Harman-Kardon AVR 146 Speaker Crossover Menu, Is not present, such as when a DVD is paused

Page 29

LEFT/RIGHT: This line tells the AVR 146 the capabilities of your front left and right speakers. Use the /Buttons to select either SMALL or LARGE for these speakers.

CENTER: Move the cursor to the line for the center speaker, and use the /Buttons to select a setting for this speaker.

NOTE: If the receiver is currently in one of the Logic 7 surround modes, which will be the case the first time you turn on the receiver, you won’t be able to set the center speaker to LARGE, due to the requirements of the Logic 7 processor. You may use the SMALL setting instead. As you listen to the receiver, if you find the SMALL setting is not satisfactory, change the surround mode to one of the Dolby Pro Logic II modes (using the Surround Select menu, accessible from the Master Menu), and then you may come back to this menu and change the center speaker to the LARGE setting.

SURROUND: Move the cursor to the line for the surround, or rear, speakers, and use the /Buttons to select a setting for these two speakers.

SUBWOOFER: Move the cursor to the line for the subwoofer, which is programmed a little differently. The subwoofer’s “size” setting depends upon how you programmed the front left and right speakers.

If you set the front speakers to SMALL, the subwoofer setting will be SUB, and you won’t be able to change it. All low-frequency information will always be sent to the subwoofer. If you don’t have a subwoofer, you may wish to set your front speakers to LARGE so as not to lose this information, but you may need to lower the volume to avoid adverse results. We recommend that you either upgrade to full-range speakers or add a subwoofer to your system at the earliest opportunity.

If you set the front speakers to LARGE, you may select from three possible settings for the subwoofer.

L/R+LFE: This setting sends all low-frequency information to the subwoofer, including both information that would normally be played through the front left and right speakers and the special low-frequency effects (LFE) channel information.

LFE: This setting plays low-frequency information contained in the left and right program channels to the front speakers, and directs only the LFE channel information to the subwoofer.

NONE: This setting steers all low-frequency information to the front speakers, and no information to the subwoofer output. Use this setting if you have a passive subwoofer, or a powered subwoofer that you connected to the front speaker outputs.

NOTE: If you are using a Harman Kardon HKTS speaker system, select the SMALL setting for the LEFT/RIGHT, CENTER and SURROUND lines, and the subwoofer will automatically be set to SUB.

INITIAL SETUP

BASS MGR: This advanced setting is used if you wish to configure your speakers differently for different sources. For example, you may prefer to set your speakers to LARGE while listening to CDs from your CD player. By changing this setting to INDEPENDENT, you may have different settings for your CD player and your DVD player or other devices. We recommend that you leave this setting at its factory default of GLOBAL until you have more experience with the AVR.

Move the cursor to the BACK TO MANUAL SETUP line and press the Set Button to return to the Manual Setup Menu.

The speaker sizes may also be configured without using the on-screen menu system. Press the Speaker Setup Button on the remote, and use the /¤ Buttons to select the desired speaker group (Front Speakers, Center Speaker, Surround Speakers, Subwoofer). Press the Set Button to display the current setting for the speaker group, and use the /¤ Buttons again to change the setting. Press the Set Button to return to the previous display, or wait a few seconds for the AVR to return to normal operation on its own.

NOTE: The Speaker/Channel Indicators on the front panel of the receiver (see Figure 41) will display the speaker size settings as follows. For each speaker configured as SMALL, a single box will appear in the position for that speaker. For each speaker configured as LARGE, a double box will appear in its position. If a speaker is configured as NONE, no box will appear. The subwoofer will be indicated by a single box, or no box if no subwoofer has been configured. The letters inside the boxes appear when a digital signal is being received that has that channel discretely encoded. The letters flash when the signal

is not present, such as when a DVD is paused.

Figure 41 – Speaker/Channel Input Indicators

Speaker Crossover Menu

On the Manual Setup menu, move the cursor to the SPEAKER X-OVER line and press the Set Button to display the Speaker Crossover menu. See Figure 42.

