications

The GTO UL325 Series is a highly regarded line of gate operators, designed to meet the needs of both residential and commercial applications. With its commitment to safety, durability, and efficiency, the UL325 Series has set a standard in the industry for gate automation solutions.

One of the main features of the GTO UL325 Series is its robust safety mechanisms. The operators are designed to comply with the rigorous UL 325 safety standards, which is essential for ensuring user safety and preventing accidents during gate operation. This includes advanced features such as obstacle detection, which allows the system to sense when an object is in the path of the gate and stop or reverse the motion to prevent harm or damage.

The UL325 Series comes with a reliable and efficient motor that provides powerful performance while operating gates of various sizes and weights. This versatility allows it to be used for a range of gate types, including swing gates and sliding gates. The motors are also designed for quiet operation, minimizing noise disturbances in residential areas.

Additionally, the GTO UL325 Series incorporates smart technology features that enhance user experience. The built-in remote control system allows users to open and close their gates with the simple push of a button from a distance. Some models also support compatibility with smartphone apps, providing users with a modern and convenient way to control their gates from anywhere.

Durability is another characteristic of the GTO UL325 Series. Constructed with high-quality materials, these gate operators are built to withstand harsh weather conditions, making them suitable for various climates. This longevity ensures that users receive a reliable product that will serve their needs for years to come.

Another noteworthy aspect of the GTO UL325 Series is the ease of installation and maintenance. The operators are designed for straightforward installation, allowing both professionals and DIY enthusiasts to set them up with minimal hassle. Additionally, regular maintenance is simplified, with clear guidelines provided to ensure longevity and reliability.

In conclusion, the GTO UL325 Series is an exemplary choice for those seeking a reliable, safe, and technologically advanced gate operator. With its emphasis on safety, versatility, and user-friendly features, it stands out in the marketplace, making it an ideal solution for both residential and commercial gate automation needs. Investing in a GTO UL325 operator means investing in peace of mind, knowing that one has a dependable and efficient gating solution.
Top Page Image Contents