Harman-Kardon AVR 146 owner manual Operation, Turning On the AVR, Sleep Timer, Volume Control

Page 34

OPERATION

Now that you have installed your system components and completed at least a basic configuration of your receiver, you are ready to begin enjoying your home theater system.

Turning On the AVR 146

Gently press the Master Power Switch until the word OFF is no longer visible. The Power Indicator above the two power switches should light up in amber. This indicates that the AVR is in Standby mode and is ready to be turned on. Normally, you may leave the Master Power Switch in the ON position, even when the receiver is not being used. See Figure 50.

Figure 50 – Power Switches

There are several ways in which the AVR 146 may be turned on:

a)Press the Standby/On Switch on the front panel. See Figure 50.

b)Press the Source Select Button on the front panel. See Figure 51.

Figure 51 – Source Select Button/The Bridge

c)Using the remote, press any one of these buttons: AVR, DVD/CD, TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2, VID3, AM/FM or 6CH. See Figure 52.

Figure 52 – AVR and Input Selectors

NOTE: Any time you press one of the remote’s Input Selectors (i.e., DVD/CD, TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2, VID3, AM/FM or 6CH), the remote will switch modes so that it will only transmit the codes programmed to operate that device. To control the receiver, press the AVR Button to return the remote to AVR mode.

To turn the receiver off, press either the Standby/On Switch on the

front panel, or press the AVR Button and the OFF Button on the remote. Unless the receiver will not be used for an extended period of time (for example, if you will be on vacation), it is not necessary to turn off the Master Power Switch. When the Master Power Switch is turned off, any settings you have programmed, including system configuration and preset radio stations, will be preserved for up to four weeks.

Sleep Timer

You may program the AVR to play for up to 90 minutes and then turn off automatically using the sleep timer.

Press the Sleep Button on the remote, and the time until turn-off will be displayed. See Figure 53. Each additional press of the Sleep Button will reduce the time until turn-off by 10 minutes, until the OFF setting is reached, which disables the sleep timer.

Figure 53 – Sleep Button

When the sleep timer has been set, the front-panel display will automati- cally dim to half-brightness. If you press any button on the remote or front panel, the display will return to full-brightness. The display will dim again several seconds after your last command.

If you press the Sleep Button after the timer has been set, the remaining time until turn-off will be displayed. You may press the Sleep Button to change the time until turn-off. Pressing and holding the Sleep Button will disable the sleep timer, and the SLEEP OFF message will appear.

Volume Control

The volume may be adjusted either by turning the knob on the front panel (clockwise to increase volume or counterclockwise to decrease volume), or by pressing the Volume Control Buttons on the remote. See Figure 54. The volume is displayed as a negative number of decibels (dB) below the 0dB reference point, and may be changed in 0.5dB increments.

Unlike the volume controls on some other products, 0dB is the maximum volume for the AVR 146. Although it’s physically possible to turn the volume to a higher level, doing so may damage your hearing and your speakers. For certain more dynamic audio materials, even 0dB may be too high, allowing for damage to equipment.

