Chamberlain 8200 1/2 HP owner manual Header Wall

Page 25

All ONE-PIECE Door Installation Procedure

Please read and comply with the warnings and reinforcement instructions on page 24. They apply to one-piece doors also.

Header Wall

— Finished Ceiling —

 

2x4 Support

Header

 

Bracket

Optional

Door

Bracket

Placement

 

of Door

 

Bracket

 

Vertical

 

Centerline of

 

Garage Door

Horizontal and vertical

reinforcement is needed for

lightweight garage doors (fiberglass, aluminum, steel, door with glass panel, etc.). (Not Provided)

Nut 5/16"-18

Door

Bracket

For a door with no exposed framing or for the optional installation, use 5/16"x1-1/2" lag screws (not provided) to fasten door bracket.

Lock Washer 5/16"

Top of Door

(Inside Garage)

Top Edge

of Door

Optional

Placement

Carriage Bolt

5/16"-18x2-1/2"

•Center the bracket on the top of the door, in line with the header bracket as shown. Mark holes.

•Drill 5/16" pilot holes and fasten the door bracket with hardware provided.

If the door has no exposed framing, drill 3/16" pilot holes and fasten the bracket with 5/16"x1-1/2" lag screws (not provided) to the top of the door.

The door bracket may be installed on the top edge of the door if required for your installation. (Refer to the dotted line optional placement drawing.) Drill 3/16" pilot holes and substitute 5/16"x1-1/2" lag screws (not provided) to fasten the bracket to the door.

Hardware Shown Actual Size

Nut 5/16"-18

Lock Washer 5/16"

 

Carriage Bolt

 

5/16"-18x2-1/2"

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Garage Door Opener Model 8200 Series Contents Start by reviewing these important safety alert symbolsAssembly section pages 8 Installation section pages 11Youll Need Tools Closed Position Sectional Door InstallationOne-Piece Door without Track ONE-PIECE Door InstallationOne-Piece Door With Track Security Carton InventoryAssembly Assembly Step Assembly Section Pages 8Attach the Belt Pulley Bracket Right WrongFaster the T-rail to the Opener Install the Trolley on the T-railCheck to make sure the belt is not twisted Install the Belt & Set the Belt TensionDo not use any tools To attach the belt cap retainer Attach the Belt Cap RetainerDetermine Header Bracket Location Installation Section Pages 12 Installation StepSectional Door ONE-PIECE Door With Track Proceed to ,One-piece door without track Jamb hardware ExampleOne-piece door without track Pivot hardware =12Fasten the Header Bracket to the Wall Install the Header BracketFasten the Header Bracket to the Ceiling Attach the T-rail to the Header Bracket Sectional Door & ONE-PIECE Door with Track Position the OpenerRaise the opener onto a stepladder Grease the top Underside of the rail Hang the OpenerSurface where Trolley slides with rail greaseOutside Keylock Accessory Connections Install the Multi-Function Door Control PanelTo opener terminal screws white to 2 white/red to 32 explains how to use the door control Install the Lights and the LensesSee Safety Reversing Sensor Instructions beginning on Reverse the procedure to remove the lensesElectrical Requirements Permanent Wiring ConnectionFacing the door from inside the garage Protector SystemInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Fasten Door Bracket Sectional Door Installation ProcedureHeader Wall Sectional Doors Only Connect Door Arm to TrolleyHole Alignment Alternative All ONE-PIECE Doors Adjustment Procedures for One-Piece DoorsAdjust the UP and Down Limits Adjustment Section Pages 28 Adjustment StepHow and When to Adjust the Limits How and When to Adjust the Forces Adjust the ForceTest the Down close force Test the UP open forceImportant safety check Test the Safety Reverse SystemTest the Protector System Limit and Force Adjustment Controls Maintenance ScheduleRemote control battery Care of Your OpenerOperation of the Multi-Function Door Control Operation of Your OpenerOutside Keylock or Keyless Entry Manual disconnect Position To open the door manuallyReceiver and Remote Control Programming Situation Probable Cause & Solution Having a Problem?Door control, a short under the staples, or a broken wire Are the wiring connections correct? Review ,Bulb if regular bulb burns out Is the Light feature on? Turn it offRail Assembly Parts Repair PartsInstallation Parts Complete with Opener Assembly PartsAccessories Available for your Opener Index Chamberlain Service Is on Call

8200 1/2 HP specifications

The Chamberlain 8200 is a robust and efficient garage door opener that combines power, reliability, and advanced technology to provide homeowners with a seamless experience. With its 1/2 HP motor, this opener is designed to handle sectional doors weighing up to 500 pounds, making it suitable for a variety of garage doors.

One of the standout features of the Chamberlain 8200 is its strong motor, which ensures smooth and quiet operation. This is particularly important for homeowners who have living spaces adjacent to the garage, as the reduced noise levels contribute to a more comfortable environment. The motor is also designed for durability and long-lasting performance, ensuring that it will consistently meet the needs of the user over time.

The Chamberlain 8200 comes equipped with the innovative MyQ technology, which enables users to control their garage door opener remotely via a smartphone app. This feature not only provides convenience but also enhances security, allowing homeowners to monitor and manage their garage door from anywhere. Whether you’re on vacation or simply at work, the ability to check the status of your garage door gives peace of mind.

Safety is another priority with the Chamberlain 8200, which includes features such as the patented Security+ 2.0 technology. This system ensures that your garage door opener transmits a new code every time the remote control is used, significantly reducing the risk of unauthorized access. Additionally, the opener is equipped with safety sensors that detect any obstructions in the door's path, preventing accidents or injuries.

Installation of the Chamberlain 8200 is straightforward, thanks to its detailed instructions and user-friendly design. The unit is compatible with a variety of garage door types and can easily integrate with existing door systems.

Overall, the Chamberlain 8200 1/2 HP garage door opener stands out as a powerful, technologically advanced solution for homeowners seeking convenience and security. Its blend of performance, innovative features, and user-friendly design makes it a top choice for modern garage door automation. Whether you are looking to upgrade your current system or installing a new opener, the Chamberlain 8200 promises reliability and peace of mind.
Top Page Image Contents