Harman-Kardon AVR 146 Installation, Step One Connect the Speakers, Step Two Connect the Subwoofer

Page 20

INSTALLATION

You are now ready to connect your various components to your receiver. Before beginning, make sure that all components, including the AVR 146, are turned completely off and their power cords are unplugged. Don’t plug any of the power cords back in until you have finished making all of your connections.

Remember that your receiver generates heat while it is on. Select a location that leaves several inches of space on all sides of the receiver. It is preferable to avoid completely enclosing the receiver inside an unventilated cabinet. It is also preferable to place components on separate shelves rather than stacking them directly on top of the receiver. Some surface finishes are delicate. Try to select a location with a sturdy surface finish.

Step One – Connect the Speakers

If you have not yet done so, place your speakers in the listening room as described in the Speaker Placement section above.

Connect the center, front left, front right, surround left and surround right loudspeakers to the corresponding speaker terminals on the AVR 146. See Figure 16. Remember to maintain the proper polarity by always connecting the positive and negative terminals on each speaker to the positive and negative terminals on the receiver. Use the Connection Color Guide on page 16 as a reference.

C

AVR 146

FR

FL

SR

SL

Figure 16 – Speaker Connections

Step Two – Connect the Subwoofer

Connect the Subwoofer Output on the AVR 146 to the line-level input on your subwoofer. See Figure 17. Consult the manufacturer’s guide for the subwoofer for additional information.

AVR 146

SUB

Figure 17 – Subwoofer Connection

Step Three – Connect the Antennas

Connect the FM and AM antennas to their terminals. See Figure 18.

AVR 146

AM

FM

Figure 18 – Antenna Connections

Step Four – Connect the Source Components

Use the Table A4 worksheet in the Appendix to note which connections you will use for each of your source devices.

For each source, select a source input (Video 1, Video 2, Video 3, etc.). In Table 2 we recommend connecting certain types of sources to specific source inputs to make it easier to program and use the remote control.

Decide which audio connections you will use. If a source device has them, use either the coaxial digital or the optical digital audio connection. Referring to Table 2, we recommend you connect the DVD source to the Coaxial 1 input jack, and the source designated Video 2 to the Optical 2 input jack. However, you may make whatever connections are best for your system.

In addition to the digital audio connections, we recommend that you connect the analog audio connections for each source, as a backup to the digital connections. For sources that don’t have digital audio outputs, you must use the analog audio connections.

For each video source, select one type of video connection. HDMI video is preferred, but both your source device and your video display must have this type of video capability. If either device does not, then use component video, S-video or composite video.

Referring to Table 2, we recommend that you connect the DVD source to the Component Video 1 inputs, and any one source designated as Video 1, Video 2 or Video 3 to the Component Video 2 inputs. Any HDMI-capable source devices should be connected to one of the two HDMI inputs. All other source devices should be connected to either the S- or composite video input for that source. However, you may make whatever video connections are best for your system.

