Bose 901 Series VI Hardware needed for ceiling suspension, General notes on ceiling suspension

Page 8

Figure 3

Mounting guidelines

Setting Up

Hardware needed for ceiling suspension

Screw hooks support the chains at the ceiling. They must have at least a #10 wood thread

with a shank diameter of at least 316 inch (4.5 mm). They should be long enough to go through any plasterboard and still have at least one inch (25 mm) of thread left to pene- trate a wood beam. For a masonry ceiling: use only high-quality metal expansion masonry anchors that fit the thread of the ceiling hooks.

Chain: diameter should be at least 532 inch (0.135 in. or 4 mm).

Screw eyes with S hooks attach chains to the speaker and must have at least a #10 wood thread with a shank diameter of at least 316 inch (4.5 mm) or larger.

All hardware (screw hooks, chain, screw eyes, S hooks) must have a manufacturer’s safe- load rating of 40 lb (18 kg) or more.

General notes on ceiling suspension

Suspend the speakers 18 – 36 inches (45 – 91 cm) from the ceiling; do not mount them flush to the ceiling.

To ensure an accurate stereo image, the distance from the floor should be three to ten feet (1 – 3.5 m). Be sure the speakers are no less than 18 inches (45 cm) from the floor. Do not suspend the speakers exactly halfway between the floor and ceiling.

Note: If the speakers are more than 10 feet (3 m) from the floor, we suggest you lengthen the chain supporting the rear of the speaker. By doing this you will allow the rear of the speaker, housing eight of the nine drivers, to be angled slightly downward.

Step by step procedure for ceiling suspension

1.Ceiling: Anchor at least two screw hooks into a rigid structural ceiling support (beam, joist,

or masonry anchor). Drill pilot holes into wood using a 18 inch drill bit (3.7 mm), if neces- sary.

2.Speaker: Use the three pre-drilled pilot holes (see Figure 2 - hole set B) on the bottom of

each speaker. Use a 18 inch drill bit (3.7 mm) to enlarge the pilot holes to accept the #10 thread screw eyes. Drill to a depth of 12 inch (12 mm) in the speaker cabinet. Do not drill completely through the cabinet.

Note: Contact Bose® for more information on suspending speakers. See the inside back cover for phone numbers. For details on your specific ceiling construction, consult a qualified building contractor or professional installer.

18 – 36” (45 – 91 cm)

4 – 12’

18 – 48”

(1.2 – 3.6 m)

(45 – 120 cm)

 

8 – 18”

– (20 – 45 cm)

4 – 12’

18 – 48”

(45 – 120 cm)

(1.2 – 3.6 m)

 

18 – 36” (45 – 91 cm)

 

English

Image 8
Contents Page Bose 901 Series VI Direct/Reflecting Please read this owner’s guide Additional safety informationFor your records Customer service Where to find…Warranty period Before you begin Unpacking the cartonsInstallation steps System CompatibilityChoosing the location for your speakers Choose the support for your speakersGeneral notes on ceiling suspension Step by step procedure for ceiling suspensionHardware needed for ceiling suspension Choosing the wire Preparing the speaker wiresConnecting the speakers Speaker connectionsStereo/non-home theater use Equalizer ConnectionsChecking the speaker connections Home theater use Home theater receiver connections Testing the speakers and equalizer To test the Tape Monitor connectionTo test the equalizer To test the PRE AMP OUT/MAIN AMP in connectionUsing other equipment To add a tape deck or VCRPlaying your speakers When connected to Tape MonitorWhen connected to PRE AMP OUT/MAIN AMP Using the Bass control Adjusting the soundUsing the MID-TREBLE and MID-BASS sliders Connecting additional speakers Equalizer compatibilityAdding 901 speakers Adding conventional speakersProblem What to do Cleaning your speakersTroubleshooting Accessories Technical informationCanada European OfficeAustralia Belgique/BelgiëPage Bose 901 Series VI Direct/Reflecting Veuillez lire la présente notice d’utilisation Pour vos dossiersAutres consignes de sécurité Période de garantie Service clientOù trouver… Avant de commencer Ouverture du carton d’emballageMarche à suivre pour l’installation Compatibilité du systèmeChoix d’un support pour les enceintes Disposition des enceintesInstructions pour la disposition Marche à suivre pour suspendre les enceintes Accessoires requis pour suspendre les enceintesRemarques générales pour suspendre les enceintes Connexion des enceintes Câbles appropriésPréparation des câbles Connexion des enceintesUtilisation Stéréo/non home theater connexions Tape Monitor Connexion de l’égaliseurVérification des connexions des enceintes Utilisation home theater Connexions PRE AMP OUT/MAIN AMP Tape MonitorConnexion d’un récepteur de Home Cinema Vérification d’une connexion PRE AMP OUT/MAIN AMP Vérification des enceintes et de l’égaliseurVérification d’une connexion magnétophone Tape Monitor Utilisation d’autres équipements Ajout d’un magnétophone ou magnétoscopeConnexion à la prise PRE AMP OUT/MAIN AMP Écoute des enceintesConnexion à la prise Tape Monitor Réglage des curseurs MID-TREBLE et MID-BASS Utilisation de la commande des BassesRéglage du son Compatibilité de l’égaliseur Connexion d’enceintes supplémentairesEnceintes 901 supplémentaires Enceintes conventionnelles supplémentairesDépannage Problème SolutionNettoyage des enceintes Accessoires Informations techniquesUSA