Wolf W302210I T E R N a L B L O W E R I N S TA L L AT I O N, Internal blower installation

Page 17

I N S TA L L AT I O N I N S T R U C T I O N S

I N T E R N A L B L O W E R S

IMPORTANT NOTE: Refer to the specific installation instructions provided with each internal blower for additional mounting and wiring instructions.

IMPORTANT NOTE: Use wire connectors or wire nuts approved by UL or C/UL.

IMPORTANT NOTE: Wolf recommends installing the internal blower to the rough-in plate assembly prior to installing the hood to the wall framing.

I N T E R N A L B L O W E R I N S TA L L AT I O N

Assemble the blower housing to the blower rough-in plate. Follow installation instruc- tions included with the blower assembly for proper installation.

Once the blower is mounted to the blower rough-in plate, attach the blower assembly to the hood rough-in plate. To attach, slide the blower rough-in plate over the weld studs and secure with eight nuts (included with the blower). Refer to the illustration below.

Verify that the blower discharge aligns with the discharge cut-out in the back panel of the hood.

Install the hood rough-in plate with blower assembly to the wall. Secure the power cord(s) without damaging or pinching while installing the hood shell.

For low-profile and 24" (610) wall hoods, follow hood installation instructions on page 8. For 27" (686) wall hoods, follow hood installation instructions on page 13.

Once the hood installation is complete, plug the blower power cord(s) into receptacle(s) located near the center of the hood shell. Use the clips on the interior of the hood to keep excess power cord away from moving parts.

IMPORTANT NOTE: Before turning the power on to the ventilation hood, make sure the blower is off.

Hood

Rough-In

Plate

Blower

Rough-In

Plate

Blower

Housing

Internal blower installation

Dimensions in parentheses are in

 

millimeters unless otherwise specified.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Installation Instructions N TA C T F O R M AT I O N Wolf Customer Service Website Wolfappliance.comS T O F M AT E R I a L S S TA L L AT I O N R E Q U I R E M E N T SC E S S O R I E S Installation C O N S I D E R AT I O N SE C T R I C a L R E Q U I R E M E N T S C T C O V E R6 8 6 D E E P WA L L H O O D S W- P R O F I L E WA L L H O O D S6 1 0 D E E P WA L L H O O D S 27 686 Deep Wall Hoods Installation S P E C I F I C AT I O N SLow-Profile 24 610 Deep Wall Hoods 27 686 Deep Wall Hoods Model Low-Profile Wall Hoods Model24 610 Deep Wall Hoods Model Ducting options for low-profile wall hoods E P 1 I N S TA L L D U C T W O R KTo reduce the risk of fire, use only metal ductwork Ducting options for 24 610 deep wall hoods S TA L L AT I O N I N S T R U C T I O N SE P 2 WA L L P R E PA R AT I O N Rough-in plate/transition assemblyE P 3 H O O D P R E PA R AT I O N If wall framing is not available, wall anchors must be usedWall cut-out for 24 610 deep hoods horizontal discharge E P 4 R E AT TA C H R O U G H I N P L AT EWall cut-out for low-profile hoods horizontal discharge M P L E T E T H E I N S TA L L AT I O N Hood installationE P 5 I N S TA L L T H E H O O D 27 686 Deep WA L L H O O D S Mounting holes for 27 686 hoods Rough-in plate installationE P 4 I N S TA L L R O U G H I N P L AT E E P 6 I N S TA L L W I R I N G P O RTA N T N OT EPRO Wall V E N T I L AT I O N H O O D S T E R N a L B L O W E R I N S TA L L AT I O N Internal blower installationO W E R I N S TA L L AT I O N Dimensions for BLOWER-60IL Dimensions for BLOWER-110ILLine a N D Remote B L O W E R S Dimensions for BLOWER-120REM Dimensions for BLOWER-90REMDimensions for BLOWER-150REM O W E R W I R I N GT E R N a L B L O W E R S Blower a S S E M B L I E SL I N E B L O W E R S M OT E B L O W E R SFilter and grease cup installation Duct cover installationRO U B L E S H O O T I N G YO U N E E D ServiceNameplate I N S TA L L AT I O N Page 9 3 4 0 0
Top Page Image Contents