Chamberlain 8200 1/2 HP Install the Lights and the Lenses, explains how to use the door control

Page 19

•Attach the User Safety Instruction label to the wall near the door control, and the Maintenance Instruction label in a prominent location on the inside of the garage door.

Page 32 explains how to use the door control.

Do NOT connect the power and operate the opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.

See Safety Reversing Sensor Instructions beginning on page 21.

Installation Step 7

Install the Lights and the Lenses

Lens

•Install a 75 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF.

•If the bulbs burn out prematurely due to vibration, replace them with "Garage Door Opener" bulbs.

•Slide lenses into guides as shown. Snap bottom tabs into lens slots.

•For convenience, the lenses may be installed after Adjustment Step 4 on page 30.

•Reverse the procedure to remove the lenses.

Lens Tab

75 Watt Max.

Light Bulb

Guide

75 Watt Max.

Light Bulb

Lens Slot

Lens Tab

Installation Step 8

Attach the Manual Release

Rope and Handle

 

 

Overhand

 

 

Knot

Trolley

 

Trolley

 

Rope

Release Arm

 

 

 

 

Manual

 

Overhand

Release Handle

 

 

 

Knot

 

WARNING

Do not use the red handle to pull the door open or closed. The rope knot could become untied and you could fall. Use the manual release only to disengage the trolley and, if possible, only when the door is closed.

Garage doors are heavy. If the door is open when the handle is pulled, the door could close inadvertently if it is not properly balanced. Serious injury may result to persons under the door. Make sure the doorway is clear of persons and obstructions before pulling handle when door is open.

•Thread one end of the rope through the hole in the top of the red handle so "NOTICE" reads right side up as shown. Secure with an overhand knot at least 1" from the end of the rope to prevent slipping.

•Thread the other end of the rope through the hole in the release arm of the outer trolley.

•Adjust rope length so the handle is 6 feet above the floor. Secure with an overhand knot .

If it is necessary to cut the rope, heat seal the cut end with a match or lighter to prevent unraveling.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Garage Door Opener Model 8200 Series Installation section pages 11 Start by reviewing these important safety alert symbolsContents Assembly section pages 8Youll Need Tools Closed Position Sectional Door InstallationOne-Piece Door without Track ONE-PIECE Door InstallationOne-Piece Door With Track Security Carton InventoryAssembly Right Wrong Assembly Section Pages 8Assembly Step Attach the Belt Pulley BracketFaster the T-rail to the Opener Install the Trolley on the T-railCheck to make sure the belt is not twisted Install the Belt & Set the Belt TensionDo not use any tools To attach the belt cap retainer Attach the Belt Cap RetainerProceed to , Installation Section Pages 12 Installation StepDetermine Header Bracket Location Sectional Door ONE-PIECE Door With Track=12 ExampleOne-piece door without track Jamb hardware One-piece door without track Pivot hardwareFasten the Header Bracket to the Wall Install the Header BracketFasten the Header Bracket to the Ceiling Attach the T-rail to the Header Bracket Sectional Door & ONE-PIECE Door with Track Position the OpenerRaise the opener onto a stepladder Trolley slides with rail grease Hang the OpenerGrease the top Underside of the rail Surface whereOutside Keylock Accessory Connections Install the Multi-Function Door Control PanelTo opener terminal screws white to 2 white/red to Reverse the procedure to remove the lenses Install the Lights and the Lenses32 explains how to use the door control See Safety Reversing Sensor Instructions beginning onElectrical Requirements Permanent Wiring ConnectionFacing the door from inside the garage Protector SystemInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Fasten Door Bracket Sectional Door Installation ProcedureHeader Wall Sectional Doors Only Connect Door Arm to TrolleyHole Alignment Alternative All ONE-PIECE Doors Adjustment Procedures for One-Piece DoorsAdjust the UP and Down Limits Adjustment Section Pages 28 Adjustment StepHow and When to Adjust the Limits Test the UP open force Adjust the ForceHow and When to Adjust the Forces Test the Down close forceImportant safety check Test the Safety Reverse SystemTest the Protector System Care of Your Opener Maintenance ScheduleLimit and Force Adjustment Controls Remote control batteryManual disconnect Position To open the door manually Operation of Your OpenerOperation of the Multi-Function Door Control Outside Keylock or Keyless EntryReceiver and Remote Control Programming Are the wiring connections correct? Review , Having a Problem?Situation Probable Cause & Solution Door control, a short under the staples, or a broken wireBulb if regular bulb burns out Is the Light feature on? Turn it offRail Assembly Parts Repair PartsInstallation Parts Complete with Opener Assembly PartsAccessories Available for your Opener Index Chamberlain Service Is on Call

8200 1/2 HP specifications

The Chamberlain 8200 is a robust and efficient garage door opener that combines power, reliability, and advanced technology to provide homeowners with a seamless experience. With its 1/2 HP motor, this opener is designed to handle sectional doors weighing up to 500 pounds, making it suitable for a variety of garage doors.

One of the standout features of the Chamberlain 8200 is its strong motor, which ensures smooth and quiet operation. This is particularly important for homeowners who have living spaces adjacent to the garage, as the reduced noise levels contribute to a more comfortable environment. The motor is also designed for durability and long-lasting performance, ensuring that it will consistently meet the needs of the user over time.

The Chamberlain 8200 comes equipped with the innovative MyQ technology, which enables users to control their garage door opener remotely via a smartphone app. This feature not only provides convenience but also enhances security, allowing homeowners to monitor and manage their garage door from anywhere. Whether you’re on vacation or simply at work, the ability to check the status of your garage door gives peace of mind.

Safety is another priority with the Chamberlain 8200, which includes features such as the patented Security+ 2.0 technology. This system ensures that your garage door opener transmits a new code every time the remote control is used, significantly reducing the risk of unauthorized access. Additionally, the opener is equipped with safety sensors that detect any obstructions in the door's path, preventing accidents or injuries.

Installation of the Chamberlain 8200 is straightforward, thanks to its detailed instructions and user-friendly design. The unit is compatible with a variety of garage door types and can easily integrate with existing door systems.

Overall, the Chamberlain 8200 1/2 HP garage door opener stands out as a powerful, technologically advanced solution for homeowners seeking convenience and security. Its blend of performance, innovative features, and user-friendly design makes it a top choice for modern garage door automation. Whether you are looking to upgrade your current system or installing a new opener, the Chamberlain 8200 promises reliability and peace of mind.
Top Page Image Contents