Harman-Kardon 347 System Configuration, First Turn On, Using the On-Screen Display, System Setup

Page 23

System Configuration

Subwoofers produce largely nondirectional sound, so they may be placed almost anywhere in a room. Actual placement should be based on room size and shape and the type of subwoofer used. One method of finding the optimal location for a subwoofer is to begin by placing it in the front of the room, about 15cm from a wall, or near the front corner of the room. Another method is to temporarily place the subwoofer in the spot where you will normally sit, and then walk around the room until you find a spot where the subwoofer sounds best. Place the subwoofer in that spot. You should also follow the instructions of the subwoofer’s manufacturer, or you may wish to experiment with the best location for a subwoofer in your listening room.

Once the speakers have been placed in the room and connected, the remaining steps are to pro- gram the system configuration memories.

Although it is necessary to assign input/output settings and surround mode choices manually, we recommend that you take advantage of the power and precision of EzSet/EQ to automatical- ly select and enter the settings for all other audio parameters. This will not only save you time; it will ensure that your room is calibrated and equalized with an accuracy not possible when these settings are made manually. You are now ready to power up the AVR 347 to begin these final adjustments.

First Turn On

You are now ready to power up the AVR to begin these final adjustments.

1.Plug the Power Cable ￿ into an un- switched AC outlet.

2.Press the Main Power Switch 1 in until it latches and the word “OFF” on the top of the switch disappears inside the front panel. Note that the Power Indicator 3 will turn orange, indicating that the unit is in the Standby mode.

3.Remove the protective plastic film from the main front-panel lens. If left in place, the film may affect the performance of your remote control.

4.Install the three supplied AAA batteries in the remote as shown. Be certain to follow the (+) and (–) polarity indicators that are on the top of the battery compartment.

5.Turn the AVR on either by pressing the System Power Control 2 or the Input Source Selector % on the front panel, or via the remote by pressing the Power On Button 3, AVR Selector 5or any of the Input Selectors 46on the remote. The Power Indicator 3 will turn blue to confirm that the unit is on, and the Main Information Display Ò will also light up.

NOTE: After pressing one of the Input Selector buttons 4 to turn the unit on, press the AVR Selector 5 to have the remote control the AVR functions.

Using the On-Screen Display

When making the following adjustments, you may find them easier to make via the unit’s on- screen display system. These easy-to-read displays give you a clear picture of the current status of the unit and facilitate speaker, delay, input or digital selection you are making.

To view the on-screen displays, make certain you have made a connection from either the HDMI Output # or the Video Monitor Out jack ￿ on the rear panel to the HDMI, component, com- posite or S-Video input of your TV or projector. In order to view the AVR’s displays, the correct video input must be selected on your video dis- play.

IMPORTANT NOTE: When viewing the on-screen menus using a CRT-based projector, plasma display or any direct-view CRT monitor or television, it is important that they not be left on the screen for an extended period of time. As with any video dis- play, but particularly with projectors, constant dis- play of a static image such as these menus or video game images may cause the image to be permanently “burned into” the CRT. This type of damage is not covered by the AVR warranty and may not be covered by the projector TV set’s war- ranty.

The AVR has two on-screen display modes, “Semi-OSD” and “Full-OSD.” When making con- figuration adjustments, it is recommended that the Full-OSD mode be used. This will place a complete status report or option listing on the screen, making it easier to view the available options and make the settings on the screen. The Semi-OSD mode uses one-line displays only.

Note that when the full OSD system is in use, the menu selections are not shown in the Infor- mation Display Ò. When the full OSD menu system is used, OSD ON will appear in the Main Information Display Ò to remind you that a video display must be used.

When the semi-OSD system is used in conjunc- tion with the discrete configuration buttons, the on screen display will show a single line of text with the current menu selection. That selection will also be shown in the Main Information

Display Ò.

The full OSD system can always be turned on or off by pressing the OSD button L. When this button is pressed the MASTER MENU (Figure 1) will appear, and adjustments are made from the individual menus. Note that the menus will remain on the screen for 20 seconds after the latest action was made on the screen menu, then they will “time-out” and disappear from the screen. The time-out may be increased to as much as 50 seconds by going to the SYSTEM SETUP menu, and changing the item titled FULL OSD TIME OUT.

The semi-OSD system is also available as a sys- tem default, although it may be turned off by using the SYSTEM SETUP menu. (See page 49). With the semi-OSD system, you may make adjustments directly, by pressing the buttons on the front panel or remote control for the specific parameter to be adjusted. For example, to change the digital input for any of the sources, press the Digital Select Button ÛG and then any of the Selector buttons ‹ / › 7 or ⁄/¤ D on the front panel or remote.

System Setup

The AVR 347 features an advanced memory system that enables you to establish different configurations for, digital input, surround mode, for each input source. This flexibility enables you to custom tailor the way in which you listen to each source and have the AVR memorize them. This means, for example, that you may associate different surround modes and analog or digital inputs with different sources. Once these settings are made, they will automatically be recalled whenever you select that input.

However, we recommend that the first time you use the AVR, you take advantage of the simplici- ty of configuring the system using the EzSet/EQ process, which takes the guesswork out of speaker size and delay settings, and balances the speaker output levels to tailor the AVR’s sound presentation to your specific system and room. Before beginning the EzSet/EQ procedure, there are a few adjustments that need to be made to ensure accurate results.

