Wolf ICBWWD30 installation instructions Install Front Panel, Install Warming Drawer

Page 17

I N S TA L L AT I O N I N S T RU C T I O N S

S TA I N L E S S S T E E L FRONT PANEL

INSTALL FRONT PANEL

Remove all packaging materials from the handle and front panel. Gently remove the protective covering from the stainless steel front panel. The adhesive covering should peel away from the surface cleanly, but any remain- ing residue should be cleaned off with a mild detergent.

To attach the handle to the front panel, line up holes in the standoffs and handle with holes on the front panel. Insert handle screws through the holes in the front panel and tighten screws to the front panel.

Slide the top lip of the front panel over the drawer front. Insert three screws in the top of the front panel lip through the drawer front assembly and tighten screws. Insert three screws in the bottom of the front panel through the drawer front assembly and tighten screws. Refer to the illustration below.

Turn power off to the electrical outlet.

INSTALL WARMING DRAWER

Slide the left corner of the warming drawer into the opening. If the electrical outlet is installed inside the opening, plug the power cord into the outlet. The excess cord should be coiled behind or beside the unit. If the outlet is located in an adjacent cabinet, thread the power cord through the hole in the cabinet wall. Push the drawer back into the opening until the trim meets the cabinet front. Make sure the power cord does not get trapped under the warming drawer.

IMPORTANT NOTE: Do not lift up on the handle to push the drawer into place. Doing so could scratch the control panel.

Open the warming drawer to its full extension. Drill pilot holes in each side hole, located toward the front on each side of the warming drawer. Install the wood screws provided with the unit. Refer to the illustration below.

Turn power back on to the electrical outlet.

Attach handle

Warming drawer installation

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Warming Drawer Page G L I S H P Ã N O L A N Ç a I S TA L I a N O U T S C H N TAC T F O R M AT I O N S TA L L AT I O N R E Q U I R E M E N T S Wolf WA R M I N G D R AW E RWolf WA R M I N G D R AW E R F O R E YOU Start AccessoriesAW E R F R on T Options To O LS and M AT E R I a LS RequiredModel ICBWWD30 Installation SpecificationsUndercounter Installation Installation with BUILT- in Oven Optional Installations Wolf WA R M I N G D R AW E R T E G R AT E D Drawer Front Inset Application Overlay ApplicationInstallation with Built-In Oven Integrated Drawer Front Installation Options Wolf WA R M I N G D R AW E R E C T R I C a L Requirements Important NotePA C K the Warming Drawer Install Warming Drawer Trim Install Anti TIP BlockingInstall Warming Drawer Install Front PanelWolf WA R M I N G D R AW E R T E G R AT E D Front Panel Install Cleats and PlatformInstall Anti TIP Blocking Install Front Panel to Drawer N TAC T F O R M AT I O N F O R M AC I Ó N DE Contacto Referencia del modelo ICBWWD30 Número de serie R R a M I E N TA S Y M AT E R I a L E S J Ó N C a L E N TA D O R DE WolfOpciones DEL F R E N T E D E C a J Ó N OX I DA B L E Instrucciones DE I N S TA L a C I Ó NEspecificaciones DE LA Instalación Instalación Bajo EncimeraInstalación CON Horno Integrable Frente DE Cajón DE AC E R OInstalaciones Opcionales Modelo ICBWWD30 con frente de cajón integrado Aplicación Para Empotrar Aplicación RevestibleInstalación con horno integrable frente de cajón integrado Opciones DE Instalación Nota Importante Calentador Soportes DE LOS M U E B L E SS E M B a L a J E DEL Cajón Instalación DEL Borde DEL Cajón Calentador Panel Frontal DE AC E R OInstalación DEL Bloque Anti Vuelco Instalación DEL Cajón Calentador Instalación DEL Panel FrontalInstalación DE LOS Listones Y DE LA Plataforma Instalación DEL Bloque Anti Vuelco Instalación DEL Panel Frontal EN EL Cajón F O R M a Ción DE Contacto SI Necesita a S I S T E N C I a C N I C aF O R M AT I O N DE Contact ’ I N S TA L L AT I O N R O I R C H a U F F a N T WolfExigences Relatives R O I R C H a U F F a N T WO L F AccessoiresAVA N T DE Commencer Choix DE FAC a D E D E T I R O I RInstallation Sous Plan DE Travail Specifications D’INSTALLATIONFacade DE Tiroir E N AC I E R OX Y DA B L EInstallation Avec Four Encastre Options D’INSTALLATION Dimensions hors-tout façade de tiroir intégrée Facade DE Tiroir I N T E G R E E S T RU C T I O N S D ’ I N S TA L L AT I O NHabillable Avec Panneau D’AFFLEUREMENTR O I R C H AU F FA N T WO L F Options D’INSTALLATION Remarque Importante Configuration E L E C T R I Q U EBA L LAG E DU Tiroir Chauffant R O I R C H AU F FA N T Wolf Installation DU Systeme AntibasculementInstallation DE LA Moulure DU Tiroir Chauffant Installation DU Tiroir Chauffant Installation DE LA FacadeFacade DE Tiroir I N T É G R É E Installation DES Tasseaux ET DE LA Plate FormeInstallation DU Systeme Antibasculement Installation DE LA Facade SUR LE Tiroir RV I C E Apres Vente F O R M a Z I O N PER I Contatti Numero del modello ICBWWD30 Numero di matricola ATT R E Z Z I E M AT E R I a L E Richiesti AccessoriZ I O N I M a S C H E R I NA T E R I O R E Installazione Sotto IL Piano DI Lavoro Specifiche PER L’INSTALLAZIONET RU Z I O N I P E R L’ I N S TA L LA Z I on E ACC I a I O I N O S S I DA B I L EMascherina Anteriore Installazione CON Forno IncassatoS S E TTO S C a L DAV I VA N D E WO L F ACC I a I O I N O S S I DA B I L E Installazioni OpzionaliT E G R ATA S C H E R I N a a N T E R I O R E Installazione a Sovrappo SizioneInstallazione AD Inserto Installazione CON Forno Incassato Opzioni PER L’INSTALLAZIONE Nota Importante Scaldavivande S S E TTO S C a L DAV I VA N D E Wolf Installazione DEL Blocco AntiribaltamentoInstallazione Della Rifinitura DEL Cassetto Scaldavivande Installazione DEL Cassetto Scaldavivande Installazione DEL Pannello AnterioreT E G R ATO Installazione DI Tacchetti E PiattaformaPannello Anteriore Installazione del cassetto scaldavivande Installazione DEL Pannello Anteriore SUL Cassetto Informazioni PER I Contatti Vorsicht Modellnummer ICBWWD30 Seriennummer WÄ R M E S C H U B LA D E VO N WO L F Modell ICBWWD30 Technische Daten ZUR InstallationUnterthekeninstallation WÄ R M E S C H U B LA D E VON Wolf Installation MIT EinbaubackofenBackofenrohbauöffnung Optionale Installationen597 mm Voll Integrierte Ausführung VerkleidungsausführungInstallation mit Einbaubackofen Integrierte Schubladenfront 610 mm + 749 mm InstallationsoptionenWichtiger Hinweis S PA C K E N DER Wärmeschublade Einfassung DER Wärmeschublade Installieren Kippschutzblock InstallierenWärmeschublade Installieren Frontplatte InstallierenSchlagleisten UND Plattform Installieren Kippschutzblock Installieren Frontplatte AN Schublade Installieren S TA L L AT I O N S Anweisungen H L E R S U C H E Wolf APPLIANCE, INC

