KitchenAid 2308307 Remove the Door Panels, Replace the Door Panels, Care for Decorator Panels

Remove the Door Panels

NOTE: When removing and replacing decorator panels, only the handle is removed. All other trim pieces remain attached to the doors.

1.Remove the refrigerator and freezer handles:

■Using a Phillips screwdriver, remove the screws that hold each handle in place.

■Lift off handle. Make sure you keep screws for reattaching handles.

2.Remove the door panels:

■Open refrigerator or freezer door.

■Slide out decorator panel and filler board.

■Repeat process for other panels and filler boards.

■Store panel and filler boards to prevent scratching.

Replace the Door Panels

1.Replace the refrigerator or freezer door panels:

■Open refrigerator or freezer door.

■Slide the ¹⁄₈" (3.18 mm) decorator panel into place behind the side trim.

■Push the filler board into place behind the decorator panel.

■Repeat process for other panels and filler boards.

2.Attach the handles:

NOTE: Freezer door handle is notched to fit around the dispenser panel.

■Align the top of the refrigerator or freezer handle flush with the top trim. Fasten the handle to the refrigerator or freezer door with the screws, using a Phillips screwdriver.

■Repeat the process for the other handle.

Care for Decorator Panels

1.Clean panels with an anti-static cleaner (available in electronics or computer departments) or mild soap and water with a clean, soft, damp cloth.

2.Rinse panels thoroughly and blot dry using a dry, soft cloth or chamois.

NOTE: Do not use paper towels or cleaners which contain solvents such as ammonia. They can damage the surface of the panels.

3.If small scratches should appear on the panels, they may be filled using an automotive paste wax (not a cleaner/wax combination). Apply wax sparingly and buff lightly with a clean, soft cloth using a circular motion.

Install Custom Wood Panels

If you plan to install custom wood decorator panels, you will need to create the panels yourself or consult your cabinetmaker or carpenter. See dimensional drawings for wood panel inserts.

Flat panels:

You can create a custom flat panel a maximum of ¹⁄₄" (6.35 mm) thick to replace your decorator panels. Flat wood panels less than ¹⁄₄" (6.35 mm) thick are not recommended.

Raised panels:

A raised panel design can be created by screwing or gluing wood panels to ¹⁄₄" (6.35 mm) backing or by using ³⁄₄" (19.05 mm) stock with routed edges.

Weight requirements for raised panel inserts:

■Refrigerator door panel should not exceed 25 lbs.

(9.98 kg).

■Freezer door panels should not exceed 18 lbs. (6.80 kg) combined weight.

Dimensions for Custom Wood Panels:

22 cu. ft Freezer and Refrigerator door

	1/4"			1/4"
	(6.35 mm)			(6.35 mm)
5/16"					5/16"
(7.93 mm)		185/32"			(7.93 mm)
		(46.1 cm)
	127/16"
	(31.6 cm)
	127/16"	6011/64"
		(154.2 cm)		1915/16"
	(31.6 cm)
			(50.7 cm)
		285/64"
5/16"		(71.3 cm)			5/16"
(7.93 mm)					(7.93 mm)
	1/4"			1/4"
	(6.35 mm)			(6.35 mm)
3/4" min.	31/4"	3/4"	31/4"	3/4" min.	3/4"
(19.05 mm min.) (82.55 mm min.)		(19.05 mm)	(82.55 mm min.)(19.05 mm min.)(19.05 mm)
	TOP VIEW	1/4"		TOP VIEW	1/4"
	(6.35 mm)				(6.35 mm)

10