Figure 54 – Volume Controls

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents AVR Safety Information Outdoor Antenna Grounding. If an outside antennaImportant Safety Information Staple Invoice Here Table of Contents Audio Section IntroductionThank you for choosing Harman Kardon Surround ModesAudio/Video Inputs With S-Video Supplied AccessoriesAudio Inputs Digital Audio InputsFRONT-PANEL Controls Input Indicators REAR-PANEL Connections Outputs Input Video ComponentFM Antenna Inputs VideoChannel Input Selector Press this button to select Remote Control FunctionsBridge/DMP Controls an iPod docked in The Bridge Power On AVR SelectorRemote Control Functions Typical Home Theater System Introduction to Home TheaterSurround Modes Multichannel AudioSpeaker Connections Connecting Source Devices to the AVRConnections SubwooferVideo Connections Audio ConnectionsDigital Audio Analog AudioAnalog Video FM antenna uses a 75-ohm F-connector. See FigureAntennas Is colored red. See FigureSpeaker Placement Step Two Connect the Subwoofer InstallationStep One Connect the Speakers Step Three Connect the AntennasTiVo or other Or Video 1 Composite Video Input Device TypeAudio Connections Video Connections Coax digital output Component video connections at allVideo 2 Source Video 1 SourceVideo 3 Source Hdmi 2 Source Step Five Connect the Video DisplayHdmi 1 Source No video connections are neededStep Six Plug in AC Power Step Seven Insert Batteries in RemoteVideo Cable, Satellite Turn on your source deviceEnter a code from above Cable/SatelliteStep Nine Turn On the AVR Two steps are required the first time you turn on the AVRUsing the On-Screen Menu System Initial SetupStep One Determine Speaker Size Step Two Measure Speaker Distances Step Three Manual Setup MenuSpeaker Size Menu Is not present, such as when a DVD is paused Speaker Crossover MenuStep Four Output Level Calibration Delay Adjust MenuSee Figure Using the Remote Control With Source Material Using the Full-OSD MenuStep Five Configure Sources Tuner at this timeInput Setup Menu Screen for DMP/The Bridge source Operation Sleep TimerVolume Control Turning On the AVRTone Controls HeadphonesMute Function Source SelectionVideo Input Selection When you wish to view a DVD, simply select the DVD sourceAudio Input Selection Channel Direct InputsUsing the Tuner Channel Input SelectorUsing TheBridgeTM RecordingSelecting a Surround Mode Select a Surround Mode RemoteAdvanced Functions Analog Audio SignalsDigital Audio Signals Audio Processing and Surround SoundSurround Modes Default Modes Dolby Surround SettingsProvides descriptions of all surround modes available on Dolby Digital EX played as Panorama adjusts wraparound surround effect0 or Passages to avoid disturbing othersSurround Mode Description Incoming Bitstream or Signal Dim Function System SettingsAdvanced Remote Control Functions Punch-Through ProgrammingTo program, or record a macro, follow these steps Press the Power Off Button to program the Power Off commandTo program punch-through control while operating any device Resetting the Remote Processor ResetMemory Troubleshooting Guide AVR 146 Technical Specifications DTSTable A2 Speaker/Channel Setting Defaults Appendix Default settings, worksheets, remote product codesTable A1 Source Input Setting Defaults Table A3 Delay Setting DefaultsTable A4 Source Input Settings Table A5 Speaker/Channel SettingsFeature Default Setting Your Setting Table A6 Remote Control CodesTable A7 System Settings Off Volume Default Default Vol Set 25dBTable A8 Remote Control Function List TV VID3Remote Control Function List Table A8Aiwa Table A9 Table A10Table A11 Remote Control Product Codes CD Table A12 Remote Control Product Codes DVDTable A14 Remote Control Product Codes Tape Table A15 Remote Control Product Codes CBLTable A16 Remote Control Product Codes Table A15
Related manuals
Manual 1 pages 4.96 Kb

AVR 146 specifications

The Harman-Kardon AVR 146 is a versatile audio-video receiver designed to elevate home entertainment experiences. A product of the renowned Harman-Kardon brand, this receiver combines advanced audio technologies, user-friendly features, and sleek design, making it a popular choice for audiophiles and casual listeners alike.

One of the standout characteristics of the AVR 146 is its power output. It delivers 50 watts per channel across seven channels, allowing it to easily drive a wide range of speakers while ensuring that dynamic soundscapes are reproduced with clarity and depth. This capability makes it suitable for both movies and music, enhancing the overall auditory experience in home theater setups.

The AVR 146 supports high-definition audio formats, including Dolby TrueHD and DTS-HD Master Audio. These formats provide lossless sound quality, allowing listeners to appreciate every nuance of their favorite films and albums. The receiver's support for a 7.1 channel layout enriches movie nights with a surround sound experience, drawing viewers deeper into the action.

Connectivity is another key feature of the AVR 146. It is equipped with multiple HDMI inputs, allowing users to connect several high-definition devices such as Blu-ray players, gaming consoles, and streaming devices. This ensures that users can enjoy high-quality audio and video without the need for constant plug-and-play. Additionally, the receiver features an array of analog and digital inputs, which further broaden its compatibility with various devices.

Setup and operation are simplified by the inclusion of the user-friendly on-screen graphical interface. This intuitive design makes it easy to navigate through the various settings and features, allowing users to customize their audio preferences with ease. The AVR 146 also incorporates the Harman Kardon Quick Select feature, which allows users to save their favorite settings for different sources for quick access.

In terms of design, the Harman-Kardon AVR 146 showcases a modern and elegant appearance synonymous with the brand's aesthetic. It features a sleek front panel with an easy-to-read display and well-organized buttons, blending seamlessly into home environments.

In summary, the Harman-Kardon AVR 146 is a well-rounded audio-video receiver that promises exceptional performance and versatility. With its combination of powerful amplification, support for advanced audio formats, extensive connectivity options, and a user-friendly interface, it is an excellent choice for anyone looking to enhance their home entertainment system. Whether for movie enthusiasts or music lovers, the AVR 146 delivers an auditory experience that impresses and satisfies.
Top Page Image Contents