GTO UL325 SERIES installation manual Setting the Open Position Limit, MODE2 LOCK/BEACON

Page 38

Step 3

With the gate in the fully closed position and the opener retracted, swing the opener to the gate. Mark reference points for bolt holes on gate cross member through middle of gate bracket slots. The opener must be level. (Some vertical adjustment

is possible by sliding the post bracket assembly up and down.) Drill 3/8" holes into the gate cross member as marked. Fasten gate bracket to cross member using (2) 3/8" x 3" bolts, washers, lock washers, and nuts. Attach the opener to the post bracket assembly and gate bracket using clevis pins, bushings, and hairpins clips.

Fence Post

Gate Post and Gate Cross Member

 

(In Closed Position)

LEVEL

Operator

LEVEL

POST PIVOT BRACKET level with the horizontal surface of the GATE BRACKET

LEVEL

OFF 120

CLOSE TIME

SET LEARN LIMIT REMOTE

Step 4

Make sure the control box power switch is OFF. Use a small screwdriver to move the Number 1 DIP switch from the factory setting (OFF / Pull-To-Open) to ON for Push-To-Open. Turn power switch ON. The control board is now configured to push the gate open.

15

 

1

ON

2

 

3

 

4

 

AUX OUT

PULL-PUSHCHARGING

MODE1 POWER

 

 

 

 

MODE2

 

 

 

 

LOCK/BEACON

 

 

 

 

LINK

 

 

 

 

18VAC

EXIT

SAFETY

EDGE

CYCLE

SOLAR

PANEL

 

ON

PULL-PUSH

1

 

2

 

 

MODE1

 

 

3

 

 

MODE2

 

 

4

 

 

LOCK/BEACON

 

 

 

 

 

 

RF

COMMON

GRN

RCVRBLK

RED

Setting the Open Position Limit

Step 1

Confirm that the power switch is in the ON position, and the gate is in the CLOSED POSITION.

Step 2

Activate your opener by pressing the entry transmitter button. Your gate should now be moving from the closed position toward the open position. Prepare to STOP gate by pressing the entry transmitter button again when the gate reaches the desired open position. This step may be repeated until desired open position is achieved. Once the desired OPEN position has been achieved, proceed to Step 3.

34

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Installation Manual for 350When You Know Multiply By To Find Symbol Place of PurchaseTable of Contents Please Read this First Disconnecting the Opener Switch is OFF and the gate is not movingFor The Consumer Entrapment Zones for a Pull-To-Open ApplicationAny control device Within gray area II. During InstallationPull-To-Open Application III. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentEntrapment Protection Required Safety Precautions for GatesInstall Warning Signs 350 Hardware Bag Contents Tools Needed Technical Specifications Mighty Mule 350 E-Z Gate OpenerPull-to-Open Gates Gate Opens into the Property Installation OverviewPreparation of the Gate StepInstallation of Mounting Hardware Recommended Reinforcement ExamplesPost Bracket Assembly Closed Position Installing the Post Bracket Assembly and Gate Bracket Gate Bracket Mounting ExamplesInstallation of the Closed Position Stop Mounting the OpenerPreparing to Activate the System Check ListPowering the System Solar Panel and Gate Acticity ChartConnecting the Battery Important Deailed Wire Routing Diagrams MIghty Mule Wire RoutingConnecting the Transformer Important Information about LOW Voltage WireMake sure the exposed wires do not touch each other Main DIP Switch Settings Modes Connecting Solar PanelsDIP Switches DIP Switch #1 Push/Pull-to-OpenClosed Limit setting Setting the Closed Position LimitYour Mighty Mule 350 has two Limit Settings Obstruction Sensitivity Potentiometer Setting Setting Auto-Close TimeTeach the New Code to Control Board Memory Set the transmitter DIP SwitchesRemove the Transmitter Cover Installing the Receiver Run the cable through PVC conduit to protect it from damageIf not installing a contact sensor skip to next section Connecting Additional Safety DevicesContact Sensors safety edges Non-Contact Sensors photo beams If not installing a non-contact sensor skip to next sectionIf not installing a shadow loop skip to next section Exit LoopAutomatic Gate Lock FM143 Connecting AccessoriesIf not connecting accessories skip to next section Wiring Driveway Loops to the Mighty Mule Mighty Mule Free Entry/Exit LoopWhen everything has been connected to the opener Mighty Mule Gate Opening Sensor FM138Push to Open Installation Swinging gates shall not open into public access areasSetting the Open Position Limit MODE2 LOCK/BEACONTesting Your Open Limit Setting Beep with 2 seconds off Beep when attempt to run the unit No battery is connectedPower-Cycle Beeps with 2 seconds offGate Opens Then Closes Again on its Own Power LED GreenGate Closes Then Opens Again on its Own Charging LED RedMail techsupport@gtoinc.com Repair ServiceGate GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USAColumn Installation Information MASONRY, BRICK, or Rock etc. ColumnsAccessories Low Voltage Wire RB509

UL325 SERIES specifications

The GTO UL325 Series is a highly regarded line of gate operators, designed to meet the needs of both residential and commercial applications. With its commitment to safety, durability, and efficiency, the UL325 Series has set a standard in the industry for gate automation solutions.

One of the main features of the GTO UL325 Series is its robust safety mechanisms. The operators are designed to comply with the rigorous UL 325 safety standards, which is essential for ensuring user safety and preventing accidents during gate operation. This includes advanced features such as obstacle detection, which allows the system to sense when an object is in the path of the gate and stop or reverse the motion to prevent harm or damage.

The UL325 Series comes with a reliable and efficient motor that provides powerful performance while operating gates of various sizes and weights. This versatility allows it to be used for a range of gate types, including swing gates and sliding gates. The motors are also designed for quiet operation, minimizing noise disturbances in residential areas.

Additionally, the GTO UL325 Series incorporates smart technology features that enhance user experience. The built-in remote control system allows users to open and close their gates with the simple push of a button from a distance. Some models also support compatibility with smartphone apps, providing users with a modern and convenient way to control their gates from anywhere.

Durability is another characteristic of the GTO UL325 Series. Constructed with high-quality materials, these gate operators are built to withstand harsh weather conditions, making them suitable for various climates. This longevity ensures that users receive a reliable product that will serve their needs for years to come.

Another noteworthy aspect of the GTO UL325 Series is the ease of installation and maintenance. The operators are designed for straightforward installation, allowing both professionals and DIY enthusiasts to set them up with minimal hassle. Additionally, regular maintenance is simplified, with clear guidelines provided to ensure longevity and reliability.

In conclusion, the GTO UL325 Series is an exemplary choice for those seeking a reliable, safe, and technologically advanced gate operator. With its emphasis on safety, versatility, and user-friendly features, it stands out in the marketplace, making it an ideal solution for both residential and commercial gate automation needs. Investing in a GTO UL325 operator means investing in peace of mind, knowing that one has a dependable and efficient gating solution.
Top Page Image Contents