Chamberlain 8200 1/2 HP All ONE-PIECE Doors, Adjustment Procedures for One-Piece Doors

Page 27

All ONE-PIECE Doors

Assemble the Door Arm:

•Fasten the straight and curved door arm sections together to the longest possible length (with a

2 or 3 hole overlap).

•With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin.

•Secure with a ring fastener.

Door

Ring

 

 

Bracket

Fastener

 

 

 

 

Lock

Nuts

 

 

5/16"-18

 

 

Washers

 

 

 

 

 

5/16"

 

Clevis Pin

Straight

 

 

5/16"x1-1/4"

Arm

 

 

 

Screws

 

Curved

 

5/16"-18x7/8

 

 

 

 

Door Arm

On one-piece doors, before connecting the door arm to the trolley the travel limits must be adjusted. Limit adjustment screws are located on the left side panel as shown on page 28. Follow adjustment procedures below.

Fully Closed

Trolley

Fully Open

Trolley

Door Arm

Door Arm

 

Connector Hole

 

Door Arm

 

Connector Hole

Closed

 

 

 

Door

Open Door

Door with

Door Arm

 

 

Backward Slant

 

Adjustment Procedures for One-Piece Doors

Open Door Adjustment:

Decrease UP limit

•Turn the UP limit adjustment screw counter- clockwise 5-1/2 turns.

•Press the Door Control push bar. The trolley will travel to the fully open position.

•Manually raise the door to the open position (parallel to the floor), and lift the door arm to the trolley. The arm should touch the trolley just in back of the door arm connector hole. Refer to the fully open trolley/door arm positions in the illustration. If the arm does not extend far enough, adjust the limit further. One full turn equals 2" of trolley travel.

Closed Door Adjustment:

Decrease DOWN limit

•Turn the DOWN limit adjustment screw clockwise 5 complete turns.

•Press the Door Control push bar. The trolley will travel to the fully closed position.

•Manually close the door and lift the door arm to the trolley. The arm should touch the trolley just ahead of the door arm connector hole. Refer to the fully closed trolley/door arm positions in the illustration. If the arm is behind the connector hole, adjust the limit further. One full turn equals 2" of trolley travel.

Connect the door arm to the trolley:

•Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may be necessary to lift the door slightly to make the connection.

•Secure with a ring fastener.

•Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position as shown in the illustration, decrease the UP limit until the door is parallel to the floor.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Garage Door Opener Model 8200 Series Installation section pages 11 Start by reviewing these important safety alert symbolsContents Assembly section pages 8Youll Need Tools Closed Position Sectional Door InstallationONE-PIECE Door Installation One-Piece Door without TrackOne-Piece Door With Track Security Carton InventoryAssembly Right Wrong Assembly Section Pages 8Assembly Step Attach the Belt Pulley BracketFaster the T-rail to the Opener Install the Trolley on the T-railInstall the Belt & Set the Belt Tension Check to make sure the belt is not twistedDo not use any tools To attach the belt cap retainer Attach the Belt Cap RetainerProceed to , Installation Section Pages 12 Installation StepDetermine Header Bracket Location Sectional Door ONE-PIECE Door With Track=12 ExampleOne-piece door without track Jamb hardware One-piece door without track Pivot hardwareInstall the Header Bracket Fasten the Header Bracket to the WallFasten the Header Bracket to the Ceiling Attach the T-rail to the Header Bracket Position the Opener Sectional Door & ONE-PIECE Door with TrackRaise the opener onto a stepladder Trolley slides with rail grease Hang the OpenerGrease the top Underside of the rail Surface whereInstall the Multi-Function Door Control Panel Outside Keylock Accessory ConnectionsTo opener terminal screws white to 2 white/red to Reverse the procedure to remove the lenses Install the Lights and the Lenses32 explains how to use the door control See Safety Reversing Sensor Instructions beginning onElectrical Requirements Permanent Wiring ConnectionFacing the door from inside the garage Protector SystemInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Fasten Door Bracket Sectional Door Installation ProcedureHeader Wall Connect Door Arm to Trolley Sectional Doors OnlyHole Alignment Alternative All ONE-PIECE Doors Adjustment Procedures for One-Piece DoorsAdjustment Section Pages 28 Adjustment Step Adjust the UP and Down LimitsHow and When to Adjust the Limits Test the UP open force Adjust the ForceHow and When to Adjust the Forces Test the Down close forceTest the Safety Reverse System Important safety checkTest the Protector System Care of Your Opener Maintenance ScheduleLimit and Force Adjustment Controls Remote control batteryManual disconnect Position To open the door manually Operation of Your OpenerOperation of the Multi-Function Door Control Outside Keylock or Keyless EntryReceiver and Remote Control Programming Are the wiring connections correct? Review , Having a Problem?Situation Probable Cause & Solution Door control, a short under the staples, or a broken wireBulb if regular bulb burns out Is the Light feature on? Turn it offRepair Parts Rail Assembly PartsInstallation Parts Complete with Opener Assembly PartsAccessories Available for your Opener Index Chamberlain Service Is on Call

8200 1/2 HP specifications

The Chamberlain 8200 is a robust and efficient garage door opener that combines power, reliability, and advanced technology to provide homeowners with a seamless experience. With its 1/2 HP motor, this opener is designed to handle sectional doors weighing up to 500 pounds, making it suitable for a variety of garage doors.

One of the standout features of the Chamberlain 8200 is its strong motor, which ensures smooth and quiet operation. This is particularly important for homeowners who have living spaces adjacent to the garage, as the reduced noise levels contribute to a more comfortable environment. The motor is also designed for durability and long-lasting performance, ensuring that it will consistently meet the needs of the user over time.

The Chamberlain 8200 comes equipped with the innovative MyQ technology, which enables users to control their garage door opener remotely via a smartphone app. This feature not only provides convenience but also enhances security, allowing homeowners to monitor and manage their garage door from anywhere. Whether you’re on vacation or simply at work, the ability to check the status of your garage door gives peace of mind.

Safety is another priority with the Chamberlain 8200, which includes features such as the patented Security+ 2.0 technology. This system ensures that your garage door opener transmits a new code every time the remote control is used, significantly reducing the risk of unauthorized access. Additionally, the opener is equipped with safety sensors that detect any obstructions in the door's path, preventing accidents or injuries.

Installation of the Chamberlain 8200 is straightforward, thanks to its detailed instructions and user-friendly design. The unit is compatible with a variety of garage door types and can easily integrate with existing door systems.

Overall, the Chamberlain 8200 1/2 HP garage door opener stands out as a powerful, technologically advanced solution for homeowners seeking convenience and security. Its blend of performance, innovative features, and user-friendly design makes it a top choice for modern garage door automation. Whether you are looking to upgrade your current system or installing a new opener, the Chamberlain 8200 promises reliability and peace of mind.
Top Page Image Contents