Chamberlain 8200 1/2 HP Install the Header Bracket, Fasten the Header Bracket to the Wall

Page 14

Installation Step 2

Install the Header Bracket

You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements.

Fasten the Header Bracket to the Wall

•Center the bracket on the vertical guideline with the bottom edge of the bracket on the horizontal line as shown (with the arrow pointing toward the ceiling).

•Mark either set of bracket holes (do not use the holes designated for ceiling mount). Drill 3/16" pilot holes and fasten the bracket securely to a structural support with the hardware provided.

Header

Wall

Header

Bracket

2x4

Structural

Support

Wall

Mounting Holes

Vertical

 

Center

CEILING MOUNT ONLY

ONLY

Line

Lag Screws

MOUNT

 

CEILING

 

 

5/16"x9x1-5/8"

UP

 

 

 

UP

Door

SpringThe nail hole is for positioning only. You must use lag screws to

mount the header bracket.

Optional

Wall Mounting

Holes

Highest

Point of Travel

(of Garage Door)

Garage

Door

Vertical

Center

Line

Hardware Shown Actual Size

Lag Screw

5/16"-9x1-5/8"

Fasten the Header Bracket to the Ceiling

•Extend the vertical guideline onto the ceiling as shown.

•Center the bracket on the vertical mark, no more than 6" from the wall. Make sure the arrow is pointing toward the wall. The bracket can be mounted flush against the ceiling when clearance is minimal.

•Mark holes designated for ceiling mount only. Drill 3/16" pilot holes and fasten bracket securely to a structural support with the hardware provided.

Ceiling Mounting Holes

CEILING MOUNT ONLY

UP

The nail hole is for positioning only. You must use lag screws to mount the header bracket.

 

Finished

 

Ceiling

 

Vertical

 

Center Line

 

Header

 

Bracket

 

UP

 

6" Maximum

Door

Lag Screws

Spring

5/16"x9x1-5/8"

Header

Wall

Vertical

Center Line

Garage

Door

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Garage Door Opener Model 8200 Series Assembly section pages 8 Start by reviewing these important safety alert symbolsContents Installation section pages 11Youll Need Tools Sectional Door Installation Closed PositionOne-Piece Door With Track ONE-PIECE Door InstallationOne-Piece Door without Track Carton Inventory SecurityAssembly Attach the Belt Pulley Bracket Assembly Section Pages 8Assembly Step Right WrongInstall the Trolley on the T-rail Faster the T-rail to the OpenerDo not use any tools Install the Belt & Set the Belt TensionCheck to make sure the belt is not twisted Attach the Belt Cap Retainer To attach the belt cap retainerSectional Door ONE-PIECE Door With Track Installation Section Pages 12 Installation StepDetermine Header Bracket Location Proceed to ,One-piece door without track Pivot hardware ExampleOne-piece door without track Jamb hardware =12Fasten the Header Bracket to the Ceiling Install the Header BracketFasten the Header Bracket to the Wall Attach the T-rail to the Header Bracket Raise the opener onto a stepladder Position the OpenerSectional Door & ONE-PIECE Door with Track Surface where Hang the OpenerGrease the top Underside of the rail Trolley slides with rail greaseTo opener terminal screws white to 2 white/red to Install the Multi-Function Door Control PanelOutside Keylock Accessory Connections See Safety Reversing Sensor Instructions beginning on Install the Lights and the Lenses32 explains how to use the door control Reverse the procedure to remove the lensesPermanent Wiring Connection Electrical RequirementsProtector System Facing the door from inside the garageInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Sectional Door Installation Procedure Fasten Door BracketHeader Wall Hole Alignment Alternative Connect Door Arm to TrolleySectional Doors Only Adjustment Procedures for One-Piece Doors All ONE-PIECE DoorsHow and When to Adjust the Limits Adjustment Section Pages 28 Adjustment StepAdjust the UP and Down Limits Test the Down close force Adjust the ForceHow and When to Adjust the Forces Test the UP open forceTest the Protector System Test the Safety Reverse SystemImportant safety check Remote control battery Maintenance ScheduleLimit and Force Adjustment Controls Care of Your OpenerOutside Keylock or Keyless Entry Operation of Your OpenerOperation of the Multi-Function Door Control Manual disconnect Position To open the door manuallyReceiver and Remote Control Programming Door control, a short under the staples, or a broken wire Having a Problem?Situation Probable Cause & Solution Are the wiring connections correct? Review ,Is the Light feature on? Turn it off Bulb if regular bulb burns outInstallation Parts Repair PartsRail Assembly Parts Opener Assembly Parts Complete withAccessories Available for your Opener Index Chamberlain Service Is on Call

8200 1/2 HP specifications

The Chamberlain 8200 is a robust and efficient garage door opener that combines power, reliability, and advanced technology to provide homeowners with a seamless experience. With its 1/2 HP motor, this opener is designed to handle sectional doors weighing up to 500 pounds, making it suitable for a variety of garage doors.

One of the standout features of the Chamberlain 8200 is its strong motor, which ensures smooth and quiet operation. This is particularly important for homeowners who have living spaces adjacent to the garage, as the reduced noise levels contribute to a more comfortable environment. The motor is also designed for durability and long-lasting performance, ensuring that it will consistently meet the needs of the user over time.

The Chamberlain 8200 comes equipped with the innovative MyQ technology, which enables users to control their garage door opener remotely via a smartphone app. This feature not only provides convenience but also enhances security, allowing homeowners to monitor and manage their garage door from anywhere. Whether you’re on vacation or simply at work, the ability to check the status of your garage door gives peace of mind.

Safety is another priority with the Chamberlain 8200, which includes features such as the patented Security+ 2.0 technology. This system ensures that your garage door opener transmits a new code every time the remote control is used, significantly reducing the risk of unauthorized access. Additionally, the opener is equipped with safety sensors that detect any obstructions in the door's path, preventing accidents or injuries.

Installation of the Chamberlain 8200 is straightforward, thanks to its detailed instructions and user-friendly design. The unit is compatible with a variety of garage door types and can easily integrate with existing door systems.

Overall, the Chamberlain 8200 1/2 HP garage door opener stands out as a powerful, technologically advanced solution for homeowners seeking convenience and security. Its blend of performance, innovative features, and user-friendly design makes it a top choice for modern garage door automation. Whether you are looking to upgrade your current system or installing a new opener, the Chamberlain 8200 promises reliability and peace of mind.
Top Page Image Contents