GTO UL325 SERIES installation manual Powering the System, Solar Panel and Gate Acticity Chart

Page 22

Powering the System

IMPORTANT:

•The Mighty Mule 350 is designed and intended for use with a 12 Volt automotive or marine type battery.

The battery must be placed inside a weatherproof case and located within 6 feet of the opener arm. The 10 foot harness supplied connects the battery to the opener arm.

•The battery charge is maintained by the 18 Volt transformer included or by using optional solar panel(s). The transformer or solar panel is connected to the opener arm control board using low voltage, 16 gauge, dual conductor, multi-stranded, direct burial wire (FM509) (seepage 23 and the Accessory Catalog).

•All low voltage wire used with the Mighty Mule® Gate Opener must be 16 gauge dual conductor, multi-stranded, direct burial wire (see page 20 and the Accessory Catalog). Do not run more than 1000 feet of wire.

•The transformer is designed and intended for indoor use. If the transformer can be plugged only into an outside electrical outlet, a weatherproof cover or housing (available at local electrical supply stores) must be used.

•If your gate is more than 1000 ft. from an ac power source, you will need to use at least one 5 watt Solar

Panel to charge the battery (see Accessory Catalog). Refer to the Solar Panels and Gate Activity chart below.

NEVER USE TRANSFORMER AND SOLAR PANEL(S) AT THE SAME TIME

– it willl damage the control board –

Solar Panel and Gate Acticity Chart

The table and map illustrate the maximum number of gate cycles to expect per day in a

particular area when using from 5 to 30 watts of solar charging power. (see Accessory Catalog). The figures shown are for winter (minimum

sunlight) and do not account for the use of any accessory items.

Accessories connected to your system will draw additional power from the battery and will require additional solar panels.

NOTE: A maximum of 30 watts of solar charging power can be connected to the Mighty Mule® Gate Opener. Consult Solar Panel Installation Instructions for further information.

Single Gate Winter Ratings

Zone 1

Zone 2

Zone 3

 

 

 

 

12 v single gate (5 watts) solar charger

4

8

13

12 v single gate (10 watts) solar charger

8

16

26

12 v single gate (15 watts) solar charger

11

20

30

12 v single gate (20 watts) solar charger

14

28

38

12 v single gate (25 watts) solar charger

17

36

46

12 v single gate (30 watts) solar charger

20

44

54

 

 

 

 

18

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Installation Manual for 350When You Know Multiply By To Find Symbol Place of PurchaseTable of Contents Please Read this First Disconnecting the Opener Switch is OFF and the gate is not movingFor The Consumer Entrapment Zones for a Pull-To-Open ApplicationPull-To-Open Application II. During InstallationAny control device Within gray area III. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentInstall Warning Signs Required Safety Precautions for GatesEntrapment Protection 350 Hardware Bag Contents Tools Needed Technical Specifications Mighty Mule 350 E-Z Gate OpenerPull-to-Open Gates Gate Opens into the Property Installation OverviewPreparation of the Gate StepInstallation of Mounting Hardware Recommended Reinforcement ExamplesPost Bracket Assembly Closed Position Installing the Post Bracket Assembly and Gate Bracket Gate Bracket Mounting ExamplesInstallation of the Closed Position Stop Mounting the OpenerPreparing to Activate the System Check ListPowering the System Solar Panel and Gate Acticity ChartConnecting the Battery Important Deailed Wire Routing Diagrams MIghty Mule Wire RoutingConnecting the Transformer Important Information about LOW Voltage WireMake sure the exposed wires do not touch each other Main DIP Switch Settings Modes Connecting Solar PanelsDIP Switches DIP Switch #1 Push/Pull-to-OpenYour Mighty Mule 350 has two Limit Settings Setting the Closed Position LimitClosed Limit setting Obstruction Sensitivity Potentiometer Setting Setting Auto-Close TimeRemove the Transmitter Cover Set the transmitter DIP SwitchesTeach the New Code to Control Board Memory Installing the Receiver Run the cable through PVC conduit to protect it from damageContact Sensors safety edges Connecting Additional Safety DevicesIf not installing a contact sensor skip to next section Non-Contact Sensors photo beams If not installing a non-contact sensor skip to next sectionIf not installing a shadow loop skip to next section Exit LoopIf not connecting accessories skip to next section Connecting AccessoriesAutomatic Gate Lock FM143 Wiring Driveway Loops to the Mighty Mule Mighty Mule Free Entry/Exit LoopWhen everything has been connected to the opener Mighty Mule Gate Opening Sensor FM138Push to Open Installation Swinging gates shall not open into public access areasSetting the Open Position Limit MODE2 LOCK/BEACONTesting Your Open Limit Setting Beep with 2 seconds off Beep when attempt to run the unit No battery is connectedPower-Cycle Beeps with 2 seconds offGate Opens Then Closes Again on its Own Power LED GreenGate Closes Then Opens Again on its Own Charging LED RedMail techsupport@gtoinc.com Repair ServiceGate GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USAColumn Installation Information MASONRY, BRICK, or Rock etc. ColumnsAccessories Low Voltage Wire RB509

UL325 SERIES specifications

The GTO UL325 Series is a highly regarded line of gate operators, designed to meet the needs of both residential and commercial applications. With its commitment to safety, durability, and efficiency, the UL325 Series has set a standard in the industry for gate automation solutions.

One of the main features of the GTO UL325 Series is its robust safety mechanisms. The operators are designed to comply with the rigorous UL 325 safety standards, which is essential for ensuring user safety and preventing accidents during gate operation. This includes advanced features such as obstacle detection, which allows the system to sense when an object is in the path of the gate and stop or reverse the motion to prevent harm or damage.

The UL325 Series comes with a reliable and efficient motor that provides powerful performance while operating gates of various sizes and weights. This versatility allows it to be used for a range of gate types, including swing gates and sliding gates. The motors are also designed for quiet operation, minimizing noise disturbances in residential areas.

Additionally, the GTO UL325 Series incorporates smart technology features that enhance user experience. The built-in remote control system allows users to open and close their gates with the simple push of a button from a distance. Some models also support compatibility with smartphone apps, providing users with a modern and convenient way to control their gates from anywhere.

Durability is another characteristic of the GTO UL325 Series. Constructed with high-quality materials, these gate operators are built to withstand harsh weather conditions, making them suitable for various climates. This longevity ensures that users receive a reliable product that will serve their needs for years to come.

Another noteworthy aspect of the GTO UL325 Series is the ease of installation and maintenance. The operators are designed for straightforward installation, allowing both professionals and DIY enthusiasts to set them up with minimal hassle. Additionally, regular maintenance is simplified, with clear guidelines provided to ensure longevity and reliability.

In conclusion, the GTO UL325 Series is an exemplary choice for those seeking a reliable, safe, and technologically advanced gate operator. With its emphasis on safety, versatility, and user-friendly features, it stands out in the marketplace, making it an ideal solution for both residential and commercial gate automation needs. Investing in a GTO UL325 operator means investing in peace of mind, knowing that one has a dependable and efficient gating solution.
Top Page Image Contents