Chamberlain 8200 1/2 HP How and When to Adjust the Forces, Test the Down close force

Page 29

Adjustment Step 2

Adjust the Force

Force adjustment controls are located on the right panel of the opener. Force adjustment settings regulate the amount of power required to open and close the door.

The door will stop in the up direction if anything interferes with its travel. The door will reverse in the down direction if anything interferes with its travel (including binding or unbalanced doors).

If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weather conditions can affect the door movement, so occasional adjustment may be needed.

The maximum force adjustment range is 260 degrees, about 3/4 of a complete turn. Do not force controls beyond that point. Turn force adjustment controls with a screwdriver.

9

1

9

1

7

3

7

3

5

 

 

5

KGKG

Force Adjustment Label

WARNING

Too much force on the door will interfere with the proper operation of the safety reverse system. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond the minimum amount required to close the door. Do not use the force adjustments to compensate for a binding or sticking garage door. Test the safety reverse system following all adjustments to force levels. See page 30.

Force

Adjustment

Controls

1

2

 

 

3

 

9

1

9

1

 

7

3

7

3

 

5

 

 

5

KGKG

Right Panel

of Opener

How and When to Adjust the Forces

Test the DOWN (close) force

Grasp the door bottom when the door is about halfway through DOWN (close) travel. The door should reverse. Reversal halfway through down travel does not guarantee reversal on a one-inch obstruction. See page 30. If the door is hard to hold or doesn't reverse, decrease the DOWN (close) force by turning the control counterclockwise.

Make 10 degree turn adjustments until the door reverses normally. After each adjustment, run the opener through a complete cycle.

Test the UP (open) force

Grasp the door bottom when the door is about halfway through UP (open) travel. The door should stop. If the door is hard to hold or doesn't stop, decrease UP (open) force by turning the control counterclockwise.

Make 10 degree turn adjustments until the door stops easily. After each adjustment, run the opener through a complete travel cycle.

If the door doesn't open at least 5 feet

Increase UP (Open) force by turning the control clockwise. Make 10 degree turn adjustments until door opens completely. Re-adjust the UP limit if necessary. After each adjustment, run the opener through a complete travel cycle.

If the door reverses during the down (close) cycle and the opener lights aren't flashing

Increase DOWN (close) force by turning the control clockwise. Make 10 degree turn adjustments until the door completes a close cycle. After each adjustment, run the opener through a complete travel cycle. Do not increase the force beyond the minimum amount required to close the door.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Garage Door Opener Model 8200 Series Contents Start by reviewing these important safety alert symbolsAssembly section pages 8 Installation section pages 11Youll Need Tools Closed Position Sectional Door InstallationOne-Piece Door With Track ONE-PIECE Door InstallationOne-Piece Door without Track Security Carton InventoryAssembly Assembly Step Assembly Section Pages 8Attach the Belt Pulley Bracket Right WrongFaster the T-rail to the Opener Install the Trolley on the T-railDo not use any tools Install the Belt & Set the Belt TensionCheck to make sure the belt is not twisted To attach the belt cap retainer Attach the Belt Cap RetainerDetermine Header Bracket Location Installation Section Pages 12 Installation StepSectional Door ONE-PIECE Door With Track Proceed to ,One-piece door without track Jamb hardware ExampleOne-piece door without track Pivot hardware =12Fasten the Header Bracket to the Ceiling Install the Header BracketFasten the Header Bracket to the Wall Attach the T-rail to the Header Bracket Raise the opener onto a stepladder Position the OpenerSectional Door & ONE-PIECE Door with Track Grease the top Underside of the rail Hang the OpenerSurface where Trolley slides with rail greaseTo opener terminal screws white to 2 white/red to Install the Multi-Function Door Control PanelOutside Keylock Accessory Connections 32 explains how to use the door control Install the Lights and the LensesSee Safety Reversing Sensor Instructions beginning on Reverse the procedure to remove the lensesElectrical Requirements Permanent Wiring ConnectionFacing the door from inside the garage Protector SystemInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Fasten Door Bracket Sectional Door Installation ProcedureHeader Wall Hole Alignment Alternative Connect Door Arm to TrolleySectional Doors Only All ONE-PIECE Doors Adjustment Procedures for One-Piece DoorsHow and When to Adjust the Limits Adjustment Section Pages 28 Adjustment StepAdjust the UP and Down Limits How and When to Adjust the Forces Adjust the ForceTest the Down close force Test the UP open forceTest the Protector System Test the Safety Reverse SystemImportant safety check Limit and Force Adjustment Controls Maintenance ScheduleRemote control battery Care of Your OpenerOperation of the Multi-Function Door Control Operation of Your OpenerOutside Keylock or Keyless Entry Manual disconnect Position To open the door manuallyReceiver and Remote Control Programming Situation Probable Cause & Solution Having a Problem?Door control, a short under the staples, or a broken wire Are the wiring connections correct? Review ,Bulb if regular bulb burns out Is the Light feature on? Turn it offInstallation Parts Repair PartsRail Assembly Parts Complete with Opener Assembly PartsAccessories Available for your Opener Index Chamberlain Service Is on Call

8200 1/2 HP specifications

The Chamberlain 8200 is a robust and efficient garage door opener that combines power, reliability, and advanced technology to provide homeowners with a seamless experience. With its 1/2 HP motor, this opener is designed to handle sectional doors weighing up to 500 pounds, making it suitable for a variety of garage doors.

One of the standout features of the Chamberlain 8200 is its strong motor, which ensures smooth and quiet operation. This is particularly important for homeowners who have living spaces adjacent to the garage, as the reduced noise levels contribute to a more comfortable environment. The motor is also designed for durability and long-lasting performance, ensuring that it will consistently meet the needs of the user over time.

The Chamberlain 8200 comes equipped with the innovative MyQ technology, which enables users to control their garage door opener remotely via a smartphone app. This feature not only provides convenience but also enhances security, allowing homeowners to monitor and manage their garage door from anywhere. Whether you’re on vacation or simply at work, the ability to check the status of your garage door gives peace of mind.

Safety is another priority with the Chamberlain 8200, which includes features such as the patented Security+ 2.0 technology. This system ensures that your garage door opener transmits a new code every time the remote control is used, significantly reducing the risk of unauthorized access. Additionally, the opener is equipped with safety sensors that detect any obstructions in the door's path, preventing accidents or injuries.

Installation of the Chamberlain 8200 is straightforward, thanks to its detailed instructions and user-friendly design. The unit is compatible with a variety of garage door types and can easily integrate with existing door systems.

Overall, the Chamberlain 8200 1/2 HP garage door opener stands out as a powerful, technologically advanced solution for homeowners seeking convenience and security. Its blend of performance, innovative features, and user-friendly design makes it a top choice for modern garage door automation. Whether you are looking to upgrade your current system or installing a new opener, the Chamberlain 8200 promises reliability and peace of mind.
Top Page Image Contents