Conair Water/Spray Tanks Replacing Gaskets, Lubricating Tank Components, Cleaning Tank Spray Bars

Page 31

To replace an end gasket:

1 Remove the retaining rings. Loosen the wing nuts and lift off the ring that holds the gasket in place.

2 Remove the damaged gasket and slide a new gasket over the studs. No sealant is required.

3 Reassemble. Slip the retaining ring over the studs to cover the gasket. Tighten the wing nuts.

REPLACING GASKETS

Normal operation of the WT/ST tank creates many wet sur- faces. We recommend generous monthly lubrication of any threaded or sliding components involved in positioning the tank. Those components include the positioning mechanisms such as the up/down vertical support shafts, side-to-side cross thread, and the linear actuator. You may need to lubricate more often than monthly.

1 Lubricate the vertical support shaft and grease fittings. Apply bearing compound to the fit- tings until it overflows. Apply a coating of the compound to the shafts as well.

2 Lubricate the side-to-side cross thread grease fittings. Apply bearing compound to the fittings until it overflows. Apply a coating of the compound to the thread as well.

LUBRICATING

THE TANK

COMPONENTS

Tools required:

❒grease gun

❒seize-resistant bearing compound

3

Lubricate the linear actuator according to manufacturer’s instructions.

The tank, spray bars and optional recirculation reservoir should be thoroughly to remove particles that can accumulate.

1

Drain the tank and reservoir.

 

 

2

Wipe surfaces thoroughly to remove particles.

3 Remove the spray bars. Twist each spray bar coun- terclockwise and pull it out.

4 Clean the spray bars. Flush each bar with a compressed air line or water hose. Use a soft brush to remove any particles clogging the small holes.

CLEANING THE

TANK AND

SPRAY BARS

5

Reassemble by repeating the steps in reverse order.

UGE014/0999

Water/Spray Tanks

MAINTENANCE 5-3

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Page Date Manual Number UGE014/0999 Serial numbers Model numbers Introduction Table of ContentsPage Introduction HOW Guide is Organized Purpose User GuideYour Responsibility AS a User Read this SO no ONE Gets Hurt Page Description TANK? What isHOW IT Works Tank Style SpecificationsOptions FeaturesFeatures and Options CON Closed Water Recirculation System Option Features and Options CON Installation Unpacking the Boxes Make sure the installation area provides Preparing for InstallationPosition the tank downstream of the extruder Aligning the TankConnecting Main Power Connecting a Chiller Connecting Water AIR SuppliesTesting the Installation Page Operation Make sure the extruder and puller are ready Determine the cooling mode you will usePreparing for OperationThread the extrudate through the tank Preparing for OperationStopping StartingStart the other equipment in the extrusion line Maintenance Weekly, or as often as needed Preventative Maintenance ScheduleReplacing Gaskets Cleaning Tank Spray BarsLubricating Tank Components Checking Electrical Connections Open the electrical enclosure. a safety deviceInspect the wires and connections. Look for Inspect the exterior power cords. CarefullyTroubleshooting FEW Words Before BeginningPossible cause Solution Product Quality ProblemsPage From outside the United States, call WE’RE Here to HelpWarranty Limitations Equipment Guarantee Performance Warranty

Water/Spray Tanks, UGE014/0999 specifications

The Conair UGE014/0999 is a highly efficient water and spray tank system designed for various industrial applications, particularly in the realm of plastics processing and manufacturing. This solution stands out for its advanced features, robust construction, and user-friendly operation, making it a valuable asset for any plant seeking to enhance productivity and ensure the quality of its output.

One of the primary features of the Conair UGE014/0999 is its sizable tank capacity. Designed to hold substantial volumes of water, it enables continuous operation without the need for frequent refilling. This characteristic is especially advantageous in processes that require sustained cooling or moisture application, such as in cooling hot molds or maintaining optimal conditions for plastic products.

In terms of technologies, the Conair UGE014/0999 incorporates state-of-the-art pumping and spraying mechanisms that provide reliable and consistent performance. The system is outfitted with precision-engineered pumps capable of delivering uniform spray patterns, ensuring that the application of water is even and effective. This enhances the quality of the finished products while minimizing waste.

Another significant characteristic of the UGE014/0999 is its robust construction. Made from high-quality materials, this water and spray tank is designed to withstand the rigors of industrial environments. Its corrosion-resistant design not only extends its lifespan but also requires less maintenance, making it a cost-effective solution for manufacturers.

The ease of operation is another highlight of the Conair UGE014/0999. The tank is designed with user-friendly controls, allowing operators to easily adjust settings according to specific processing requirements. This flexibility ensures that the system can be tailored to meet the demands of varying production scenarios, thus increasing efficiency.

Furthermore, safety is a paramount consideration in the design of the Conair UGE014/0999. It features built-in safety mechanisms to prevent leaks and spills, protecting both the equipment and the working environment. This focus on safety is essential in any industrial setting, where the potential for accidents can have serious implications.

In conclusion, the Conair UGE014/0999 water and spray tank represents a perfect blend of advanced technology, robust construction, and user-friendly design. With its large capacity, efficient spraying capabilities, and safety features, it stands as a reliable choice for industries needing effective moisture management in their processes, ultimately contributing to enhanced production quality and efficiency.
Top Page Image Contents