Harman-Kardon AVR 146 Step Six Plug in AC Power, Step Seven Insert Batteries in Remote

Page 24

INSTALLATION

If you used an HDMI video connection for any of your sources, then connect the HDMI Output on the AVR to an HDMI input on your video display. See Figure 29. As mentioned previously, you will need to make a separate digital audio connection from each source device to the AVR 146, and you will also need to consult the owner’s guide for your television to learn the proper procedure for disabling or muting the audio.

Insert the batteries as shown in Figure 32, making sure to observe the correct polarity.

Figure 29 – HDMI Output

If you used component video for any sources, connect the Component Video Monitor outputs on the receiver to one set of component video inputs on your display. See Figure 30. Make a note of how these inputs are labeled on the display.

Figure 30 – Component Video Monitor Outputs

If you used S-video for any sources, or if all of your sources used HDMI or component video, connect the S-video Monitor output on the receiver to an S-video input on your display. See Figure 31. Make a note of how the input is labeled.

If you used composite video for any sources, connect the composite video Monitor output on the receiver to a composite video input on the display. See Figure 31. Again, make a note of how this input is labeled on the display.

Figure 31 – S-Video and Composite Video Monitor Outputs

Consult the manual for your TV to make sure you understand how to select each video input. As you play different source devices that use different types of video connections, select the correct video input on your video display.

Step Six – Plug in AC Power

Having made all of your wiring connections, it is now time to plug each component’s AC power cord into a working outlet.

Before plugging the AVR 146’s AC Power Cord into an electrical outlet, make sure that the Master Power Switch on the front panel is popped out so that the word OFF appears on its top. Gently press the button to turn the switch off. This will prevent the possibility of damaging the AVR in case of a transient power surge.

Step Seven – Insert Batteries in Remote

The AVR 146 remote control uses three AAA batteries, which are included.

To remove the battery cover located on the back of the remote, firmly press the ridged depression and slide the cover towards the top of the remote.

Figure 32 – Remote Battery Compartment

When using the remote, remember to point the lens toward the front panel of the AVR 146. Make sure no objects, such as furniture, are blocking the remote’s path to the receiver. Bright lights, fluorescent lights and plasma video displays may interfere with the remote’s functioning. The remote has a range of about 20 feet, depending on the lighting conditions. It may be used at an angle of up to 30 degrees to either side of the AVR.

If the remote seems to operate intermittently, or if pressing a button on the remote does not cause the AVR Selector or one of the Input Selectors to light up, then make sure the batteries have been inserted correctly, or replace all three batteries with fresh ones.

Step Eight – Program Sources Into the Remote

The AVR 146 remote not only is capable of controlling the receiver, but it may also be programmed to control many brands and models of VCRs, DVD players, CD players, cable boxes, satellite receivers, cassette decks and TVs, as well as an iPod docked in The Bridge.

It may help to think of the remote as a book with pages. Each page represents the button functions for a different device. In order to access the functions for a particular device, you first need to turn to that page, that is, switch the remote to that device mode. This is done by pressing the AVR Button to access the codes that control the receiver, or the Input Selector buttons to access the codes for the devices programmed into the remote.

You may have noticed that three of the Input Selectors look different from the others (see Figure 33). For the DVD/CD, TAPE/The Bridge and HDMI 1/HDMI 2 Selectors, there is a primary source, whose name is printed on the button, and a secondary source, whose name is printed in green above the button. To access the code set for the primary source (which also selects that source input on the AVR and turns on the AVR), press the Input Selector once. The Input Selector will light in red to indicate that the primary source is active.

To access the code set for the secondary source (which also selects that source input on the AVR and turns on the AVR), press the Input Selector a second time. The Input Selector will light in green to indicate that the secondary source is active.

The AVR 146’s remote is factory-programmed to control an iPod docked in The Bridge and many Harman Kardon DVD and CD players. If you have other source devices in your system, follow these steps to program the correct codes into the remote.

