Harman-Kardon AVR 146 owner manual To program, or record a macro, follow these steps

Page 46

ADVANCED FUNCTIONS

certain groups of controls to operate another component. For example, while using the AVR to control surround modes and other audio functions, you may operate the transport controls of your DVD player. Or while using the remote to control video functions on your TV, you may use your cable box to change channels and the AVR to control the volume.

NOTE: It is not necessary to program the remote to control your DVD player’s transport controls while the AVR, VID2 or VID3 devices are in use, as the remote is preprogrammed at the factory with this function.

To program punch-through control while operating any device:

1.Press and hold the Input Selector (or AVR selector) for the main device the remote will be operating until the Program LED flashes and the remote enters Program mode.

2.Select the type of punch-through programming.

a)To program volume control punch-through, press the Volume Up Button.

b)To program channel control punch-through, press the Volume Down Button.

c)To program transport control punch-through, press the Play Button.

3.Press the Input Selector (or AVR Selector) for the device whose volume, channel or transport controls you would like to be active while operating the device you selected in the first step. The LED will flash green to confirm the programming.

For example, if you wish to watch your TV (programmed into the Video 3 Button) while changing channels using your cable box (Video 2), first press and hold the Video 3 Button until the LED flashes. Then press the Volume Down Button, followed by the Video 2 Button.

To undo punch-through programming, follow the same steps as above, but press the same Input (or AVR) Selector in Steps 1 and 3.

You may reassign the transport control punch-through programming for the AVR, VID2 and VID3 devices to other devices, such as CD. If you wish to remove transport control punch-through altogether for the AVR, VID2 or VID3 device, follow the same procedure as for programming punch-through, but in Step 3 press either of the other two of these three special selector buttons. For example, to remove punch-through transport control from the VID3 device so that pressing any of the transport controls will have no effect, press and hold VID3 and the Mute Button until the Program Indicator LED flashes in amber, then press the Play Button, followed by either the AVR or VID2 Button.

Macros

Macros are used to program sequences of up to 19 commands that are executed with a single button press. Macros are well suited for power on and off commands, or to send out a favorite multidigit channel number with one button press, or to have the ability to send out a code sequence to control another device while the remote is operating one device but with more flexibility than the built-in punch-through controls.

Some commands may not be programmed into macros: Mute, Dim, Channel Up/Down or any of the surround mode commands.

NOTE: Use caution when programming complicated macros. It isn’t possible to program a pause or delay before sending commands after Power On, and the component may not be ready to respond to commands instantaneously after powering on.

To program, or “record” a macro, follow these steps:

1.Simultaneously press one of the four Macro Buttons or the Power On Button and the Mute Button to enter program mode.

2.Press the Input (or AVR) Selector for each device before you enter commands to be transmitted to that device. This step counts as one of the 19 commands allowed for each macro.

3.For the Power On command, DO NOT press the Power On Button. Press the Mute Button instead.

4.Press the Power Off Button to program the Power Off command.

5.Press the Sleep Button to end the programming process.

It isn’t possible to “edit” a command within a macro. However, you may erase the macro as follows:

1.Simultaneously press and hold the Mute Button and the Macro Button containing the macro until the LED flashes.

2.Press the Surround Button to erase the macro.

Here are two macros that you may find useful when listening to an iPod docked in The Bridge:

The purpose of the first macro is to access the DMP SETTING menu (Figure 49) while listening to The Bridge with one button press.

1.Simultaneously press and hold the M1(or other unused) Macro Button and the Mute Button until the Program LED flashes.

2.Press the AVR Button (the first command switches the remote to AVR mode).

3.Press the OSD Button (the second command activates the on-screen menu system).

4.Press the Set Button (the third command selects the INPUT SETUP menu; this macro assumes the current source is The Bridge).

5.Press the ¤ Button three times (the fourth, fifth and sixth commands navigate to the GO TO DMP SETTING line).

6.Press the Set Button again (the seventh command selects the DMP SETTING menu).

7.Press the Sleep Button to end the programming process. You have now programmed the first macro, which will display the DMP SETTING menu after you have selected The Bridge as your source input.

After you have made your selections in the DMP SETTING menu, such as turning on repeat playback or shuffle mode, the second macro

