Conair UGE014/0999 manual Starting, Stopping, Start the other equipment in the extrusion line

Page 28

STARTING THE

WT/ST TANK

1 Turn water pump on, if you have the optional recirculation system.

After the tank has been filled, press REC START button.

2 Start the other equipment in the extrusion line.

3 Gradually increase line speed. Raise extruder rpms slowly until extrudate is close to the product desired.

4 Wet tank rim lightly and close lid. Dip fingers into tank water and wet the tank rim to improve the seal.

5 Adjust water flow and water levels. The best water flow rates and levels depend upon your material, process and cooling mode.

NOTE: You should check profile size and surface finish at start up and periodically throughout pro- cessing. Check the size of the profile using an optional in-line laser gauge, ID or OD gauge. Check the surface finish for imperfections. See the TROUBLESHOOTING section for product quality prob- lems that could be related to the WT/ST tank.

STOPPING THE

WT/ST TANK

Tank operation is stopped by turning off the water pump. Extrudate will continue to move through the tank unless the entire extrusion line is shut down. A typical shutdown proce- dure is given below.

1 Move the tank downstream. While the material is still running, turn the large handwheel to move the tank away from the die.

2

3

4

5

6

Lower extruder rpms.

Cut the plastic off at the die with a soft metal spatula or scraper.

Cover the tank entrance hole. Place one hand over the hole to limit water spillage when you stop the pump.

Turn the water pump off. Press REC STOP.

Drain the tank and reservoirs if the tank will not be used ore requires water system mainte- nance.

4-4

OPERATION

Water/Spray Tanks

UGE014/0999

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Page Date Manual Number UGE014/0999 Serial numbers Model numbers Table of Contents IntroductionPage Introduction HOW Guide is Organized Purpose User GuideYour Responsibility AS a User Read this SO no ONE Gets Hurt Page Description What is TANK?HOW IT Works Specifications Tank StyleFeatures OptionsFeatures and Options CON Closed Water Recirculation System Option Features and Options CON Installation Unpacking the Boxes Preparing for Installation Make sure the installation area providesAligning the Tank Position the tank downstream of the extruderConnecting Main Power Connecting Water AIR Supplies Connecting a ChillerTesting the Installation Page Operation Determine the cooling mode you will use Preparing forOperation Make sure the extruder and puller are readyPreparing for Operation Thread the extrudate through the tankStopping StartingStart the other equipment in the extrusion line Maintenance Preventative Maintenance Schedule Weekly, or as often as neededReplacing Gaskets Cleaning Tank Spray BarsLubricating Tank Components Open the electrical enclosure. a safety device Inspect the wires and connections. Look forInspect the exterior power cords. Carefully Checking Electrical ConnectionsTroubleshooting Before Beginning FEW WordsProduct Quality Problems Possible cause SolutionPage WE’RE Here to Help From outside the United States, callEquipment Guarantee Performance Warranty Warranty Limitations

Water/Spray Tanks, UGE014/0999 specifications

The Conair UGE014/0999 is a highly efficient water and spray tank system designed for various industrial applications, particularly in the realm of plastics processing and manufacturing. This solution stands out for its advanced features, robust construction, and user-friendly operation, making it a valuable asset for any plant seeking to enhance productivity and ensure the quality of its output.

One of the primary features of the Conair UGE014/0999 is its sizable tank capacity. Designed to hold substantial volumes of water, it enables continuous operation without the need for frequent refilling. This characteristic is especially advantageous in processes that require sustained cooling or moisture application, such as in cooling hot molds or maintaining optimal conditions for plastic products.

In terms of technologies, the Conair UGE014/0999 incorporates state-of-the-art pumping and spraying mechanisms that provide reliable and consistent performance. The system is outfitted with precision-engineered pumps capable of delivering uniform spray patterns, ensuring that the application of water is even and effective. This enhances the quality of the finished products while minimizing waste.

Another significant characteristic of the UGE014/0999 is its robust construction. Made from high-quality materials, this water and spray tank is designed to withstand the rigors of industrial environments. Its corrosion-resistant design not only extends its lifespan but also requires less maintenance, making it a cost-effective solution for manufacturers.

The ease of operation is another highlight of the Conair UGE014/0999. The tank is designed with user-friendly controls, allowing operators to easily adjust settings according to specific processing requirements. This flexibility ensures that the system can be tailored to meet the demands of varying production scenarios, thus increasing efficiency.

Furthermore, safety is a paramount consideration in the design of the Conair UGE014/0999. It features built-in safety mechanisms to prevent leaks and spills, protecting both the equipment and the working environment. This focus on safety is essential in any industrial setting, where the potential for accidents can have serious implications.

In conclusion, the Conair UGE014/0999 water and spray tank represents a perfect blend of advanced technology, robust construction, and user-friendly design. With its large capacity, efficient spraying capabilities, and safety features, it stands as a reliable choice for industries needing effective moisture management in their processes, ultimately contributing to enhanced production quality and efficiency.
Top Page Image Contents