Chamberlain 8200 1/2 HP owner manual Fasten Door Bracket, Sectional Door Installation Procedure

Page 24

Installation Step 11

Fasten Door Bracket

Follow instructions which apply to your door type as illustrated below or on page 25.

CAUTION

To prevent damage to steel, aluminum, fiberglass or glass panel doors, always reinforce the inside of the door both vertically and horizontally with an angle iron.

A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should cover the height of the top panel.

The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of angle iron are used to create a "U"-shaped support. The best solution is to check with your garage door manufacturer for an opener installation door reinforcement kit.

SECTIONAL Door Installation Procedure

Header

Bracket

Door

Bracket

Location

Vertical

Guideline

•Center the door bracket on the previously marked vertical guideline used for the header bracket installation. Note correct UP placement, as stamped inside the bracket.

•Position the bracket on the face of the door within the following limits:

A)The top edge of the bracket 2"-4" below the top edge of the door.

B)The top edge of the bracket directly below any structural support across the top of the door.

•Mark and drill 5/16" left and right fastening holes. Secure the bracket as shown in Figure 1 if there is vertical reinforcement.

If your installation doesn't require vertical reinforce- ment but does need top and bottom fastening holes for the door bracket, fasten as shown in Figure 2.

Horizontal and vertical reinforcement

 

is needed for lightweight garage doors

 

(fiberglass, aluminum, steel,

Figure 1

doors with glass panel, etc).

Vertical

Reinforcement

 

 

Vertical

 

 

Guideline

Carriage Bolt

 

UP

 

 

5/16"-18x2-1/2"

 

 

Door

 

 

Bracket

Lock

 

 

 

 

Washer

 

5/16"

Nut

 

 

 

 

5/16"-18

 

 

Figure 2

Inside Edge

of Door or

Reinforcement Board

UP

Door Bracket

Hardware Shown Actual Size

Nut 5/16"-18

Lock Washer 5/16"

 

Carriage Bolt

 

5/16"-18x2-1/2"

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Garage Door Opener Model 8200 Series Start by reviewing these important safety alert symbols ContentsAssembly section pages 8 Installation section pages 11Youll Need Tools Sectional Door Installation Closed PositionONE-PIECE Door Installation One-Piece Door without TrackOne-Piece Door With Track Carton Inventory SecurityAssembly Assembly Section Pages 8 Assembly StepAttach the Belt Pulley Bracket Right WrongInstall the Trolley on the T-rail Faster the T-rail to the OpenerInstall the Belt & Set the Belt Tension Check to make sure the belt is not twistedDo not use any tools Attach the Belt Cap Retainer To attach the belt cap retainerInstallation Section Pages 12 Installation Step Determine Header Bracket LocationSectional Door ONE-PIECE Door With Track Proceed to ,Example One-piece door without track Jamb hardwareOne-piece door without track Pivot hardware =12Install the Header Bracket Fasten the Header Bracket to the WallFasten the Header Bracket to the Ceiling Attach the T-rail to the Header Bracket Position the Opener Sectional Door & ONE-PIECE Door with TrackRaise the opener onto a stepladder Hang the Opener Grease the top Underside of the railSurface where Trolley slides with rail greaseInstall the Multi-Function Door Control Panel Outside Keylock Accessory ConnectionsTo opener terminal screws white to 2 white/red to Install the Lights and the Lenses 32 explains how to use the door controlSee Safety Reversing Sensor Instructions beginning on Reverse the procedure to remove the lensesPermanent Wiring Connection Electrical RequirementsProtector System Facing the door from inside the garageInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Sectional Door Installation Procedure Fasten Door BracketHeader Wall Connect Door Arm to Trolley Sectional Doors OnlyHole Alignment Alternative Adjustment Procedures for One-Piece Doors All ONE-PIECE DoorsAdjustment Section Pages 28 Adjustment Step Adjust the UP and Down LimitsHow and When to Adjust the Limits Adjust the Force How and When to Adjust the ForcesTest the Down close force Test the UP open forceTest the Safety Reverse System Important safety checkTest the Protector System Maintenance Schedule Limit and Force Adjustment ControlsRemote control battery Care of Your OpenerOperation of Your Opener Operation of the Multi-Function Door ControlOutside Keylock or Keyless Entry Manual disconnect Position To open the door manuallyReceiver and Remote Control Programming Having a Problem? Situation Probable Cause & SolutionDoor control, a short under the staples, or a broken wire Are the wiring connections correct? Review ,Is the Light feature on? Turn it off Bulb if regular bulb burns outRepair Parts Rail Assembly PartsInstallation Parts Opener Assembly Parts Complete withAccessories Available for your Opener Index Chamberlain Service Is on Call

8200 1/2 HP specifications

The Chamberlain 8200 is a robust and efficient garage door opener that combines power, reliability, and advanced technology to provide homeowners with a seamless experience. With its 1/2 HP motor, this opener is designed to handle sectional doors weighing up to 500 pounds, making it suitable for a variety of garage doors.

One of the standout features of the Chamberlain 8200 is its strong motor, which ensures smooth and quiet operation. This is particularly important for homeowners who have living spaces adjacent to the garage, as the reduced noise levels contribute to a more comfortable environment. The motor is also designed for durability and long-lasting performance, ensuring that it will consistently meet the needs of the user over time.

The Chamberlain 8200 comes equipped with the innovative MyQ technology, which enables users to control their garage door opener remotely via a smartphone app. This feature not only provides convenience but also enhances security, allowing homeowners to monitor and manage their garage door from anywhere. Whether you’re on vacation or simply at work, the ability to check the status of your garage door gives peace of mind.

Safety is another priority with the Chamberlain 8200, which includes features such as the patented Security+ 2.0 technology. This system ensures that your garage door opener transmits a new code every time the remote control is used, significantly reducing the risk of unauthorized access. Additionally, the opener is equipped with safety sensors that detect any obstructions in the door's path, preventing accidents or injuries.

Installation of the Chamberlain 8200 is straightforward, thanks to its detailed instructions and user-friendly design. The unit is compatible with a variety of garage door types and can easily integrate with existing door systems.

Overall, the Chamberlain 8200 1/2 HP garage door opener stands out as a powerful, technologically advanced solution for homeowners seeking convenience and security. Its blend of performance, innovative features, and user-friendly design makes it a top choice for modern garage door automation. Whether you are looking to upgrade your current system or installing a new opener, the Chamberlain 8200 promises reliability and peace of mind.
Top Page Image Contents