Wolf W302210I E P 4 I N S TA L L R O U G H I N P L AT E, E P 5 I N S TA L L T H E H O O D

Page 15

I N S TA L L AT I O N I N S T R U C T I O N S

27" (686) DEEP WA L L H O O D S

If you are installing WBLOWER-90INT or WBLOWER-120INT, refer to the internal blower information on page 17 and follow installation instructions provided with the blower.

If you are installing an in-line or remote blower, drill a 7/8" (22) hole through the wood framing for the conduit. Refer to the in-line and remote blower information on pages 18–19 and follow installation instruc- tions provided with the blower.

IMPORTANT NOTE: Do not run wiring for the remote blower through the ductwork.

S T E P 4 : I N S TA L L R O U G H - I N P L AT E

Use the rough-in plate assembly to deter- mine the location of wall framing.

Install the #10 x 1" (25) screws (included with the hood) through the rough-in plate into the wall framing.

IMPORTANT NOTE: If additional support is required for the hood, drill supplementary mounting holes in the rough-in plate and use these holes to attach the hood assembly to the wall framing.

S T E P 5 : I N S TA L L T H E H O O D

IMPORTANT NOTE: If a backsplash is to be used, it should be installed before the wall hood is mounted.

Align both ends of the hood assembly with the ends of the rough-in plate. Refer to the illustration below.

Insert the back edges of the hood assembly into the rough-in plate and push the hood assembly toward the wall.

Place the studs on the rough-in plate into the slots on the hood. Use the hex head nuts (included with the hood) to secure the hood assembly to the rough-in plate.

Install the remaining #10 x 2" (51) screws (included with the hood) in the lower section of the hood. Verify that the screws engage the wall studs or framing. If not, wall anchors must be used.

Due to the weight of the hood, be sure to have adequate manpower for installation.

Soffit

Rough-In

Plate

Mounting

Holes

Hood installation

Dimensions in parentheses are in

 

millimeters unless otherwise specified.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Installation Instructions N TA C T F O R M AT I O N Wolf Customer Service Website Wolfappliance.comS T O F M AT E R I a L S S TA L L AT I O N R E Q U I R E M E N T SC T C O V E R Installation C O N S I D E R AT I O N SC E S S O R I E S E C T R I C a L R E Q U I R E M E N T SW- P R O F I L E WA L L H O O D S 6 1 0 D E E P WA L L H O O D S6 8 6 D E E P WA L L H O O D S Installation S P E C I F I C AT I O N S Low-Profile 24 610 Deep Wall Hoods27 686 Deep Wall Hoods Low-Profile Wall Hoods Model 24 610 Deep Wall Hoods Model27 686 Deep Wall Hoods Model E P 1 I N S TA L L D U C T W O R K To reduce the risk of fire, use only metal ductworkDucting options for low-profile wall hoods Ducting options for 24 610 deep wall hoods S TA L L AT I O N I N S T R U C T I O N SIf wall framing is not available, wall anchors must be used Rough-in plate/transition assemblyE P 2 WA L L P R E PA R AT I O N E P 3 H O O D P R E PA R AT I O NE P 4 R E AT TA C H R O U G H I N P L AT E Wall cut-out for low-profile hoods horizontal dischargeWall cut-out for 24 610 deep hoods horizontal discharge Hood installation E P 5 I N S TA L L T H E H O O DM P L E T E T H E I N S TA L L AT I O N 27 686 Deep WA L L H O O D S Mounting holes for 27 686 hoods Rough-in plate installationE P 4 I N S TA L L R O U G H I N P L AT E P O RTA N T N OT E PRO Wall V E N T I L AT I O N H O O D SE P 6 I N S TA L L W I R I N G T E R N a L B L O W E R I N S TA L L AT I O N Internal blower installationDimensions for BLOWER-60IL Dimensions for BLOWER-110IL Line a N D Remote B L O W E R SO W E R I N S TA L L AT I O N O W E R W I R I N G Dimensions for BLOWER-90REMDimensions for BLOWER-120REM Dimensions for BLOWER-150REMM OT E B L O W E R S Blower a S S E M B L I E ST E R N a L B L O W E R S L I N E B L O W E R SFilter and grease cup installation Duct cover installationYO U N E E D Service Nameplate I N S TA L L AT I O NRO U B L E S H O O T I N G Page 9 3 4 0 0
Top Page Image Contents