20

20

Image 20
Contents AVR Safety Information Outdoor Antenna Grounding. If an outside antennaImportant Safety Information Staple Invoice Here Table of Contents Introduction Thank you for choosing Harman KardonAudio Section Surround ModesSupplied Accessories Audio InputsAudio/Video Inputs With S-Video Digital Audio InputsFRONT-PANEL Controls Input Indicators REAR-PANEL Connections Video Component FM Antenna InputsOutputs Input VideoBridge/DMP Controls an iPod docked in The Bridge Remote Control FunctionsChannel Input Selector Press this button to select Power On AVR SelectorRemote Control Functions Introduction to Home Theater Surround ModesTypical Home Theater System Multichannel AudioConnecting Source Devices to the AVR ConnectionsSpeaker Connections SubwooferAudio Connections Digital AudioVideo Connections Analog AudioFM antenna uses a 75-ohm F-connector. See Figure AntennasAnalog Video Is colored red. See FigureSpeaker Placement Installation Step One Connect the SpeakersStep Two Connect the Subwoofer Step Three Connect the AntennasDevice Type Audio Connections Video ConnectionsTiVo or other Or Video 1 Composite Video Input Coax digital output Component video connections at allVideo 3 Source Video 1 SourceVideo 2 Source Step Five Connect the Video Display Hdmi 1 SourceHdmi 2 Source No video connections are neededStep Six Plug in AC Power Step Seven Insert Batteries in RemoteTurn on your source device Enter a code from aboveVideo Cable, Satellite Cable/SatelliteStep Nine Turn On the AVR Two steps are required the first time you turn on the AVRStep One Determine Speaker Size Initial SetupUsing the On-Screen Menu System Speaker Size Menu Step Three Manual Setup MenuStep Two Measure Speaker Distances Is not present, such as when a DVD is paused Speaker Crossover MenuSee Figure Delay Adjust MenuStep Four Output Level Calibration Using the Remote Control With Source Material Using the Full-OSD MenuStep Five Configure Sources Tuner at this timeInput Setup Menu Screen for DMP/The Bridge source Sleep Timer Volume ControlOperation Turning On the AVRHeadphones Mute FunctionTone Controls Source SelectionWhen you wish to view a DVD, simply select the DVD source Audio Input SelectionVideo Input Selection Channel Direct InputsUsing the Tuner Channel Input SelectorUsing TheBridgeTM RecordingSelecting a Surround Mode Select a Surround Mode RemoteAnalog Audio Signals Digital Audio SignalsAdvanced Functions Audio Processing and Surround SoundSurround Modes Provides descriptions of all surround modes available on Dolby Surround SettingsDefault Modes Panorama adjusts wraparound surround effect 0 orDolby Digital EX played as Passages to avoid disturbing othersSurround Mode Description Incoming Bitstream or Signal System Settings Advanced Remote Control FunctionsDim Function Punch-Through ProgrammingTo program punch-through control while operating any device Press the Power Off Button to program the Power Off commandTo program, or record a macro, follow these steps Memory Processor ResetResetting the Remote Troubleshooting Guide AVR 146 Technical Specifications DTSAppendix Default settings, worksheets, remote product codes Table A1 Source Input Setting DefaultsTable A2 Speaker/Channel Setting Defaults Table A3 Delay Setting DefaultsTable A4 Source Input Settings Table A5 Speaker/Channel SettingsTable A6 Remote Control Codes Table A7 System SettingsFeature Default Setting Your Setting Off Volume Default Default Vol Set 25dBTable A8 Remote Control Function List TV VID3Remote Control Function List Table A8Aiwa Table A9 Table A10Table A11 Remote Control Product Codes CD Table A12 Remote Control Product Codes DVDTable A14 Remote Control Product Codes Tape Table A15 Remote Control Product Codes CBLTable A16 Remote Control Product Codes Table A15
Related manuals
Manual 1 pages 4.96 Kb

AVR 146 specifications

The Harman-Kardon AVR 146 is a versatile audio-video receiver designed to elevate home entertainment experiences. A product of the renowned Harman-Kardon brand, this receiver combines advanced audio technologies, user-friendly features, and sleek design, making it a popular choice for audiophiles and casual listeners alike.

One of the standout characteristics of the AVR 146 is its power output. It delivers 50 watts per channel across seven channels, allowing it to easily drive a wide range of speakers while ensuring that dynamic soundscapes are reproduced with clarity and depth. This capability makes it suitable for both movies and music, enhancing the overall auditory experience in home theater setups.

The AVR 146 supports high-definition audio formats, including Dolby TrueHD and DTS-HD Master Audio. These formats provide lossless sound quality, allowing listeners to appreciate every nuance of their favorite films and albums. The receiver's support for a 7.1 channel layout enriches movie nights with a surround sound experience, drawing viewers deeper into the action.

Connectivity is another key feature of the AVR 146. It is equipped with multiple HDMI inputs, allowing users to connect several high-definition devices such as Blu-ray players, gaming consoles, and streaming devices. This ensures that users can enjoy high-quality audio and video without the need for constant plug-and-play. Additionally, the receiver features an array of analog and digital inputs, which further broaden its compatibility with various devices.

Setup and operation are simplified by the inclusion of the user-friendly on-screen graphical interface. This intuitive design makes it easy to navigate through the various settings and features, allowing users to customize their audio preferences with ease. The AVR 146 also incorporates the Harman Kardon Quick Select feature, which allows users to save their favorite settings for different sources for quick access.

In terms of design, the Harman-Kardon AVR 146 showcases a modern and elegant appearance synonymous with the brand's aesthetic. It features a sleek front panel with an easy-to-read display and well-organized buttons, blending seamlessly into home environments.

In summary, the Harman-Kardon AVR 146 is a well-rounded audio-video receiver that promises exceptional performance and versatility. With its combination of powerful amplification, support for advanced audio formats, extensive connectivity options, and a user-friendly interface, it is an excellent choice for anyone looking to enhance their home entertainment system. Whether for movie enthusiasts or music lovers, the AVR 146 delivers an auditory experience that impresses and satisfies.