Wolf W302210I Line a N D Remote B L O W E R S, O W E R I N S Ta L L At I O N

Page 18

A C C E S S O R I E S

Optional acces- sories are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com.

W O L F PRO WALL VENTILATION H O O D S

IN - LINE A N D REMOTE B L O W E R S

B L O W E R I N S TA L L AT I O N

IMPORTANT NOTE: Refer to the specific installation instructions provided with each blower for additional mounting instructions.

Locate the blower so that the length of the duct run and number of elbows and transitions are kept to a minimum. Wolf recommends the maximum linear duct run be no greater than 50' (15 m).

If possible, remote blowers should be located between wall studs or roof rafters. Avoid pipes, wires or other ductwork that may be running through the wall.

Be sure that there is enough space for any transitions that may be needed between the blower and the connecting ductwork. For best performance, locate transitions nearest the blower.

Refer to the illustrations below and on the following page for overall dimensions of Wolf in-line and remote blowers. Also refer to the specific installation instructions provided with each remote blower to verify cut-out dimen- sions.

 

243/8"

 

(619)

113/4"

 

(298)

 

181/2"

 

(470)

 

 

41/2"

 

(114)

211/2"

121/4"

(546)

 

(311)

 

 

247/8"

 

 

(632)

18"

12"

 

(457)

 

 

(305)

 

 

 

8"

 

 

(203)

 

22"

18"

 

(559)

(457)

Dimensions for BLOWER-60IL

Dimensions for BLOWER-110IL

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Installation Instructions Wolf Customer Service Website Wolfappliance.com N TA C T F O R M AT I O NS TA L L AT I O N R E Q U I R E M E N T S S T O F M AT E R I a L SE C T R I C a L R E Q U I R E M E N T S Installation C O N S I D E R AT I O N SC E S S O R I E S C T C O V E RW- P R O F I L E WA L L H O O D S 6 1 0 D E E P WA L L H O O D S6 8 6 D E E P WA L L H O O D S Installation S P E C I F I C AT I O N S Low-Profile 24 610 Deep Wall Hoods27 686 Deep Wall Hoods Low-Profile Wall Hoods Model 24 610 Deep Wall Hoods Model27 686 Deep Wall Hoods Model E P 1 I N S TA L L D U C T W O R K To reduce the risk of fire, use only metal ductworkDucting options for low-profile wall hoods S TA L L AT I O N I N S T R U C T I O N S Ducting options for 24 610 deep wall hoodsE P 3 H O O D P R E PA R AT I O N Rough-in plate/transition assemblyE P 2 WA L L P R E PA R AT I O N If wall framing is not available, wall anchors must be usedE P 4 R E AT TA C H R O U G H I N P L AT E Wall cut-out for low-profile hoods horizontal dischargeWall cut-out for 24 610 deep hoods horizontal discharge Hood installation E P 5 I N S TA L L T H E H O O DM P L E T E T H E I N S TA L L AT I O N 27 686 Deep WA L L H O O D S Rough-in plate installation Mounting holes for 27 686 hoodsE P 4 I N S TA L L R O U G H I N P L AT E P O RTA N T N OT E PRO Wall V E N T I L AT I O N H O O D SE P 6 I N S TA L L W I R I N G Internal blower installation T E R N a L B L O W E R I N S TA L L AT I O NDimensions for BLOWER-60IL Dimensions for BLOWER-110IL Line a N D Remote B L O W E R SO W E R I N S TA L L AT I O N Dimensions for BLOWER-150REM Dimensions for BLOWER-90REMDimensions for BLOWER-120REM O W E R W I R I N GL I N E B L O W E R S Blower a S S E M B L I E ST E R N a L B L O W E R S M OT E B L O W E R SDuct cover installation Filter and grease cup installationYO U N E E D Service Nameplate I N S TA L L AT I O NRO U B L E S H O O T I N G Page 9 3 4 0 0
Top Page Image Contents