46

Image 46
Contents AVR Safety Information Outdoor Antenna Grounding. If an outside antennaImportant Safety Information Staple Invoice Here Table of Contents Audio Section IntroductionThank you for choosing Harman Kardon Surround ModesAudio/Video Inputs With S-Video Supplied AccessoriesAudio Inputs Digital Audio InputsFRONT-PANEL Controls Input Indicators REAR-PANEL Connections Outputs Input Video ComponentFM Antenna Inputs VideoChannel Input Selector Press this button to select Remote Control FunctionsBridge/DMP Controls an iPod docked in The Bridge Power On AVR SelectorRemote Control Functions Typical Home Theater System Introduction to Home TheaterSurround Modes Multichannel AudioSpeaker Connections Connecting Source Devices to the AVRConnections SubwooferVideo Connections Audio ConnectionsDigital Audio Analog AudioAnalog Video FM antenna uses a 75-ohm F-connector. See FigureAntennas Is colored red. See FigureSpeaker Placement Step Two Connect the Subwoofer InstallationStep One Connect the Speakers Step Three Connect the AntennasTiVo or other Or Video 1 Composite Video Input Device TypeAudio Connections Video Connections Coax digital output Component video connections at allVideo 2 Source Video 1 SourceVideo 3 Source Hdmi 2 Source Step Five Connect the Video DisplayHdmi 1 Source No video connections are neededStep Six Plug in AC Power Step Seven Insert Batteries in RemoteVideo Cable, Satellite Turn on your source deviceEnter a code from above Cable/SatelliteStep Nine Turn On the AVR Two steps are required the first time you turn on the AVRUsing the On-Screen Menu System Initial SetupStep One Determine Speaker Size Step Two Measure Speaker Distances Step Three Manual Setup MenuSpeaker Size Menu Is not present, such as when a DVD is paused Speaker Crossover MenuStep Four Output Level Calibration Delay Adjust MenuSee Figure Using the Remote Control With Source Material Using the Full-OSD MenuStep Five Configure Sources Tuner at this timeInput Setup Menu Screen for DMP/The Bridge source Operation Sleep TimerVolume Control Turning On the AVRTone Controls HeadphonesMute Function Source SelectionVideo Input Selection When you wish to view a DVD, simply select the DVD sourceAudio Input Selection Channel Direct InputsUsing the Tuner Channel Input SelectorUsing TheBridgeTM RecordingSelecting a Surround Mode Select a Surround Mode RemoteAdvanced Functions Analog Audio SignalsDigital Audio Signals Audio Processing and Surround SoundSurround Modes Default Modes Dolby Surround SettingsProvides descriptions of all surround modes available on Dolby Digital EX played as Panorama adjusts wraparound surround effect0 or Passages to avoid disturbing othersSurround Mode Description Incoming Bitstream or Signal Dim Function System SettingsAdvanced Remote Control Functions Punch-Through ProgrammingTo program, or record a macro, follow these steps Press the Power Off Button to program the Power Off commandTo program punch-through control while operating any device Resetting the Remote Processor ResetMemory Troubleshooting Guide AVR 146 Technical Specifications DTSTable A2 Speaker/Channel Setting Defaults Appendix Default settings, worksheets, remote product codesTable A1 Source Input Setting Defaults Table A3 Delay Setting DefaultsTable A4 Source Input Settings Table A5 Speaker/Channel SettingsFeature Default Setting Your Setting Table A6 Remote Control CodesTable A7 System Settings Off Volume Default Default Vol Set 25dBTable A8 Remote Control Function List TV VID3Remote Control Function List Table A8Aiwa Table A9 Table A10Table A11 Remote Control Product Codes CD Table A12 Remote Control Product Codes DVDTable A14 Remote Control Product Codes Tape Table A15 Remote Control Product Codes CBLTable A16 Remote Control Product Codes Table A15
Related manuals
Manual 1 pages 4.96 Kb

AVR 146 specifications

The Harman-Kardon AVR 146 is a versatile audio-video receiver designed to elevate home entertainment experiences. A product of the renowned Harman-Kardon brand, this receiver combines advanced audio technologies, user-friendly features, and sleek design, making it a popular choice for audiophiles and casual listeners alike.

One of the standout characteristics of the AVR 146 is its power output. It delivers 50 watts per channel across seven channels, allowing it to easily drive a wide range of speakers while ensuring that dynamic soundscapes are reproduced with clarity and depth. This capability makes it suitable for both movies and music, enhancing the overall auditory experience in home theater setups.

The AVR 146 supports high-definition audio formats, including Dolby TrueHD and DTS-HD Master Audio. These formats provide lossless sound quality, allowing listeners to appreciate every nuance of their favorite films and albums. The receiver's support for a 7.1 channel layout enriches movie nights with a surround sound experience, drawing viewers deeper into the action.

Connectivity is another key feature of the AVR 146. It is equipped with multiple HDMI inputs, allowing users to connect several high-definition devices such as Blu-ray players, gaming consoles, and streaming devices. This ensures that users can enjoy high-quality audio and video without the need for constant plug-and-play. Additionally, the receiver features an array of analog and digital inputs, which further broaden its compatibility with various devices.

Setup and operation are simplified by the inclusion of the user-friendly on-screen graphical interface. This intuitive design makes it easy to navigate through the various settings and features, allowing users to customize their audio preferences with ease. The AVR 146 also incorporates the Harman Kardon Quick Select feature, which allows users to save their favorite settings for different sources for quick access.

In terms of design, the Harman-Kardon AVR 146 showcases a modern and elegant appearance synonymous with the brand's aesthetic. It features a sleek front panel with an easy-to-read display and well-organized buttons, blending seamlessly into home environments.

In summary, the Harman-Kardon AVR 146 is a well-rounded audio-video receiver that promises exceptional performance and versatility. With its combination of powerful amplification, support for advanced audio formats, extensive connectivity options, and a user-friendly interface, it is an excellent choice for anyone looking to enhance their home entertainment system. Whether for movie enthusiasts or music lovers, the AVR 146 delivers an auditory experience that impresses and satisfies.