Operation
After a period of time the screen may disappear from view. The length of time is set using the
E, and you may then navigate the menus as explained above.
NOTE: It is strongly recommended that you use a screen saver built into your video display to avoid possible damage from
Output Level Adjustment
With Source Signals
Normal output level adjustment for the
AVR is established using the test tone, as out- lined on page 35. In some cases, however, it may be desirable to adjust the output levels using program material such as a test disc, or a selec- tion you are familiar with. Additionally, the out- put level for the subwoofer and those for the Stereo modes can only be adjusted using this procedure.
To adjust the output levels using program mate- rial, first select the surround mode for which you want to trim the speakers (see NOTE below),
start your program material source and set the |
|
reference volume for the front left and front |
|
right channels using the Volume Control | . |
Once the reference level has been set, press the Channel Select button CÙ and note that FRONT L LEVEL will appear in the Main Information Display Ò. To change the level, first press the Set button F@, and then use the Selector buttons 7 or the ⁄/ ¤ buttons
Dto raise or lower the level. DO NOT use the volume control, as this will alter the reference setting.
Once the change has been made, press the Set button F@ and then press the Selector buttons 7 or the ⁄/¤ buttons D to select the next output channel location that you wish to adjust. To adjust the subwoofer level, press the Selector buttons 7 or the ⁄/¤ buttons
Duntil WOOFER LEVEL appears in the Main Information Display Ò or
Press the Set button F@ when the name of the desired channel appears in the Main Information Display Ò and
Repeat the procedure as needed until all chan- nels requiring adjustment have been set. When all adjustments have been made and no further adjustments are made for five seconds, the AVR will return to normal operation.
The channel output may also be adjusted using the
Dto scroll to the Ch Adjust line and press the Set Button F to display the Ch Adjust submenu.
Figure 29
When the menu appears, the internal test tone will be turned off. This will allow you to use your external test disc or other source material as the test signal. Press the Set Button F and use the ⁄/¤ Buttons D to select the channels to be adjusted. At each channel position press the Set Button F followed by the ‹ / › Buttons E to change the output level. Remember, when you are using a disc with test signal (e.g. pink noise) or an external signal generator as the source, the goal is to have the output level at each channel be equal when heard at the listening position, with any sur- round mode selected. When your test source is a normal disc with music signals, you may adjust the level for each channel and surround mode as you prefer, e.g. you may lower the center chan- nel level when you find it to be too high or increase the level of the rears when you find it to be too low with specific surround modes.
If you wish to reset all the levels to their original factory default of 0dB offset, press the ⁄/¤ Buttons D so that the blue cursor bar is highlighting the RESET line and press the Set Button F. After the levels are reset, resume the procedure outlined above to reset the levels to the desired settings. When all adjustments are done, press the ‹ Button E consecutive times to move back to the main menu to make other adjustments. If you have no other adjust- ments to make, press the OSD Button L to exit the menu system.
NOTE: The output levels may be separately trimmed for each digital and analog surround mode. If you wish to have different trim levels for a specific mode, select that mode and then follow the instructions in the steps shown above.
With Stereo modes the adjustment procedure described above is the only way to trim the out- put level, e.g. to match the Stereo level with other modes.
Dim Function
Since the AVR will often be used when movies or other video programming is viewed under low- light conditions, you may wish to lower the brightness of the
Simply press the Dim Button once to dim the front panel to half the normal brightness level; press it again to turn the displays off. Note that when the displays are dimmed or turned off, the blue lighting above the Standby/On Switch
2will continue to stay lit as a reminder that the AVR is still turned on.
Note that all changes to the
Dim Button as needed until the displays are on.
In addition to lowering the brightness of the dis- plays or turning them off completely, you may wish to have them appear whenever a button on the remote or front panel is pushed, and then gradually fade out after a set time period. You may do this by making the appropriate settings in the VFD Fade Timeout line of the SYSTEM SETUP menu, as shown on page 49.
Memory Backup
This product is equipped with a memory backup system that preserves tuner presets and system configuration information if the unit is turned off completely, accidentally unplugged or subjected to a power outage. This memory will last for approximately two weeks, after which time all information must be reentered.
46OPERATION