Chamberlain 8200 1/2 HP owner manual Test the Protector System, Test the Safety Reverse System

Page 30

Adjustment Step 3

Test the Protector System®

•Press the remote control push button to open the door.

•Place the opener carton in the path of the door.

•Press the remote control push button to close the door. The door will not move more than an inch, and the opener lights will flash.

Professional service is required if the opener closes the door when the safety reversing sensor is obstructed.

The garage door opener will not close from a remote if the indicator light in either sensor is off (alerting you to the fact that the sensor is misaligned or obstructed).

The garage door can be closed by pressing and holding the Door Control push bar until down travel is completed.

WARNING

Without a properly working safety reversing sensor, persons (particularly children) could be seriously injured or killed if trapped by a closing garage door. Repeat this test once a month.

Safety Reversing Sensor

Safety Reversing Sensor

Adjustment Step 4

Test the Safety Reverse System

Test:

•With the door fully open, place a one-inch board (or a 2x4 laid flat) on the floor, centered under the garage door.

•Operate the door in the down direction. The door must reverse on striking the obstruction.

Adjustment:

If the door stops on the obstruction, it is not traveling far enough in the down direction.

•Increase the DOWN limit by turning the DOWN limit adjustment screw counterclockwise 1/4 turn.

•Repeat the test.

On a sectional door, make sure limit adjustments do not force the door arm beyond a straight up and down position. See the illustration on page 26.

•When the door reverses on the one-inch board (or a 2x4 laid flat), remove the obstruction and run the opener through 3 or 4 complete travel cycles to test adjustment.

If the door will not reverse after repeated adjustment attempts, call for professional garage door service.

Important safety check:

Repeat Adjustment Steps 1, 2 and 4 after:

•Each adjustment of door arm length, force controls or limit controls.

•Any repair to or adjustment of the garage door (including springs and hardware).

•Any repair to or buckling of the garage floor.

•Any repair to or adjustment of the opener.

WARNING

Failure to test and adjust the safety reverse system may result in serious injury or death to persons trapped by a closing garage door. Repeat this test once a month and adjust as needed.

GARAGE DOOR

One-Inch Board

(or a 2x4 Laid Flat)

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Garage Door Opener Model 8200 Series Assembly section pages 8 Start by reviewing these important safety alert symbolsContents Installation section pages 11Youll Need Tools Sectional Door Installation Closed PositionONE-PIECE Door Installation One-Piece Door without TrackOne-Piece Door With Track Carton Inventory SecurityAssembly Attach the Belt Pulley Bracket Assembly Section Pages 8Assembly Step Right WrongInstall the Trolley on the T-rail Faster the T-rail to the OpenerInstall the Belt & Set the Belt Tension Check to make sure the belt is not twistedDo not use any tools Attach the Belt Cap Retainer To attach the belt cap retainerSectional Door ONE-PIECE Door With Track Installation Section Pages 12 Installation StepDetermine Header Bracket Location Proceed to ,One-piece door without track Pivot hardware ExampleOne-piece door without track Jamb hardware =12Install the Header Bracket Fasten the Header Bracket to the WallFasten the Header Bracket to the Ceiling Attach the T-rail to the Header Bracket Position the Opener Sectional Door & ONE-PIECE Door with TrackRaise the opener onto a stepladder Surface where Hang the OpenerGrease the top Underside of the rail Trolley slides with rail greaseInstall the Multi-Function Door Control Panel Outside Keylock Accessory ConnectionsTo opener terminal screws white to 2 white/red to See Safety Reversing Sensor Instructions beginning on Install the Lights and the Lenses32 explains how to use the door control Reverse the procedure to remove the lensesPermanent Wiring Connection Electrical RequirementsProtector System Facing the door from inside the garageInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Sectional Door Installation Procedure Fasten Door BracketHeader Wall Connect Door Arm to Trolley Sectional Doors OnlyHole Alignment Alternative Adjustment Procedures for One-Piece Doors All ONE-PIECE DoorsAdjustment Section Pages 28 Adjustment Step Adjust the UP and Down LimitsHow and When to Adjust the Limits Test the Down close force Adjust the ForceHow and When to Adjust the Forces Test the UP open forceTest the Safety Reverse System Important safety checkTest the Protector System Remote control battery Maintenance ScheduleLimit and Force Adjustment Controls Care of Your OpenerOutside Keylock or Keyless Entry Operation of Your OpenerOperation of the Multi-Function Door Control Manual disconnect Position To open the door manuallyReceiver and Remote Control Programming Door control, a short under the staples, or a broken wire Having a Problem?Situation Probable Cause & Solution Are the wiring connections correct? Review ,Is the Light feature on? Turn it off Bulb if regular bulb burns outRepair Parts Rail Assembly PartsInstallation Parts Opener Assembly Parts Complete withAccessories Available for your Opener Index Chamberlain Service Is on Call

8200 1/2 HP specifications

The Chamberlain 8200 is a robust and efficient garage door opener that combines power, reliability, and advanced technology to provide homeowners with a seamless experience. With its 1/2 HP motor, this opener is designed to handle sectional doors weighing up to 500 pounds, making it suitable for a variety of garage doors.

One of the standout features of the Chamberlain 8200 is its strong motor, which ensures smooth and quiet operation. This is particularly important for homeowners who have living spaces adjacent to the garage, as the reduced noise levels contribute to a more comfortable environment. The motor is also designed for durability and long-lasting performance, ensuring that it will consistently meet the needs of the user over time.

The Chamberlain 8200 comes equipped with the innovative MyQ technology, which enables users to control their garage door opener remotely via a smartphone app. This feature not only provides convenience but also enhances security, allowing homeowners to monitor and manage their garage door from anywhere. Whether you’re on vacation or simply at work, the ability to check the status of your garage door gives peace of mind.

Safety is another priority with the Chamberlain 8200, which includes features such as the patented Security+ 2.0 technology. This system ensures that your garage door opener transmits a new code every time the remote control is used, significantly reducing the risk of unauthorized access. Additionally, the opener is equipped with safety sensors that detect any obstructions in the door's path, preventing accidents or injuries.

Installation of the Chamberlain 8200 is straightforward, thanks to its detailed instructions and user-friendly design. The unit is compatible with a variety of garage door types and can easily integrate with existing door systems.

Overall, the Chamberlain 8200 1/2 HP garage door opener stands out as a powerful, technologically advanced solution for homeowners seeking convenience and security. Its blend of performance, innovative features, and user-friendly design makes it a top choice for modern garage door automation. Whether you are looking to upgrade your current system or installing a new opener, the Chamberlain 8200 promises reliability and peace of mind.
Top Page Image Contents