Chamberlain 8200 1/2 HP owner manual Example, One-piece door without track Jamb hardware, =12

Page 13

ONE-PIECE Door Without Track

Read the Safety Instructions on page 12. They also apply to doors without tracks.

•Close the door and mark the inside vertical centerline of your garage door. Extend the line onto the header wall above door.

If headroom clearance is minimal, you can install the header bracket on the ceiling. See page 14.

•If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag screws (not supplied) to securely fasten the 2x4 to structural supports as shown.

Unfinished

Header Wall

Vertical

Ceiling

 

 

 

 

Centerline

2x4

 

 

Structural

Supports

2x4

Vertical

Centerline of

Garage Door

OPTIONAL CEILING MOUNT

FOR HEADER BRACKET

 

Header Wall

 

Highest Point

 

of Travel

Door

 

Jamb

Distance

Hardware

 

One-piece door without track

jamb hardware

•Open your door to the highest point of travel as shown. Measure the distance from the top of the door to the floor. Subtract the actual height of the door. Add 8" to the remainder. (See Example.)

•Close the door and draw an intersecting horizontal line on the header wall at the determined height.

If the total number of inches exceeds the height available in your garage, use the maximum height possible, or refer to page 14 for ceiling installation.

Header

Highest Point

Wall

of Travel

Door

Distance

 

Pivot

 

One-piece door without track

pivot hardware

Example

Distance from top of door

 

 

(at highest point of travel) to floor

...........................92"

Actual height of door

-88"

Remainder

 

4"

Add

+8"

Bracket height on header wall

=12"

(Measure UP from top of CLOSED door.)

Proceed to Step 2, page 14.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Garage Door Opener Model 8200 Series Contents Start by reviewing these important safety alert symbolsAssembly section pages 8 Installation section pages 11Youll Need Tools Closed Position Sectional Door InstallationOne-Piece Door without Track ONE-PIECE Door InstallationOne-Piece Door With Track Security Carton InventoryAssembly Assembly Step Assembly Section Pages 8Attach the Belt Pulley Bracket Right WrongFaster the T-rail to the Opener Install the Trolley on the T-railCheck to make sure the belt is not twisted Install the Belt & Set the Belt TensionDo not use any tools To attach the belt cap retainer Attach the Belt Cap RetainerDetermine Header Bracket Location Installation Section Pages 12 Installation StepSectional Door ONE-PIECE Door With Track Proceed to ,One-piece door without track Jamb hardware ExampleOne-piece door without track Pivot hardware =12Fasten the Header Bracket to the Wall Install the Header BracketFasten the Header Bracket to the Ceiling Attach the T-rail to the Header Bracket Sectional Door & ONE-PIECE Door with Track Position the OpenerRaise the opener onto a stepladder Grease the top Underside of the rail Hang the OpenerSurface where Trolley slides with rail greaseOutside Keylock Accessory Connections Install the Multi-Function Door Control PanelTo opener terminal screws white to 2 white/red to 32 explains how to use the door control Install the Lights and the LensesSee Safety Reversing Sensor Instructions beginning on Reverse the procedure to remove the lensesElectrical Requirements Permanent Wiring ConnectionFacing the door from inside the garage Protector SystemInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Fasten Door Bracket Sectional Door Installation ProcedureHeader Wall Sectional Doors Only Connect Door Arm to TrolleyHole Alignment Alternative All ONE-PIECE Doors Adjustment Procedures for One-Piece DoorsAdjust the UP and Down Limits Adjustment Section Pages 28 Adjustment StepHow and When to Adjust the Limits How and When to Adjust the Forces Adjust the ForceTest the Down close force Test the UP open forceImportant safety check Test the Safety Reverse SystemTest the Protector System Limit and Force Adjustment Controls Maintenance ScheduleRemote control battery Care of Your OpenerOperation of the Multi-Function Door Control Operation of Your OpenerOutside Keylock or Keyless Entry Manual disconnect Position To open the door manuallyReceiver and Remote Control Programming Situation Probable Cause & Solution Having a Problem?Door control, a short under the staples, or a broken wire Are the wiring connections correct? Review ,Bulb if regular bulb burns out Is the Light feature on? Turn it offRail Assembly Parts Repair PartsInstallation Parts Complete with Opener Assembly PartsAccessories Available for your Opener Index Chamberlain Service Is on Call

8200 1/2 HP specifications

The Chamberlain 8200 is a robust and efficient garage door opener that combines power, reliability, and advanced technology to provide homeowners with a seamless experience. With its 1/2 HP motor, this opener is designed to handle sectional doors weighing up to 500 pounds, making it suitable for a variety of garage doors.

One of the standout features of the Chamberlain 8200 is its strong motor, which ensures smooth and quiet operation. This is particularly important for homeowners who have living spaces adjacent to the garage, as the reduced noise levels contribute to a more comfortable environment. The motor is also designed for durability and long-lasting performance, ensuring that it will consistently meet the needs of the user over time.

The Chamberlain 8200 comes equipped with the innovative MyQ technology, which enables users to control their garage door opener remotely via a smartphone app. This feature not only provides convenience but also enhances security, allowing homeowners to monitor and manage their garage door from anywhere. Whether you’re on vacation or simply at work, the ability to check the status of your garage door gives peace of mind.

Safety is another priority with the Chamberlain 8200, which includes features such as the patented Security+ 2.0 technology. This system ensures that your garage door opener transmits a new code every time the remote control is used, significantly reducing the risk of unauthorized access. Additionally, the opener is equipped with safety sensors that detect any obstructions in the door's path, preventing accidents or injuries.

Installation of the Chamberlain 8200 is straightforward, thanks to its detailed instructions and user-friendly design. The unit is compatible with a variety of garage door types and can easily integrate with existing door systems.

Overall, the Chamberlain 8200 1/2 HP garage door opener stands out as a powerful, technologically advanced solution for homeowners seeking convenience and security. Its blend of performance, innovative features, and user-friendly design makes it a top choice for modern garage door automation. Whether you are looking to upgrade your current system or installing a new opener, the Chamberlain 8200 promises reliability and peace of mind.
Top Page Image Contents