GTO UL325 SERIES Gate Closes Then Opens Again on its Own, Gate Opens Then Closes Again on its Own

Page 41

2.STATUS LED (LED1): While the unit is IDLE:

1 blink with 2 seconds off:

Free Exit terminal is shorted to common.

2 blink with 2 seconds off:

Safety terminal is shorted to common.

3 blink with 2 seconds off:

Edge terminal is shorted to common.

4 blink with 2 seconds off:

Cycle terminal is shorted to common. LEARN LIMIT Mode:

This LED will turn on when the ‘LEARN-LIMIT’ button is pressed. It will turn off after 3 seconds indicating that it has entered the learn limit mode (if not at the retracted limit) or cleared the previous learned limit (if at retracted limit). See "Setting Closed Position" section on page 24.

Whenever there is a change in state at any of the inputs this LED will blink once.

3.POWER LED (Green):

ON: AC power or solar power is presented.

OFF: NO AC power or solar power is presented.

4.CHARGING LED (Red):

Continuously ON: Fast charging mode. (~1.5 Amps charging current).

Blinking (two blinks per second): Soak charge. Enter this mode after fast charging. The battery is almost at full charge in this mode.

Slow blinking (one blink per second): Float charge. In this mode when the battery is fully charged.

The Gate CLOSES Then Opens Again on its Own:

1.Check the position of the mounting brackets and readjust if necessary.

2.Check the gate for binding or hinge damage.

The Gate OPENS Then Closes Again on its Own:

1.Check the position of the mounting brackets and readjust if necessary.

2.Check the gate for binding or hinge damage.

VOLTAGE RATINGS

18 Vac Transformer____________________________18.0 to 22.0 Vac

5 W Solar panel (single)________________________18.0 to 22.0 Vdc 300 mA

measure voltage at panel and control box.

12 V Battery_ ________________________________12.0 to 13.5 Vdc 7.0 Ah

Charging circuit ______________________________12.0 to 14.8 Vdc

measure voltage with battery connected

37

Page 40 Page 42
Image 41
Page 40 Page 42
Contents 350 Installation Manual forPlace of Purchase When You Know Multiply By To Find SymbolTable of Contents Please Read this First Switch is OFF and the gate is not moving Disconnecting the OpenerEntrapment Zones for a Pull-To-Open Application For The ConsumerAny control device Within gray area II. During InstallationPull-To-Open Application III. After Installation Secondary Means of Protection Against Entrapment Entrapment Alarm UL 325 30A.1.1AEntrapment Protection Required Safety Precautions for GatesInstall Warning Signs 350 Hardware Bag Contents Tools Needed Mighty Mule 350 E-Z Gate Opener Technical SpecificationsPreparation of the Gate Installation OverviewPull-to-Open Gates Gate Opens into the Property StepRecommended Reinforcement Examples Installation of Mounting HardwarePost Bracket Assembly Closed Position Gate Bracket Mounting Examples Installing the Post Bracket Assembly and Gate BracketMounting the Opener Installation of the Closed Position StopCheck List Preparing to Activate the SystemSolar Panel and Gate Acticity Chart Powering the SystemConnecting the Battery MIghty Mule Wire Routing Important Deailed Wire Routing DiagramsImportant Information about LOW Voltage Wire Connecting the TransformerMake sure the exposed wires do not touch each other DIP Switches Connecting Solar PanelsMain DIP Switch Settings Modes DIP Switch #1 Push/Pull-to-OpenClosed Limit setting Setting the Closed Position LimitYour Mighty Mule 350 has two Limit Settings Setting Auto-Close Time Obstruction Sensitivity Potentiometer SettingTeach the New Code to Control Board Memory Set the transmitter DIP SwitchesRemove the Transmitter Cover Run the cable through PVC conduit to protect it from damage Installing the ReceiverIf not installing a contact sensor skip to next section Connecting Additional Safety DevicesContact Sensors safety edges If not installing a shadow loop skip to next section If not installing a non-contact sensor skip to next sectionNon-Contact Sensors photo beams Exit LoopAutomatic Gate Lock FM143 Connecting AccessoriesIf not connecting accessories skip to next section Mighty Mule Free Entry/Exit Loop Wiring Driveway Loops to the Mighty MuleMighty Mule Gate Opening Sensor FM138 When everything has been connected to the openerSwinging gates shall not open into public access areas Push to Open InstallationMODE2 LOCK/BEACON Setting the Open Position LimitTesting Your Open Limit Setting Power-Cycle Beep when attempt to run the unit No battery is connectedBeep with 2 seconds off Beeps with 2 seconds offGate Closes Then Opens Again on its Own Power LED GreenGate Opens Then Closes Again on its Own Charging LED RedGate Repair ServiceMail techsupport@gtoinc.com GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USAMASONRY, BRICK, or Rock etc. Columns Column Installation InformationAccessories Low Voltage Wire RB509

UL325 SERIES specifications

The GTO UL325 Series is a highly regarded line of gate operators, designed to meet the needs of both residential and commercial applications. With its commitment to safety, durability, and efficiency, the UL325 Series has set a standard in the industry for gate automation solutions.

One of the main features of the GTO UL325 Series is its robust safety mechanisms. The operators are designed to comply with the rigorous UL 325 safety standards, which is essential for ensuring user safety and preventing accidents during gate operation. This includes advanced features such as obstacle detection, which allows the system to sense when an object is in the path of the gate and stop or reverse the motion to prevent harm or damage.

The UL325 Series comes with a reliable and efficient motor that provides powerful performance while operating gates of various sizes and weights. This versatility allows it to be used for a range of gate types, including swing gates and sliding gates. The motors are also designed for quiet operation, minimizing noise disturbances in residential areas.

Additionally, the GTO UL325 Series incorporates smart technology features that enhance user experience. The built-in remote control system allows users to open and close their gates with the simple push of a button from a distance. Some models also support compatibility with smartphone apps, providing users with a modern and convenient way to control their gates from anywhere.

Durability is another characteristic of the GTO UL325 Series. Constructed with high-quality materials, these gate operators are built to withstand harsh weather conditions, making them suitable for various climates. This longevity ensures that users receive a reliable product that will serve their needs for years to come.

Another noteworthy aspect of the GTO UL325 Series is the ease of installation and maintenance. The operators are designed for straightforward installation, allowing both professionals and DIY enthusiasts to set them up with minimal hassle. Additionally, regular maintenance is simplified, with clear guidelines provided to ensure longevity and reliability.

In conclusion, the GTO UL325 Series is an exemplary choice for those seeking a reliable, safe, and technologically advanced gate operator. With its emphasis on safety, versatility, and user-friendly features, it stands out in the marketplace, making it an ideal solution for both residential and commercial gate automation needs. Investing in a GTO UL325 operator means investing in peace of mind, knowing that one has a dependable and efficient gating solution.
Top Page Image Contents