ICBWWD30 specifications

The Wolf ICBWWD30 is a state-of-the-art built-in coffee machine designed for coffee enthusiasts who crave the ultimate brewing experience in the comfort of their own homes. With its sleek design and advanced technology, the ICBWWD30 combines functionality with aesthetics, making it a popular choice for modern kitchens.

One of the standout features of the Wolf ICBWWD30 is its ability to brew various coffee styles, including espresso, cappuccino, and lattes. Equipped with a powerful dual boiler system, it ensures that water is heated to the optimal temperature, allowing for precise extraction and rich flavor profiles. The machine's pre-infusion feature gently expands the coffee grounds before full brewing, enhancing the taste and aroma of each cup.

The ICBWWD30 also boasts a customizable user interface, allowing users to program their preferred coffee strength, temperature, and volume. This personalization ensures that every cup served is tailored to the individual's taste. Additionally, the machine includes a built-in grinder with multiple settings, providing freshly ground coffee beans for each brew. This feature not only enhances flavor but also allows users to select the grind size that best suits their brewing style.

Cleaning and maintenance are made easy with the Wolf ICBWWD30, as it incorporates a self-cleaning function. The removable brewing unit and milk container can be easily accessed and cleaned, ensuring that the integrity of the machine and the quality of coffee remain top-notch. Furthermore, the machine features a water filtration system that removes impurities, ensuring that every sip is pure and flavorful.

In terms of design, the ICBWWD30 seamlessly integrates into kitchen cabinetry, offering a built-in look that adds a touch of elegance to any space. Its simple yet sophisticated control panel features intuitive touch controls, making it easy for users to navigate through settings and options. The polished stainless steel finish is not only aesthetically pleasing but also ensures durability and resistance to corrosion.

Overall, the Wolf ICBWWD30 is a masterpiece in the realm of built-in coffee machines. With its combination of advanced brewing technologies, customizable settings, user-friendly design, and ease of maintenance, it is the perfect addition for anyone seeking to elevate their coffee experience at home. Whether you are a casual coffee drinker or a connoisseur, the ICBWWD30 promises to deliver the perfect cup every time.
Top Page Image Contents