Figure 42 – Speaker Crossover Menu Screen

29

Image 29
Contents AVR Outdoor Antenna Grounding. If an outside antenna Safety InformationImportant Safety Information Staple Invoice Here Table of Contents Thank you for choosing Harman Kardon IntroductionAudio Section Surround ModesAudio Inputs Supplied AccessoriesAudio/Video Inputs With S-Video Digital Audio InputsFRONT-PANEL Controls Input Indicators REAR-PANEL Connections FM Antenna Inputs Video ComponentOutputs Input VideoBridge/DMP Controls an iPod docked in The Bridge Remote Control FunctionsChannel Input Selector Press this button to select AVR Selector Power OnRemote Control Functions Surround Modes Introduction to Home TheaterTypical Home Theater System Multichannel AudioConnections Connecting Source Devices to the AVRSpeaker Connections SubwooferDigital Audio Audio ConnectionsVideo Connections Analog AudioAntennas FM antenna uses a 75-ohm F-connector. See FigureAnalog Video Is colored red. See FigureSpeaker Placement Step One Connect the Speakers InstallationStep Two Connect the Subwoofer Step Three Connect the AntennasAudio Connections Video Connections Device TypeTiVo or other Or Video 1 Composite Video Input Coax digital output Component video connections at allVideo 3 Source Video 1 SourceVideo 2 Source Hdmi 1 Source Step Five Connect the Video DisplayHdmi 2 Source No video connections are neededStep Seven Insert Batteries in Remote Step Six Plug in AC PowerEnter a code from above Turn on your source deviceVideo Cable, Satellite Cable/SatelliteTwo steps are required the first time you turn on the AVR Step Nine Turn On the AVRStep One Determine Speaker Size Initial SetupUsing the On-Screen Menu System Speaker Size Menu Step Three Manual Setup MenuStep Two Measure Speaker Distances Speaker Crossover Menu Is not present, such as when a DVD is pausedSee Figure Delay Adjust MenuStep Four Output Level Calibration Using the Full-OSD Menu Using the Remote Control With Source MaterialTuner at this time Step Five Configure SourcesInput Setup Menu Screen for DMP/The Bridge source Volume Control Sleep TimerOperation Turning On the AVRMute Function HeadphonesTone Controls Source SelectionAudio Input Selection When you wish to view a DVD, simply select the DVD sourceVideo Input Selection Channel Direct InputsChannel Input Selector Using the TunerRecording Using TheBridgeTMSelect a Surround Mode Remote Selecting a Surround ModeDigital Audio Signals Analog Audio SignalsAdvanced Functions Audio Processing and Surround SoundSurround Modes Provides descriptions of all surround modes available on Dolby Surround SettingsDefault Modes 0 or Panorama adjusts wraparound surround effectDolby Digital EX played as Passages to avoid disturbing othersSurround Mode Description Incoming Bitstream or Signal Advanced Remote Control Functions System SettingsDim Function Punch-Through ProgrammingTo program punch-through control while operating any device Press the Power Off Button to program the Power Off commandTo program, or record a macro, follow these steps Memory Processor ResetResetting the Remote Troubleshooting Guide DTS AVR 146 Technical SpecificationsTable A1 Source Input Setting Defaults Appendix Default settings, worksheets, remote product codesTable A2 Speaker/Channel Setting Defaults Table A3 Delay Setting DefaultsTable A5 Speaker/Channel Settings Table A4 Source Input SettingsTable A7 System Settings Table A6 Remote Control CodesFeature Default Setting Your Setting Off Volume Default Default Vol Set 25dBTV VID3 Table A8 Remote Control Function ListTable A8 Remote Control Function ListAiwa Table A10 Table A9Table A12 Remote Control Product Codes DVD Table A11 Remote Control Product Codes CDTable A15 Remote Control Product Codes CBL Table A14 Remote Control Product Codes TapeTable A15 Table A16 Remote Control Product Codes
Related manuals
Manual 1 pages 4.96 Kb

AVR 146 specifications

The Harman-Kardon AVR 146 is a versatile audio-video receiver designed to elevate home entertainment experiences. A product of the renowned Harman-Kardon brand, this receiver combines advanced audio technologies, user-friendly features, and sleek design, making it a popular choice for audiophiles and casual listeners alike.

One of the standout characteristics of the AVR 146 is its power output. It delivers 50 watts per channel across seven channels, allowing it to easily drive a wide range of speakers while ensuring that dynamic soundscapes are reproduced with clarity and depth. This capability makes it suitable for both movies and music, enhancing the overall auditory experience in home theater setups.

The AVR 146 supports high-definition audio formats, including Dolby TrueHD and DTS-HD Master Audio. These formats provide lossless sound quality, allowing listeners to appreciate every nuance of their favorite films and albums. The receiver's support for a 7.1 channel layout enriches movie nights with a surround sound experience, drawing viewers deeper into the action.

Connectivity is another key feature of the AVR 146. It is equipped with multiple HDMI inputs, allowing users to connect several high-definition devices such as Blu-ray players, gaming consoles, and streaming devices. This ensures that users can enjoy high-quality audio and video without the need for constant plug-and-play. Additionally, the receiver features an array of analog and digital inputs, which further broaden its compatibility with various devices.

Setup and operation are simplified by the inclusion of the user-friendly on-screen graphical interface. This intuitive design makes it easy to navigate through the various settings and features, allowing users to customize their audio preferences with ease. The AVR 146 also incorporates the Harman Kardon Quick Select feature, which allows users to save their favorite settings for different sources for quick access.

In terms of design, the Harman-Kardon AVR 146 showcases a modern and elegant appearance synonymous with the brand's aesthetic. It features a sleek front panel with an easy-to-read display and well-organized buttons, blending seamlessly into home environments.

In summary, the Harman-Kardon AVR 146 is a well-rounded audio-video receiver that promises exceptional performance and versatility. With its combination of powerful amplification, support for advanced audio formats, extensive connectivity options, and a user-friendly interface, it is an excellent choice for anyone looking to enhance their home entertainment system. Whether for movie enthusiasts or music lovers, the AVR 146 delivers an auditory experience that impresses and satisfies.