Wolf W302210I Duct cover installation, Filter and grease cup installation

Page 21

I N S TA L L AT I O N I N S T R U C T I O N S

DUCT COVER I N S TA L L AT I O N

I N S TA L L FILTERS / GREASE CUPS

Installing a duct cover assembly will impact all aspects of the hood installa- tion including hood location, ducting, electrical placement and the mounting surface.

IMPORTANT NOTE: If a duct cover is to be used, follow these instructions before installing the wall hood.

Attach the duct cover from the inside of the hood through the filter opening using the screws provided.

Leave screws partially loose until all screws are installed. Check alignment of the duct cover with the hood and tighten the four corner screws to secure the duct cover. Tighten all remaining screws.

For low-profile and 24" (610) wall hoods follow hood installation instructions on page 8. For 27" (686) wall hoods follow hood installation instructions on page 13.

Duct covers 6" (152) and 12" (305) high in widths to match all wall hoods are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com.

Remove all packaging material from the filters and grease cups.

Slide the grease cups along the bottom edge of the hood so that the lip of the grease cup overhangs slightly.

Install the filters. Orient each filter with lines running vertically. Position the top edge of the filter as shown in the illustra- tion below. While pressing up against the spring, rotate the bottom edge of the filter into position next to the grease cup. Gloves should be worn to provide proper grip.

A C C E S S O R I E S

Optional acces- sories are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com.

Optional

Duct Cover

Mounting

Screws

Duct cover installation

 

Spring

 

Filter

Grease Cup

SIDE VIEW

Filter and grease cup installation

Dimensions in parentheses are in

 

millimeters unless otherwise specified.

21

Image 21
Contents Installation Instructions N TA C T F O R M AT I O N Wolf Customer Service Website Wolfappliance.comS T O F M AT E R I a L S S TA L L AT I O N R E Q U I R E M E N T SC E S S O R I E S Installation C O N S I D E R AT I O N SE C T R I C a L R E Q U I R E M E N T S C T C O V E RW- P R O F I L E WA L L H O O D S 6 1 0 D E E P WA L L H O O D S6 8 6 D E E P WA L L H O O D S Installation S P E C I F I C AT I O N S Low-Profile 24 610 Deep Wall Hoods27 686 Deep Wall Hoods Low-Profile Wall Hoods Model 24 610 Deep Wall Hoods Model27 686 Deep Wall Hoods Model E P 1 I N S TA L L D U C T W O R K To reduce the risk of fire, use only metal ductworkDucting options for low-profile wall hoods Ducting options for 24 610 deep wall hoods S TA L L AT I O N I N S T R U C T I O N SE P 2 WA L L P R E PA R AT I O N Rough-in plate/transition assemblyE P 3 H O O D P R E PA R AT I O N If wall framing is not available, wall anchors must be usedE P 4 R E AT TA C H R O U G H I N P L AT E Wall cut-out for low-profile hoods horizontal dischargeWall cut-out for 24 610 deep hoods horizontal discharge Hood installation E P 5 I N S TA L L T H E H O O DM P L E T E T H E I N S TA L L AT I O N 27 686 Deep WA L L H O O D S Mounting holes for 27 686 hoods Rough-in plate installationE P 4 I N S TA L L R O U G H I N P L AT E P O RTA N T N OT E PRO Wall V E N T I L AT I O N H O O D SE P 6 I N S TA L L W I R I N G T E R N a L B L O W E R I N S TA L L AT I O N Internal blower installationDimensions for BLOWER-60IL Dimensions for BLOWER-110IL Line a N D Remote B L O W E R SO W E R I N S TA L L AT I O N Dimensions for BLOWER-120REM Dimensions for BLOWER-90REMDimensions for BLOWER-150REM O W E R W I R I N GT E R N a L B L O W E R S Blower a S S E M B L I E SL I N E B L O W E R S M OT E B L O W E R SFilter and grease cup installation Duct cover installationYO U N E E D Service Nameplate I N S TA L L AT I O NRO U B L E S H O O T I N G Page 9 3 4 0 0