Chamberlain 8200 1/2 HP Install the Trolley on the T-rail, Faster the T-rail to the Opener

Page 9

Assembly Step 2

Install the Trolley on the T-rail

Trolley

•As a temporary stop, insert a screwdriver into the hole in the front end of the T-rail.

•Slide the trolley assembly along the rail to the screwdriver stop.

If trolley hits against any nuts on the T-rail, the bolts and nuts were attached from the wrong side and must be repositioned. Review Step 1.

Temporary Stop

Screwdriver

Hex Screw

5/16"-18x7/8"

Trolley

Stop Hole

Lock Washer 5/16"

Nut 5/16"-18

•Insert a 5/16"-18x7/8" hex screw into the trolley stop hole in the T-rail as shown. Tighten securely with a 5/16" lock washer and nut. This screw limits trolley travel in the DOWN direction.

Assembly Step 3

Faster the T-rail to the Opener

•Place the opener on packing material to protect the cover. For convenience, put a support under the belt pulley bracket.

•Remove the (2) 5/16"-18x1/2" washered screws mounted in the top of the opener.

•Align the holes in the back section of the T-rail with the holes in the opener.

•Fasten the rail with the (2) washered screws previously removed. Tighten securely.

Remember to use only these screws! Any other screws will cause serious damage to the opener.

•Insert a 5/16"-18x7/8" hex screw into the cover protection bolt hole in the T-rail as shown. Tighten securely with a 5/16" lock washer and nut.

NOTE: This screw prevents trolley over-travel. Keep a 2" minimum between the trolley and this screw when adjusting travel limits (see page 28).

Hardware Shown Actual Size

CAUTION

To fasten rail, use only those screws mounted in the top of the opener. Any other screws will cause serious damage to the opener.

Washered Screw

5/16"-18x1/2"

USE ONLY THIS

Hex Screw

TYPE AND SIZE

5/16"-18x7/8"

SCREW

 

Cover Protection

BoltHole

T-Rail

(Back Section)

Lock Washer

5/16"

Nut

5/16"-18

Hex Screw

Nut

Lock Washer

5/16"-18x7/8"

5/16"-18

5/16"

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Garage Door Opener Model 8200 Series Contents Start by reviewing these important safety alert symbolsAssembly section pages 8 Installation section pages 11Youll Need Tools Closed Position Sectional Door InstallationONE-PIECE Door Installation One-Piece Door without TrackOne-Piece Door With Track Security Carton InventoryAssembly Assembly Step Assembly Section Pages 8Attach the Belt Pulley Bracket Right WrongFaster the T-rail to the Opener Install the Trolley on the T-railInstall the Belt & Set the Belt Tension Check to make sure the belt is not twistedDo not use any tools To attach the belt cap retainer Attach the Belt Cap RetainerDetermine Header Bracket Location Installation Section Pages 12 Installation StepSectional Door ONE-PIECE Door With Track Proceed to ,One-piece door without track Jamb hardware ExampleOne-piece door without track Pivot hardware =12Install the Header Bracket Fasten the Header Bracket to the WallFasten the Header Bracket to the Ceiling Attach the T-rail to the Header Bracket Position the Opener Sectional Door & ONE-PIECE Door with TrackRaise the opener onto a stepladder Grease the top Underside of the rail Hang the OpenerSurface where Trolley slides with rail greaseInstall the Multi-Function Door Control Panel Outside Keylock Accessory ConnectionsTo opener terminal screws white to 2 white/red to 32 explains how to use the door control Install the Lights and the LensesSee Safety Reversing Sensor Instructions beginning on Reverse the procedure to remove the lensesElectrical Requirements Permanent Wiring ConnectionFacing the door from inside the garage Protector SystemInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Fasten Door Bracket Sectional Door Installation ProcedureHeader Wall Connect Door Arm to Trolley Sectional Doors OnlyHole Alignment Alternative All ONE-PIECE Doors Adjustment Procedures for One-Piece DoorsAdjustment Section Pages 28 Adjustment Step Adjust the UP and Down LimitsHow and When to Adjust the Limits How and When to Adjust the Forces Adjust the ForceTest the Down close force Test the UP open forceTest the Safety Reverse System Important safety checkTest the Protector System Limit and Force Adjustment Controls Maintenance ScheduleRemote control battery Care of Your OpenerOperation of the Multi-Function Door Control Operation of Your OpenerOutside Keylock or Keyless Entry Manual disconnect Position To open the door manuallyReceiver and Remote Control Programming Situation Probable Cause & Solution Having a Problem?Door control, a short under the staples, or a broken wire Are the wiring connections correct? Review ,Bulb if regular bulb burns out Is the Light feature on? Turn it offRepair Parts Rail Assembly PartsInstallation Parts Complete with Opener Assembly PartsAccessories Available for your Opener Index Chamberlain Service Is on Call

8200 1/2 HP specifications

The Chamberlain 8200 is a robust and efficient garage door opener that combines power, reliability, and advanced technology to provide homeowners with a seamless experience. With its 1/2 HP motor, this opener is designed to handle sectional doors weighing up to 500 pounds, making it suitable for a variety of garage doors.

One of the standout features of the Chamberlain 8200 is its strong motor, which ensures smooth and quiet operation. This is particularly important for homeowners who have living spaces adjacent to the garage, as the reduced noise levels contribute to a more comfortable environment. The motor is also designed for durability and long-lasting performance, ensuring that it will consistently meet the needs of the user over time.

The Chamberlain 8200 comes equipped with the innovative MyQ technology, which enables users to control their garage door opener remotely via a smartphone app. This feature not only provides convenience but also enhances security, allowing homeowners to monitor and manage their garage door from anywhere. Whether you’re on vacation or simply at work, the ability to check the status of your garage door gives peace of mind.

Safety is another priority with the Chamberlain 8200, which includes features such as the patented Security+ 2.0 technology. This system ensures that your garage door opener transmits a new code every time the remote control is used, significantly reducing the risk of unauthorized access. Additionally, the opener is equipped with safety sensors that detect any obstructions in the door's path, preventing accidents or injuries.

Installation of the Chamberlain 8200 is straightforward, thanks to its detailed instructions and user-friendly design. The unit is compatible with a variety of garage door types and can easily integrate with existing door systems.

Overall, the Chamberlain 8200 1/2 HP garage door opener stands out as a powerful, technologically advanced solution for homeowners seeking convenience and security. Its blend of performance, innovative features, and user-friendly design makes it a top choice for modern garage door automation. Whether you are looking to upgrade your current system or installing a new opener, the Chamberlain 8200 promises reliability and peace of mind.
Top Page Image Contents