Wolf W302210I P O Rta N T N Ot E, PRO Wall V E N T I L AT I O N H O O D S

Page 16

I M P O RTA N T N OT E

You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service.

W O L F PRO WALL VENTILATION H O O D S

PRO WALL V E N T I L AT I O N H O O D S

S T E P 6 : I N S TA L L W I R I N G

This ventilation hood must be properly grounded. This unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes.

Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on acciden- tally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

Remove the electrical box cover from the rough-in plate. Connect black wire to power supply black wire, white wire to power supply white wire and green wire to green wire or bare wire.

Place all wiring connections inside the elec- trical box and reinstall on the rough-in plate in the upper right-hand corner. Make sure that the wires are secure and that no wires are pinched between the cover and box.

Do not remove the control knob bezel to access hood wiring; this will damage the bezel assembly.

Run a 120 V AC, 15 amp circuit power cable from the service panel to the electrical box in the rough-in plate.

Remove the knockout and install the conduit connector on the rough-in plate hole. Refer to the illustrations below for the wiring location of your specific wall hood.

Insert the conduit through the hole on top of the rough-in plate to the electrical box.

2" (51)

2" (51)

21/2" (64)

 

21/2" (64)

2" (51)

1/2" (64)

21/2" (64)

2

21/2" (64)

 

 

21/2" (64)

 

 

Low-profile hoods wiring location

24" (610) deep hoods wiring location

27" (686) deep hoods wiring location

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Installation Instructions Wolf Customer Service Website Wolfappliance.com N TA C T F O R M AT I O NS TA L L AT I O N R E Q U I R E M E N T S S T O F M AT E R I a L SInstallation C O N S I D E R AT I O N S C E S S O R I E SE C T R I C a L R E Q U I R E M E N T S C T C O V E R6 1 0 D E E P WA L L H O O D S W- P R O F I L E WA L L H O O D S6 8 6 D E E P WA L L H O O D S Low-Profile 24 610 Deep Wall Hoods Installation S P E C I F I C AT I O N S27 686 Deep Wall Hoods 24 610 Deep Wall Hoods Model Low-Profile Wall Hoods Model27 686 Deep Wall Hoods Model To reduce the risk of fire, use only metal ductwork E P 1 I N S TA L L D U C T W O R KDucting options for low-profile wall hoods S TA L L AT I O N I N S T R U C T I O N S Ducting options for 24 610 deep wall hoodsRough-in plate/transition assembly E P 2 WA L L P R E PA R AT I O NE P 3 H O O D P R E PA R AT I O N If wall framing is not available, wall anchors must be usedWall cut-out for low-profile hoods horizontal discharge E P 4 R E AT TA C H R O U G H I N P L AT EWall cut-out for 24 610 deep hoods horizontal discharge E P 5 I N S TA L L T H E H O O D Hood installationM P L E T E T H E I N S TA L L AT I O N 27 686 Deep WA L L H O O D S Rough-in plate installation Mounting holes for 27 686 hoodsE P 4 I N S TA L L R O U G H I N P L AT E PRO Wall V E N T I L AT I O N H O O D S P O RTA N T N OT EE P 6 I N S TA L L W I R I N G Internal blower installation T E R N a L B L O W E R I N S TA L L AT I O NLine a N D Remote B L O W E R S Dimensions for BLOWER-60IL Dimensions for BLOWER-110ILO W E R I N S TA L L AT I O N Dimensions for BLOWER-90REM Dimensions for BLOWER-120REMDimensions for BLOWER-150REM O W E R W I R I N GBlower a S S E M B L I E S T E R N a L B L O W E R SL I N E B L O W E R S M OT E B L O W E R SDuct cover installation Filter and grease cup installationNameplate I N S TA L L AT I O N YO U N E E D ServiceRO U B L E S H O O T I N G Page 9 3 4 0 0
Top Page Image Contents