Harman-Kardon 347 Basic Operation, Source Selection, Video Input Selection, Using the Sleep Timer

Page 39

Operation

Basic Operation

Once you have completed the setup and configu- ration of the AVR, it is simple to operate and enjoy. The following instructions should be followed for you to maximize your enjoyment of your new receiver:

Turning the AVR On or Off

•When using the AVR for the first time, you must press the Main Power Switch 1 on the front panel to turn the unit on. This places the unit in a Standby mode, as indicated by the amber color of the Power Indicator 3. Once the unit is in Standby, you may begin a listening session by pressing the System Power Control 2 or the Source button % on the front panel or the AVR Selector 5. Note that the Power Indicator 3 will turn blue. This will turn the unit on and return it to the input source that was last used. The unit may also be turned on from Standby by pressing any of the Source Selector buttons on the remote 4567CD I or the Source button % on the front panel.

NOTE: After pressing one of the Input Selector buttons 4 (except VID3) to turn the unit on, press the AVR Selector 5 to have the remote control the AVR functions.

To turn the unit off at the end of a listening ses- sion, simply press the System Power Control

2on the front panel or the Power Off Button 3A on the remote. Power will be shut off to any equipment plugged into the rear panel Switched AC Outlets ￿ and the Power Indicator 3 will turn orange.

When the remote is used to turn the unit “off” it is actually placing the system in a Standby mode, as indicated by the orange color of the Power Indicator 3.

When you will be away from home for an extended period of time it is always a good idea to completely turn the unit off with the front panel Main Power Switch 1.

NOTE: All preset memories may be lost if the unit is left turned off with the Main Power Switch 1 for more than two weeks.

Using the Sleep Timer

•To program the AVR for automatic turn-off, press the Sleep Button 9 on the remote. Each press of the button will increase the time before shut down in the following sequence:

The sleep time will be displayed in the Main Information Display Ò and it will count down until the time has elapsed.

When the programmed sleep time has elapsed, the unit will automatically turn off (to Standby mode). Note that the front panel display will dim to one half brightness when the Sleep function is programmed. To cancel the Sleep function, press and hold the Sleep Button 9 until the information display returns to normal brightness and the Sleep indicator numbers disappear and the words SLEEP OFF appear in the Main Information Display Ò.

Source Selection

For direct access to any source, press its Input Selector 467 CDI on the remote. Since the AVR 347 allows for more source input devices than the remote has buttons for, some sources are required to share buttons. These are the DVD and CD sources, the Tape and The Bridge sources, and the HDMI 1 and HDMI 2 sources. The first press of any of these three Input Selectors will select the source whose name appears on the button, i.e., DVD, Tape or HDMI 1. Press that Input Selector again to select the source whose name appears above the button (i.e., CD, The Bridge or HDMI 2), and the LED on the remote will light in green to indicate that you have selected the source whose name is printed in green above the button. Each additional press toggles between the two sources.

NOTE: After pressing one of the Input Selector buttons 4 to turn the unit on, press the

AVR Selector 5 to have the remote control the AVR functions.

•The input source may also be changed by pressing the front-panel Input Source Selector button %. Each press of the button will move the input selection through the list of available inputs.

•The front-panelVideo 4 Inputs Ô, Optical Digital 4 Input * or the Coaxial Digital 4 Input Ó may be used to connect a device such as a video game or camcorder to your home entertainment system on a temporary basis.

•As the input source is changed, the new input name will appear momentarily as an on-screen display in the lower third of the video display.

The input name will also appear in the Main Information Display Ò and a blue LED will light next to the selected input’s name in the front-panelInput Indicators .

•When Digital Media Player (DMP) source is selected, if a compatible Apple iPod device is inserted in an optional Harman Kardon that is connected to DMP Connector ￿ on the rear panel, function mes- sages will appear on any video display connect- ed to the AVR’s Video Monitor Outputs ￿, and the remote control may be used to navigate the iPod and access many of its functions. The function messages will also appear in the front- panel display, and the iPod’s battery may be charged. See the owner’s guides for and your iPod for more information.

Video Input Selection

When a source is selected, the AVR switches to a video input as follows:

The Video In line of the Input Setup menu indicates which of the component video inputs on the AVR is assigned to each source. By default the Component Video 1 input is assigned to the DVD source, the Component Video 2 input is assigned to the Video 1 source, and the Component Video 3 input is assigned to the Video 2 source.

The two HDMI inputs obtain the video signal from their own inputs, and may not be reassigned to another video input.

