Conair Water/Spray Tanks, UGE014/0999 manual HOW IT Works

Page 11

The extrusion enters the water or spray compartment after

HOW IT WORKS

leaving the calibration tooling or a sizing tank. Simple support

and hold-down rollers ar used to hold small diameter hollow

 

forms in position as the extrusion passes through the tank.

 

Contoured support and hold-down rollers usually are required

 

for large hollow forms.

 

In a WT water tank, the extrusion is submerged in a flooded

 

water compartment. Water enters the compartment through a

 

quick fill valve or through one center-supply, drilled water

 

header that is mounted along the top and back side of the

 

compartment. The water level is controlled by a telescoping

 

overflow standpipe.

 

In the ST spray tank, the extrusion may be submerged or

 

held above the water.

 

All water enters the compartment

 

through four center-supply water

 

headers mounted at the four

 

corners along the full length of the

 

compartment. These water headers

 

are drilled or equipped with spray

 

heads. Each pair of spray headers

 

has its own water supply valve.

 

Water levels are controlled by the

 

setting of the standpipe. When set

 

low, the standpipe keeps the water

 

level below the extrusion. When set

 

high, the standpipe allows com-

 

plete submersion of the extrusion

 

in a flooded compartment.

 

The extrusion passes from the water or spray compartment

 

into an air-wipe compartment equipped with two, tubular air

 

wiper rings connected to compressed air. Angled holes drilled

 

in the wiper ring blasts air on the extrusion in the direction of

 

the extruder to blow off surface water. A gasket seal at the

 

exit of the air wipe compartment ensures the extrusion will be

 

dry as it reaches the puller.

 

UGE014/0999

Water/Spray Tanks

DESCRIPTION 2-3

Image 11
Contents Page Date Manual Number UGE014/0999 Serial numbers Model numbers Introduction Table of ContentsPage Introduction Your Responsibility AS a User Purpose User GuideHOW Guide is Organized Read this SO no ONE Gets Hurt Page Description TANK? What isHOW IT Works Tank Style SpecificationsOptions FeaturesFeatures and Options CON Closed Water Recirculation System Option Features and Options CON Installation Unpacking the Boxes Make sure the installation area provides Preparing for InstallationPosition the tank downstream of the extruder Aligning the TankConnecting Main Power Connecting a Chiller Connecting Water AIR SuppliesTesting the Installation Page Operation Make sure the extruder and puller are ready Determine the cooling mode you will usePreparing for OperationThread the extrudate through the tank Preparing for OperationStart the other equipment in the extrusion line StartingStopping Maintenance Weekly, or as often as needed Preventative Maintenance ScheduleLubricating Tank Components Cleaning Tank Spray BarsReplacing Gaskets Checking Electrical Connections Open the electrical enclosure. a safety deviceInspect the wires and connections. Look for Inspect the exterior power cords. CarefullyTroubleshooting FEW Words Before BeginningPossible cause Solution Product Quality ProblemsPage From outside the United States, call WE’RE Here to HelpWarranty Limitations Equipment Guarantee Performance Warranty

Water/Spray Tanks, UGE014/0999 specifications

The Conair UGE014/0999 is a highly efficient water and spray tank system designed for various industrial applications, particularly in the realm of plastics processing and manufacturing. This solution stands out for its advanced features, robust construction, and user-friendly operation, making it a valuable asset for any plant seeking to enhance productivity and ensure the quality of its output.

One of the primary features of the Conair UGE014/0999 is its sizable tank capacity. Designed to hold substantial volumes of water, it enables continuous operation without the need for frequent refilling. This characteristic is especially advantageous in processes that require sustained cooling or moisture application, such as in cooling hot molds or maintaining optimal conditions for plastic products.

In terms of technologies, the Conair UGE014/0999 incorporates state-of-the-art pumping and spraying mechanisms that provide reliable and consistent performance. The system is outfitted with precision-engineered pumps capable of delivering uniform spray patterns, ensuring that the application of water is even and effective. This enhances the quality of the finished products while minimizing waste.

Another significant characteristic of the UGE014/0999 is its robust construction. Made from high-quality materials, this water and spray tank is designed to withstand the rigors of industrial environments. Its corrosion-resistant design not only extends its lifespan but also requires less maintenance, making it a cost-effective solution for manufacturers.

The ease of operation is another highlight of the Conair UGE014/0999. The tank is designed with user-friendly controls, allowing operators to easily adjust settings according to specific processing requirements. This flexibility ensures that the system can be tailored to meet the demands of varying production scenarios, thus increasing efficiency.

Furthermore, safety is a paramount consideration in the design of the Conair UGE014/0999. It features built-in safety mechanisms to prevent leaks and spills, protecting both the equipment and the working environment. This focus on safety is essential in any industrial setting, where the potential for accidents can have serious implications.

In conclusion, the Conair UGE014/0999 water and spray tank represents a perfect blend of advanced technology, robust construction, and user-friendly design. With its large capacity, efficient spraying capabilities, and safety features, it stands as a reliable choice for industries needing effective moisture management in their processes, ultimately contributing to enhanced production quality and efficiency.