Harman-Kardon AVR 146 owner manual Step Nine Turn On the AVR

Page 26

INSTALLATION

Step Nine – Turn On the AVR 146

Two steps are required the first time you turn on the AVR 146.

1.Gently press the Master Power Switch until the word OFF is no longer visible. The Power Indicator above the two power switches should light up in amber, indicating that the AVR is in Standby mode and is ready to be turned on. See Figure 34. Normally, you may leave the Master Power Switch in the ON position, even when the receiver is not being used.

Figure 34 – Power Switches

2.There are several ways in which the AVR 146 may be turned on from Standby mode.

a)Press the Standby/On Switch on the front panel. See Figure 34.

b)Press the Source Select Button on the front panel. See Figure 35.

Figure 35 – Source Select Button

c)Using the remote, press any one of these buttons: AVR, DVD/CD, TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2, VID3, AM/FM or 6CH. See Figure 36.

Figure 36 – AVR and Input Selectors

NOTE: Any time you press one of the Input Selectors on

the remote (i.e., DVD/CD, TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2 or VID3), the remote will switch modes so that it will only transmit the codes programmed to operate that device. In order to control the receiver, you will need to press the AVR button to return the remote to AVR mode.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents AVR Safety Information Outdoor Antenna Grounding. If an outside antennaImportant Safety Information Staple Invoice Here Table of Contents Audio Section IntroductionThank you for choosing Harman Kardon Surround ModesAudio/Video Inputs With S-Video Supplied AccessoriesAudio Inputs Digital Audio InputsFRONT-PANEL Controls Input Indicators REAR-PANEL Connections Outputs Input Video ComponentFM Antenna Inputs VideoBridge/DMP Controls an iPod docked in The Bridge Remote Control FunctionsChannel Input Selector Press this button to select Power On AVR SelectorRemote Control Functions Typical Home Theater System Introduction to Home TheaterSurround Modes Multichannel AudioSpeaker Connections Connecting Source Devices to the AVRConnections SubwooferVideo Connections Audio ConnectionsDigital Audio Analog AudioAnalog Video FM antenna uses a 75-ohm F-connector. See FigureAntennas Is colored red. See FigureSpeaker Placement Step Two Connect the Subwoofer InstallationStep One Connect the Speakers Step Three Connect the AntennasTiVo or other Or Video 1 Composite Video Input Device TypeAudio Connections Video Connections Coax digital output Component video connections at allVideo 3 Source Video 1 SourceVideo 2 Source Hdmi 2 Source Step Five Connect the Video DisplayHdmi 1 Source No video connections are neededStep Six Plug in AC Power Step Seven Insert Batteries in RemoteVideo Cable, Satellite Turn on your source deviceEnter a code from above Cable/SatelliteStep Nine Turn On the AVR Two steps are required the first time you turn on the AVRStep One Determine Speaker Size Initial SetupUsing the On-Screen Menu System Speaker Size Menu Step Three Manual Setup MenuStep Two Measure Speaker Distances Is not present, such as when a DVD is paused Speaker Crossover MenuSee Figure Delay Adjust MenuStep Four Output Level Calibration Using the Remote Control With Source Material Using the Full-OSD MenuStep Five Configure Sources Tuner at this timeInput Setup Menu Screen for DMP/The Bridge source Operation Sleep TimerVolume Control Turning On the AVRTone Controls HeadphonesMute Function Source SelectionVideo Input Selection When you wish to view a DVD, simply select the DVD sourceAudio Input Selection Channel Direct InputsUsing the Tuner Channel Input SelectorUsing TheBridgeTM RecordingSelecting a Surround Mode Select a Surround Mode RemoteAdvanced Functions Analog Audio SignalsDigital Audio Signals Audio Processing and Surround SoundSurround Modes Provides descriptions of all surround modes available on Dolby Surround SettingsDefault Modes Dolby Digital EX played as Panorama adjusts wraparound surround effect0 or Passages to avoid disturbing othersSurround Mode Description Incoming Bitstream or Signal Dim Function System SettingsAdvanced Remote Control Functions Punch-Through ProgrammingTo program punch-through control while operating any device Press the Power Off Button to program the Power Off commandTo program, or record a macro, follow these steps Memory Processor ResetResetting the Remote Troubleshooting Guide AVR 146 Technical Specifications DTSTable A2 Speaker/Channel Setting Defaults Appendix Default settings, worksheets, remote product codesTable A1 Source Input Setting Defaults Table A3 Delay Setting DefaultsTable A4 Source Input Settings Table A5 Speaker/Channel SettingsFeature Default Setting Your Setting Table A6 Remote Control CodesTable A7 System Settings Off Volume Default Default Vol Set 25dBTable A8 Remote Control Function List TV VID3Remote Control Function List Table A8Aiwa Table A9 Table A10Table A11 Remote Control Product Codes CD Table A12 Remote Control Product Codes DVDTable A14 Remote Control Product Codes Tape Table A15 Remote Control Product Codes CBLTable A16 Remote Control Product Codes Table A15
Related manuals
Manual 1 pages 4.96 Kb

AVR 146 specifications

The Harman-Kardon AVR 146 is a versatile audio-video receiver designed to elevate home entertainment experiences. A product of the renowned Harman-Kardon brand, this receiver combines advanced audio technologies, user-friendly features, and sleek design, making it a popular choice for audiophiles and casual listeners alike.

One of the standout characteristics of the AVR 146 is its power output. It delivers 50 watts per channel across seven channels, allowing it to easily drive a wide range of speakers while ensuring that dynamic soundscapes are reproduced with clarity and depth. This capability makes it suitable for both movies and music, enhancing the overall auditory experience in home theater setups.

The AVR 146 supports high-definition audio formats, including Dolby TrueHD and DTS-HD Master Audio. These formats provide lossless sound quality, allowing listeners to appreciate every nuance of their favorite films and albums. The receiver's support for a 7.1 channel layout enriches movie nights with a surround sound experience, drawing viewers deeper into the action.

Connectivity is another key feature of the AVR 146. It is equipped with multiple HDMI inputs, allowing users to connect several high-definition devices such as Blu-ray players, gaming consoles, and streaming devices. This ensures that users can enjoy high-quality audio and video without the need for constant plug-and-play. Additionally, the receiver features an array of analog and digital inputs, which further broaden its compatibility with various devices.

Setup and operation are simplified by the inclusion of the user-friendly on-screen graphical interface. This intuitive design makes it easy to navigate through the various settings and features, allowing users to customize their audio preferences with ease. The AVR 146 also incorporates the Harman Kardon Quick Select feature, which allows users to save their favorite settings for different sources for quick access.

In terms of design, the Harman-Kardon AVR 146 showcases a modern and elegant appearance synonymous with the brand's aesthetic. It features a sleek front panel with an easy-to-read display and well-organized buttons, blending seamlessly into home environments.

In summary, the Harman-Kardon AVR 146 is a well-rounded audio-video receiver that promises exceptional performance and versatility. With its combination of powerful amplification, support for advanced audio formats, extensive connectivity options, and a user-friendly interface, it is an excellent choice for anyone looking to enhance their home entertainment system. Whether for movie enthusiasts or music lovers, the AVR 146 delivers an auditory experience that impresses and satisfies.
Top Page Image Contents