If your iPod is capable of playing still-images and videos, it may be used as a video source. However, you may reassign the video input for The Bridge to another device for viewing while listening to audio files stored on the iPod.

All other sources default to the Composite setting, meaning that they may only be used with their composite or S-video inputs. The AVR will transcode the incoming composite or S-video signal and make it available using the HDMI or component video monitor outputs, enabling a single-cable connection to your television.

The component video inputs may be reassigned to other source inputs as needed, depending on the physical connections you made during the Installation procedure.

If a signal is present at the component video input assigned to that source, it will be selected.

If no signal is present at the component video input, then the S-video or composite video input for the source will be selected. It is not possible to reassign the S-video or composite video inputs to other sources.

For audio-only sources, such as the tuner or CD inputs, when no component video signal is present, the last-used video source will be selected.

ENGLISH

OPERATION 39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents AVR 347 Audio/ Video Receiver Declaration of Conformity Table of ContentsIntroduction Description and FeaturesImportant Safety Information Safety InformationDo not place the unit directly on a carpeted surface Installation LocationCleaning UnpackingFront Panel Controls Headphone Jack $ Speaker/Channel Input Indicator# Preset Stations Selector Press this See page 44 for more information on the Channel IndicatorsDigital Input Selector When playing a Rear Panel Connections Digital Audio Outputs Connect these Rear Panel Connections Main Remote Control Functions See page 46 for more information Main Remote Control Functions Main Remote Control Functions Zone II.2 Remote Control Functions Change the inputChangers Zone II.2 Remote Control Functions Hdmi Input Connections Installation and ConnectionsAudio Equipment Connections Hdmi ConnectionsWith the AVR 347 turned off, connect Video Equipment ConnectionsScart A/V Connections Video Connection NotesVideo Video In/Out jacks, if it´s a recording VCR Important Note for the Use SCART-Cinch Adapters Important Note for Adapter CablesImportant Notes for S-Video connections TV, see item belowAC Power Connections System and Power ConnectionsMain Room Remote Control Extension BUS Installation ConnectionsSpeaker Selection Speaker PlacementFirst Turn On System ConfigurationUsing the On-Screen Display System SetupInput Setup Source Input CoaxVideo Optical Surround Setup Night Mode Settings Stereo-Digital Mode Configuring the Surround Off Stereo ModesAutomated Speaker Setup Using EzSet/EQ Stereo-Direct Bypass ModeNavigation Buttons E to highlight System Configuration Speaker Size Setup Manual SetupCenter System Configuration Delay Settings Output Level Adjustment Main menu appears on the screen Up the Volume until you can hear the test noise clearly When all channels have the same output level Is then pressed to select OFF in the highlighted videoOperation Surround Mode ChartMain speakers and a subwoofer Dolby 3 StereoReference WideVideo Input Selection Using the Sleep TimerBasic Operation Source SelectionChannel/8-Channel Direct Input Controls and Use of HeadphonesSurround Mode Selection Volume Up/Down ButtonsSelecting a Digital Source Digital Audio PlaybackDolby Digital PCM Audio PlaybackSurround Mode Types Digital Bitstream IndicatorsIncoming Bitstream Available Surround Modes PCM Playback Indications Incoming Signal Available Surround ModesSpeaker/Channel Indicators Night ModeSee Figure Menu Button UsingTape Recording Pressing the DMP Selector ButtonYou may then navigate the menus as explained above Output Level Adjustment With Source SignalsMemory Backup Normal output level adjustment forMultiroom Operation MultiroomSurround Amplifier Channel Assignment Remote room Or mute the output GFront-Panel-Display Fade Video AdjustmentsVideo Adjustments Advanced FeaturesFull-OSD Time Out Adjustment Advanced FeaturesTurn On Volume Level Semi-OSD SettingsBasic Tuner Operation Default Surround ModeRDS Display Options RDS TuningTuner Operation RDS OperationDirect Code Entry Programming the RemoteProgramming the Remote with Codes Code ReadoutPress the Input Selector 45 button Learning Codes from a RemoteErasing Learned Codes VID1/VCR VID3/TV VID2/CBL/SATPress the AVR Selector Erasing Macro CommandsMacro Programming Programmed Device FunctionsVolume Punch-Through Channel Control Punch-ThroughTransport Control Punch-Through Resetting the Remote Memory DVD Function ListAVR DVD Remote sensor Ú is obscured Troubleshooting GuideProcessor Reset Power Switch 1 is pushedTechnical Specifications Center Speaker Size VideoTable A4 Source Input Settings Harman Consumer Group, Inc
Top Page Image Contents