Wolf W302210I S Ta L L At I O N R E Q U I R E M E N T S, S T O F M AT E R I a L S

Page 3

W O L F PRO WALL VENTILATION H O O D S

I N S TA L L AT I O N R E Q U I R E M E N T S

IMPORTANT NOTE: This installation must be completed by a qualified installer or Wolf authorized service center technician.

Installer: Please read the entire Installation Instructions prior to installation. Save these instructions for the local inspector’s refer- ence, then leave them with the homeowner.

Homeowner: Please read and keep these instructions for future reference and be sure to read the entire Use & Care Information prior to use.

Any questions or problems about the installation should be directed to your Wolf dealer or Wolf Appliance Company, Inc. at 800-332-9513. You can also visit our website at wolfappliance.com.

IMPORTANT NOTE: This appliance must be installed in accordance with National Electrical Codes, as well as all state, municipal and local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency, and amperage ratings are listed on the product rating plate.

Record the model and serial numbers before installing the Pro wall ventilation hood. Both numbers are listed on the rating plate, located on the left wall of the hood shell.

L I S T O F M AT E R I A L S

The following is a list of materials shipped with the Wolf Pro wall ventilation hood.

Stainless steel wall hood

Transition with backdraft damper (attached inside hood—needs to be removed)

Decorative stainless steel rail and installa- tion components—(R) model hoods only

Control knobs—two for low-profile and 24"

(610)deep hoods, three for 27" (686) deep hoods

Filters and grease cups (installed in hood)

(10) #10 x 2" (51) self-tapping hex head screws

(10) 10-24 washer nuts

Installation package (taped to filters)

Installation Instructions

Use & Care Information and product registration card

Wolf logo nameplate

Low-Profile Wall Hood

Low-Profile Wall Hood

(R) Rail Option

24" (610) Wall Hood

24" (610) Wall Hood

(R) Rail Option

27" (686) Wall Hood

Model Number

Serial Number

Dimensions in parentheses are in millimeters unless otherwise specified.

27" (686) Wall Hood

(R) Rail Option

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Installation Instructions N TA C T F O R M AT I O N Wolf Customer Service Website Wolfappliance.comS T O F M AT E R I a L S S TA L L AT I O N R E Q U I R E M E N T SC T C O V E R Installation C O N S I D E R AT I O N SC E S S O R I E S E C T R I C a L R E Q U I R E M E N T SW- P R O F I L E WA L L H O O D S 6 1 0 D E E P WA L L H O O D S6 8 6 D E E P WA L L H O O D S Installation S P E C I F I C AT I O N S Low-Profile 24 610 Deep Wall Hoods27 686 Deep Wall Hoods Low-Profile Wall Hoods Model 24 610 Deep Wall Hoods Model27 686 Deep Wall Hoods Model E P 1 I N S TA L L D U C T W O R K To reduce the risk of fire, use only metal ductworkDucting options for low-profile wall hoods Ducting options for 24 610 deep wall hoods S TA L L AT I O N I N S T R U C T I O N SIf wall framing is not available, wall anchors must be used Rough-in plate/transition assemblyE P 2 WA L L P R E PA R AT I O N E P 3 H O O D P R E PA R AT I O NE P 4 R E AT TA C H R O U G H I N P L AT E Wall cut-out for low-profile hoods horizontal dischargeWall cut-out for 24 610 deep hoods horizontal discharge Hood installation E P 5 I N S TA L L T H E H O O DM P L E T E T H E I N S TA L L AT I O N 27 686 Deep WA L L H O O D S Mounting holes for 27 686 hoods Rough-in plate installationE P 4 I N S TA L L R O U G H I N P L AT E P O RTA N T N OT E PRO Wall V E N T I L AT I O N H O O D SE P 6 I N S TA L L W I R I N G T E R N a L B L O W E R I N S TA L L AT I O N Internal blower installationDimensions for BLOWER-60IL Dimensions for BLOWER-110IL Line a N D Remote B L O W E R SO W E R I N S TA L L AT I O N O W E R W I R I N G Dimensions for BLOWER-90REMDimensions for BLOWER-120REM Dimensions for BLOWER-150REMM OT E B L O W E R S Blower a S S E M B L I E ST E R N a L B L O W E R S L I N E B L O W E R SFilter and grease cup installation Duct cover installationYO U N E E D Service Nameplate I N S TA L L AT I O NRO U B L E S H O O T I N G Page 9 3 4 0 0
Top Page Image Contents