ENGLISH

SYSTEM CONFIGURATION 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents AVR 347 Audio/ Video Receiver Declaration of Conformity Table of ContentsIntroduction Description and FeaturesImportant Safety Information Safety InformationDo not place the unit directly on a carpeted surface Installation LocationCleaning UnpackingFront Panel Controls Headphone Jack $ Speaker/Channel Input IndicatorDigital Input Selector When playing a # Preset Stations Selector Press thisSee page 44 for more information on the Channel Indicators Rear Panel Connections Digital Audio Outputs Connect these Rear Panel Connections Main Remote Control Functions See page 46 for more information Main Remote Control Functions Main Remote Control Functions Changers Zone II.2 Remote Control FunctionsChange the input Zone II.2 Remote Control Functions Hdmi Input Connections Installation and ConnectionsAudio Equipment Connections Hdmi ConnectionsWith the AVR 347 turned off, connect Video Equipment ConnectionsVideo Video In/Out jacks, if it´s a recording VCR Scart A/V ConnectionsVideo Connection Notes Important Note for the Use SCART-Cinch Adapters Important Note for Adapter CablesImportant Notes for S-Video connections TV, see item belowAC Power Connections System and Power ConnectionsMain Room Remote Control Extension BUS Installation ConnectionsSpeaker Selection Speaker PlacementFirst Turn On System ConfigurationUsing the On-Screen Display System SetupInput Setup Video Optical Source InputCoax Surround Setup Night Mode Settings Stereo-Digital Mode Configuring the Surround Off Stereo ModesAutomated Speaker Setup Using EzSet/EQ Stereo-Direct Bypass ModeNavigation Buttons E to highlight System Configuration Speaker Size Setup Manual SetupCenter System Configuration Delay Settings Output Level Adjustment Main menu appears on the screen Up the Volume until you can hear the test noise clearlyWhen all channels have the same output level Is then pressed to select OFF in the highlighted videoOperation Surround Mode ChartMain speakers and a subwoofer Dolby 3 StereoReference WideVideo Input Selection Using the Sleep TimerBasic Operation Source SelectionChannel/8-Channel Direct Input Controls and Use of HeadphonesSurround Mode Selection Volume Up/Down ButtonsSelecting a Digital Source Digital Audio PlaybackDolby Digital PCM Audio PlaybackIncoming Bitstream Available Surround Modes Surround Mode TypesDigital Bitstream Indicators PCM Playback Indications Incoming Signal Available Surround ModesSee Figure Speaker/Channel IndicatorsNight Mode Menu Button UsingTape Recording Pressing the DMP Selector ButtonYou may then navigate the menus as explained above Output Level Adjustment With Source SignalsMemory Backup Normal output level adjustment forSurround Amplifier Channel Assignment Multiroom OperationMultiroom Remote room Or mute the output GFront-Panel-Display Fade Video AdjustmentsVideo Adjustments Advanced FeaturesFull-OSD Time Out Adjustment Advanced FeaturesTurn On Volume Level Semi-OSD SettingsBasic Tuner Operation Default Surround ModeRDS Display Options RDS TuningTuner Operation RDS OperationDirect Code Entry Programming the RemoteProgramming the Remote with Codes Code ReadoutPress the Input Selector 45 button Learning Codes from a RemoteErasing Learned Codes VID1/VCR VID3/TV VID2/CBL/SATPress the AVR Selector Erasing Macro CommandsMacro Programming Programmed Device FunctionsTransport Control Punch-Through Volume Punch-ThroughChannel Control Punch-Through Resetting the Remote Memory DVD Function ListAVR DVD Remote sensor Ú is obscured Troubleshooting GuideProcessor Reset Power Switch 1 is pushedTechnical Specifications Center Speaker Size VideoTable A4 Source Input Settings Harman Consumer Group, Inc

347 specifications

The Harman-Kardon 347 is a notable piece of audio equipment that combines advanced technological features with a user-friendly design to deliver high-quality sound. As a receiver, the Harman-Kardon 347 is engineered to cater to audiophiles who seek both performance and aesthetics in their home audio systems.

One of the standout features of the Harman-Kardon 347 is its powerful amplification capabilities. The receiver boasts a multi-channel design that allows it to deliver robust audio output, making it suitable for both music and home theater setups. Users can enjoy a well-balanced sound profile that ensures clarity across all frequencies, providing an immersive listening experience.

In terms of connectivity, the Harman-Kardon 347 is equipped with a plethora of input options. It supports various audio formats and allows for seamless integration with different devices, whether it be a CD player, Blu-ray player, or streaming device. The receiver includes multiple HDMI inputs, enabling high-definition video and audio transmission, which is essential for modern entertainment systems.

Another notable aspect of the Harman-Kardon 347 is its implementation of advanced audio technologies. It features Dolby Digital and DTS support, ensuring that users can experience surround sound as intended by content creators. This feature enhances the experience of watching movies or playing video games, allowing for a deeply immersive soundstage.

Moreover, the Harman-Kardon 347 has been designed with ease of use in mind. Its intuitive interface and remote control allow users to navigate through settings and inputs with minimal effort. The clear and organized layout makes it accessible for individuals who may not be as tech-savvy, ensuring that everyone can enjoy high-quality audio without a steep learning curve.

The build quality of the Harman-Kardon 347 also deserves mention. With its sleek and modern design, this receiver can seamlessly blend into any home decor. The attention to detail in its construction not only adds aesthetic appeal but also ensures durability, allowing users to enjoy this device for many years without concern.

In summary, the Harman-Kardon 347 stands out in the crowded market of audio receivers. With its robust amplification, multiple connectivity options, advanced audio technologies, user-friendly interface, and stylish design, it offers a comprehensive audio solution for both casual listeners and serious audiophiles alike. Whether for music enjoyment or enhancing the home theater experience, the Harman-Kardon 347 is well-equipped to meet and exceed expectations.
Top Page Image Contents