Chamberlain 8200 1/2 HP Start by reviewing these important safety alert symbols, Contents

Page 2

Contents

Page

A review of safety alert symbols

2

You'll need tools

3

Safety information regarding garage door

 

locks and ropes

3

Testing your garage door for sticking,

 

binding and balance

3

Illustration of sectional door installation

4

Illustration of one-piece door installation

5

Carton inventory

6

Hardware inventory

7

Assembly section – pages 8 - 11

 

Assemble T-rail

8

Attach belt pulley bracket

8

Install trolley

9

Fasten T-rail to opener

9

Install belt

10

Set the belt tension

10

Attach belt cap retainer

11

Installation section – pages 11 - 27

 

Installation safety instructions

11

Determine header bracket location

 

Sectional door

12

One-piece door

13

Install the header bracket

14

Attach the T-rail to header bracket

15

Position the opener

16

Hang the opener

17

Install the multi-function door control panel

18

Contents

Page

Install the lights and lenses

19

Attach manual release rope and handle

19

Electrical requirements

20

The Protector System®

21

Install the safety reversing sensor

22, 23

Fasten door bracket (sectional door)

24

Fasten door bracket (one-piece door)

25

Connect door arm to trolley (sectional door)

26

Connect door arm to trolley (one-piece door)

27

Adjustment section – pages 28 - 30

 

Travel limit adjustments

28

Force adjustments

29

Test the Protector System®

30

Test the safety reverse system

30

Operation safety instructions

31

Care of your opener

31

Maintenance schedule

31

Operation of your opener

32

Receiver and remote control programming

33

Having a problem?

34, 35

Repair parts, rail assembly

36

Repair parts, installation

36

Repair parts, opener assembly

37

Accessories

38

Index

39

How to order repair parts

40

Warranty

40

Start by reviewing these important safety alert symbols

When you see these Safety Symbols on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the corresponding instructions. The hazard may come from something mechanical or from electric shock. Read the instructions carefully.

WARNING

Mechanical

WARNING

Electrical

When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the corresponding instructions. Read the instructions carefully.

CAUTION

This garage door opener is designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the safety instructions contained in this manual.

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Garage Door Opener Model 8200 Series Assembly section pages 8 Start by reviewing these important safety alert symbolsContents Installation section pages 11Youll Need Tools Sectional Door Installation Closed PositionOne-Piece Door With Track ONE-PIECE Door InstallationOne-Piece Door without Track Carton Inventory SecurityAssembly Attach the Belt Pulley Bracket Assembly Section Pages 8Assembly Step Right WrongInstall the Trolley on the T-rail Faster the T-rail to the OpenerDo not use any tools Install the Belt & Set the Belt TensionCheck to make sure the belt is not twisted Attach the Belt Cap Retainer To attach the belt cap retainerSectional Door ONE-PIECE Door With Track Installation Section Pages 12 Installation StepDetermine Header Bracket Location Proceed to ,One-piece door without track Pivot hardware ExampleOne-piece door without track Jamb hardware =12Fasten the Header Bracket to the Ceiling Install the Header BracketFasten the Header Bracket to the Wall Attach the T-rail to the Header Bracket Raise the opener onto a stepladder Position the OpenerSectional Door & ONE-PIECE Door with Track Surface where Hang the OpenerGrease the top Underside of the rail Trolley slides with rail greaseTo opener terminal screws white to 2 white/red to Install the Multi-Function Door Control PanelOutside Keylock Accessory Connections See Safety Reversing Sensor Instructions beginning on Install the Lights and the Lenses32 explains how to use the door control Reverse the procedure to remove the lensesPermanent Wiring Connection Electrical RequirementsProtector System Facing the door from inside the garageInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Sectional Door Installation Procedure Fasten Door BracketHeader Wall Hole Alignment Alternative Connect Door Arm to TrolleySectional Doors Only Adjustment Procedures for One-Piece Doors All ONE-PIECE DoorsHow and When to Adjust the Limits Adjustment Section Pages 28 Adjustment StepAdjust the UP and Down Limits Test the Down close force Adjust the ForceHow and When to Adjust the Forces Test the UP open forceTest the Protector System Test the Safety Reverse SystemImportant safety check Remote control battery Maintenance ScheduleLimit and Force Adjustment Controls Care of Your OpenerOutside Keylock or Keyless Entry Operation of Your OpenerOperation of the Multi-Function Door Control Manual disconnect Position To open the door manuallyReceiver and Remote Control Programming Door control, a short under the staples, or a broken wire Having a Problem?Situation Probable Cause & Solution Are the wiring connections correct? Review ,Is the Light feature on? Turn it off Bulb if regular bulb burns outInstallation Parts Repair PartsRail Assembly Parts Opener Assembly Parts Complete withAccessories Available for your Opener Index Chamberlain Service Is on Call

8200 1/2 HP specifications

The Chamberlain 8200 is a robust and efficient garage door opener that combines power, reliability, and advanced technology to provide homeowners with a seamless experience. With its 1/2 HP motor, this opener is designed to handle sectional doors weighing up to 500 pounds, making it suitable for a variety of garage doors.

One of the standout features of the Chamberlain 8200 is its strong motor, which ensures smooth and quiet operation. This is particularly important for homeowners who have living spaces adjacent to the garage, as the reduced noise levels contribute to a more comfortable environment. The motor is also designed for durability and long-lasting performance, ensuring that it will consistently meet the needs of the user over time.

The Chamberlain 8200 comes equipped with the innovative MyQ technology, which enables users to control their garage door opener remotely via a smartphone app. This feature not only provides convenience but also enhances security, allowing homeowners to monitor and manage their garage door from anywhere. Whether you’re on vacation or simply at work, the ability to check the status of your garage door gives peace of mind.

Safety is another priority with the Chamberlain 8200, which includes features such as the patented Security+ 2.0 technology. This system ensures that your garage door opener transmits a new code every time the remote control is used, significantly reducing the risk of unauthorized access. Additionally, the opener is equipped with safety sensors that detect any obstructions in the door's path, preventing accidents or injuries.

Installation of the Chamberlain 8200 is straightforward, thanks to its detailed instructions and user-friendly design. The unit is compatible with a variety of garage door types and can easily integrate with existing door systems.

Overall, the Chamberlain 8200 1/2 HP garage door opener stands out as a powerful, technologically advanced solution for homeowners seeking convenience and security. Its blend of performance, innovative features, and user-friendly design makes it a top choice for modern garage door automation. Whether you are looking to upgrade your current system or installing a new opener, the Chamberlain 8200 promises reliability and peace of mind.
Top Page Image Contents