Main Remote Control Functions

E ‹ Button: This button is used to change the menu selection or setting during some of the setup procedures for the AVR.

FSet Button: This button is used to enter settings into the AVR’s memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjust- ment.

GDigital Select: Press this button to assign one of the digital inputs *Ó to a source. (See page 41 for more information on using digital inputs.)

HNumeric Keys: These buttons serve as a ten-button numeric keypad to enter tuner preset positions. They are also used to select channel numbers when TV, VCR or Sat receiver has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed.

ITuner Mode: Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so MANUAL appears in the Main Information Display Ò, pressing the Tuning buttons K) will move the frequency up or down in single-step increments. When the FM band is in use and AUTO appears in the Main Information Display Ò, pressing this button will change to monaural reception making even week stations audible. (See page 51 for more information.)

JDirect Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button simply press the proper Numeric Keys H to select a station (See page 51 for more information on the tuner).

KTuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the Tuner Mode button I has been pressed or the Band but- ton ! on the front panel was held pressed so that AUTO appears in the Main Information Display Ò, pressing either of the buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the MANUAL appears in the Main Information Display Ò, pressing these buttons will tune stations in single-step increments. (See page 51 for more information.)

LOSD Button: Press this button to activate the On Screen Display (OSD) system used to set up or adjust the AVR’s parameters.

MDolby Mode Selector: This button is used to select one of the available Dolby Surround processing modes. Each press of this button will select one of the Dolby Pro Logic II modes, Dolby 3 Stereo or Dolby Digital. Note that the Dolby Digital mode is only available with a digital input selected and the other modes only as long as a Dolby Digital source is not playing (except Pro Logic II with Dolby Digital 2.0 recordings, see page 37-38). See page 37 for the available Dolby surround mode options.

NDTS Digital Mode Selector: When a DTS source is in use the AVR will select the appropri- ate mode automatically and no other mode will be available. Pressing this button will display the mode currently selected by the AVR´s decoder, depending on the surround material played and the speaker setting. When a DTS source is not in use, this button has no function. (See page 37 for the available DTS options.)

OLogic 7 Selector: Press this button to select one of the available Logic 7 surround modes. (See page 37-38 for the available Logic 7 options.)

PTransport Control Buttons: These but- tons do not have any functions for the AVR, but they may be programmed for the forward/reverse play operation of a wide variety of CD or DVD players, and audio or video- cas- sette recorders. (See page 53 for more informa- tion on programming the remote.)

QMulti-Room:Press this button to activate the Multiroom system or to begin the process of changing the input or volume level for the sec- ond zone. (See page 47 for more information on the Multiroom system.)

Skip Up/Down Buttons: These buttons do not have a direct function with the AVR, but when used with a compatibly programmed CD or DVD player/changer they will change the tracks on the disc currently being played.

Stereo Mode Selector: Press this button to select a stereo playback mode. When the but- ton is pressed so that SURROUNDOFF appears in the Main Information Display Ò, with only the Surr Off Surround Mode Indicator ( lit, the AVR will operate in a bypass mode with true fully analog, two-channel left/right stereo mode with no surround process- ing or bass management as opposed to other modes where digital processing is used. When the button is pressed so that SURROUND OFF appears in the Main Information Display Ò, with both the DSP and Surr Off Surround Mode Indicators ( lit, you may enjoy a two-channel presentation of the sound along with the benefits of bass management. When the button is pressed so that 5 CH STEREO or 7 CH STEREO appears, the stereo signal is routed to all five speakers, if installed. (See page 28 for more information on stereo playback modes).

DTS Neo:6 Mode Selector: Pressing this selector button cycles the AVR through the various DTS Neo:6 modes, which extract a five-, six- or seven-channel surround field from two-channel program material (from PCM source or analog input signal). The first press selects the last DTS Neo:6 surround mode that was in use, and each subsequent press selects the next mode.

Macro Buttons: Press these buttons to store or recall a “Macro”, which is a pre-pro- grammed sequence of commands stored in the remote. (See page 55 for more information on storing and recalling macros).

RDS Select Button: Press this button to display the various messages that are part of the RDS data system of the AVR’s tuner. (See page 52 for more information on RDS).

Preset Up/Down: When the tuner is in use, press these buttons to scroll through the stations programmed into the AVR’s memory. When CD or DVD is selected using the Input Selector button 4, these buttons may function as Slow Fwd/Rev (DVD) or ”+10” (CD, CDR).

Clear Button: Press this button to clear incorrect entries when using the remote to directly enter a radio station’s frequency.

ENGLISH

MAIN REMOTE CONTROL FUNCTIONS 13