24

Image 24
Contents AVR Safety Information Outdoor Antenna Grounding. If an outside antennaImportant Safety Information Staple Invoice Here Table of Contents Introduction Thank you for choosing Harman KardonAudio Section Surround ModesSupplied Accessories Audio InputsAudio/Video Inputs With S-Video Digital Audio InputsFRONT-PANEL Controls Input Indicators REAR-PANEL Connections Video Component FM Antenna InputsOutputs Input VideoRemote Control Functions Channel Input Selector Press this button to selectBridge/DMP Controls an iPod docked in The Bridge Power On AVR SelectorRemote Control Functions Introduction to Home Theater Surround ModesTypical Home Theater System Multichannel AudioConnecting Source Devices to the AVR ConnectionsSpeaker Connections SubwooferAudio Connections Digital AudioVideo Connections Analog AudioFM antenna uses a 75-ohm F-connector. See Figure AntennasAnalog Video Is colored red. See FigureSpeaker Placement Installation Step One Connect the SpeakersStep Two Connect the Subwoofer Step Three Connect the AntennasDevice Type Audio Connections Video ConnectionsTiVo or other Or Video 1 Composite Video Input Coax digital output Component video connections at allVideo 1 Source Video 2 SourceVideo 3 Source Step Five Connect the Video Display Hdmi 1 SourceHdmi 2 Source No video connections are neededStep Six Plug in AC Power Step Seven Insert Batteries in RemoteTurn on your source device Enter a code from aboveVideo Cable, Satellite Cable/SatelliteStep Nine Turn On the AVR Two steps are required the first time you turn on the AVRInitial Setup Using the On-Screen Menu SystemStep One Determine Speaker Size Step Three Manual Setup Menu Step Two Measure Speaker DistancesSpeaker Size Menu Is not present, such as when a DVD is paused Speaker Crossover MenuDelay Adjust Menu Step Four Output Level CalibrationSee Figure Using the Remote Control With Source Material Using the Full-OSD MenuStep Five Configure Sources Tuner at this timeInput Setup Menu Screen for DMP/The Bridge source Sleep Timer Volume ControlOperation Turning On the AVRHeadphones Mute FunctionTone Controls Source SelectionWhen you wish to view a DVD, simply select the DVD source Audio Input SelectionVideo Input Selection Channel Direct InputsUsing the Tuner Channel Input SelectorUsing TheBridgeTM RecordingSelecting a Surround Mode Select a Surround Mode RemoteAnalog Audio Signals Digital Audio SignalsAdvanced Functions Audio Processing and Surround SoundSurround Modes Dolby Surround Settings Default ModesProvides descriptions of all surround modes available on Panorama adjusts wraparound surround effect 0 orDolby Digital EX played as Passages to avoid disturbing othersSurround Mode Description Incoming Bitstream or Signal System Settings Advanced Remote Control FunctionsDim Function Punch-Through ProgrammingPress the Power Off Button to program the Power Off command To program, or record a macro, follow these stepsTo program punch-through control while operating any device Processor Reset Resetting the RemoteMemory Troubleshooting Guide AVR 146 Technical Specifications DTSAppendix Default settings, worksheets, remote product codes Table A1 Source Input Setting DefaultsTable A2 Speaker/Channel Setting Defaults Table A3 Delay Setting DefaultsTable A4 Source Input Settings Table A5 Speaker/Channel SettingsTable A6 Remote Control Codes Table A7 System SettingsFeature Default Setting Your Setting Off Volume Default Default Vol Set 25dBTable A8 Remote Control Function List TV VID3Remote Control Function List Table A8Aiwa Table A9 Table A10Table A11 Remote Control Product Codes CD Table A12 Remote Control Product Codes DVDTable A14 Remote Control Product Codes Tape Table A15 Remote Control Product Codes CBLTable A16 Remote Control Product Codes Table A15
Related manuals
Manual 1 pages 4.96 Kb

AVR 146 specifications

The Harman-Kardon AVR 146 is a versatile audio-video receiver designed to elevate home entertainment experiences. A product of the renowned Harman-Kardon brand, this receiver combines advanced audio technologies, user-friendly features, and sleek design, making it a popular choice for audiophiles and casual listeners alike.

One of the standout characteristics of the AVR 146 is its power output. It delivers 50 watts per channel across seven channels, allowing it to easily drive a wide range of speakers while ensuring that dynamic soundscapes are reproduced with clarity and depth. This capability makes it suitable for both movies and music, enhancing the overall auditory experience in home theater setups.

The AVR 146 supports high-definition audio formats, including Dolby TrueHD and DTS-HD Master Audio. These formats provide lossless sound quality, allowing listeners to appreciate every nuance of their favorite films and albums. The receiver's support for a 7.1 channel layout enriches movie nights with a surround sound experience, drawing viewers deeper into the action.

Connectivity is another key feature of the AVR 146. It is equipped with multiple HDMI inputs, allowing users to connect several high-definition devices such as Blu-ray players, gaming consoles, and streaming devices. This ensures that users can enjoy high-quality audio and video without the need for constant plug-and-play. Additionally, the receiver features an array of analog and digital inputs, which further broaden its compatibility with various devices.

Setup and operation are simplified by the inclusion of the user-friendly on-screen graphical interface. This intuitive design makes it easy to navigate through the various settings and features, allowing users to customize their audio preferences with ease. The AVR 146 also incorporates the Harman Kardon Quick Select feature, which allows users to save their favorite settings for different sources for quick access.

In terms of design, the Harman-Kardon AVR 146 showcases a modern and elegant appearance synonymous with the brand's aesthetic. It features a sleek front panel with an easy-to-read display and well-organized buttons, blending seamlessly into home environments.

In summary, the Harman-Kardon AVR 146 is a well-rounded audio-video receiver that promises exceptional performance and versatility. With its combination of powerful amplification, support for advanced audio formats, extensive connectivity options, and a user-friendly interface, it is an excellent choice for anyone looking to enhance their home entertainment system. Whether for movie enthusiasts or music lovers, the AVR 146 delivers an auditory experience that impresses and satisfies.