KitchenAid W10342488A Range Hood Care, Cleaning, Replacing theHalogen Bulb

Page 13

RANGE HOOD CARE

Cleaning

IMPORTANT: Clean the range hood and grease filter frequently according to the following instructions. Replace grease filter before operating range hood.

Be sure light is cool before cleaning the range hood.

Exterior Surfaces

Clean the range hood with a mild detergent and soft cloth. To avoid damage to the exterior surface, do not use abrasive cleansers or steel-wool pads

Metal Grease Filter

The filter should be washed frequently. Place metal filter in dishwasher or hot detergent solution to clean. Let filter dry thoroughly before replacing it.

Turn off fan and lights. Allow the halogen bulbs to cool.

1.Remove the filter by pulling the spring release handle and then pulling down the filter.

To Install Charcoal Filter

1.For non-vented (recirculating installations), fit the charcoal filter on the rear side of the metal grease filter.

2.Secure the charcoal filter in place with the metal brackets supplied.

B C

A

A.Metal brackets

B.Charcoal filter

C.Metal grease filter

3.Reinstall the filter assembly into the range hood.

A

To Replace Charcoal Filter

1.Turn fan and lights off. Check that the halogen bulbs are cool.

2.Remove the metal grease filter. See the “Metal Grease Filter” section.

3.Remove the brackets and remove the charcoal filter.

4.Clean or discard the charcoal filter.

5. Install the cleaned or replacement filter.

A. Spring release handle

2.Wash the metal filter as needed in the dishwasher or hot detergent solution.

3.Reinstall the filter by making sure the spring release handle is toward the front. Insert the metal grease filter into the upper track.

4.Pull the spring release handle down.

5.Push up on the metal filter and release the handle to latch into place.

Replacing theHalogen Bulb

Turn off the range hood and allow the halogen bulbs to cool. To avoid damage or decreasing the life of the new bulb, do not touch the bulb with bare fingers. Replace the bulb using tissue or wearing cotton gloves to handle bulb.

If the new bulbs do not operate, make sure the bulbs are inserted correctly before calling service.

1.Disconnect power.

2.Use a flat-blade screwdriver to gently pry and remove the bulb.

Charcoal Filter - For Non-Vented (recirculating)

Installations

NOTE: After approximately 3 years of use the charcoal filter should be replaced. To order a replacement Charcoal Filter Kit, see the “Assistance or Service” section.

The charcoal filter can be cleaned and reactivated. Clean the filter

in the dishwasher using normal detergent and the highest temperature setting. To reactivate the filter, dry the filter in an

oven for 10 minutes at a maximum temperature of 210°F (100°C). 3. Replace with a 12-volt,20-watt maximum, halogen bulb made for a GU-4 base.

4. Reconnect power.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents SLIDE-OUT Range Hood Table of Contents/Table des matièresTable DES Matières Range Hood SafetyImportant Safety Instructions ToolsandParts Installation RequirementsLocation Requirements Cabinet Dimensions Product DimensionsVentingRequirements For the most efficient and quiet operationMakeup air Cold weather installationsVenting Methods Example vent system 6 15.2 cmElectricalRequirements Installation InstructionsPrepareLocation Range Hood Cabinet CutoutVenting Outside Through the Wall Venting Outside Through the RoofUse caulking to seal around wire opening InstallRange Hood5 x 9.5 mm screws Install 2 5 x 18 mm adjusting screwsNon-Vented recirculating Installations Vented InstallationsElectrical Connection ConnecttheVentSystemControls Display Range Hood USERange Hood Care CleaningReplacing theHalogen Bulb SEL0015013 Wiring DiagramAccessories Assistance or ServiceIntheU.S.A InCanadaThis limited warranty does not cover Kitchenaid Ventilation WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA Hotte D’ASPIRATIONImportantes Instructions DE Sécurité Exigences demplacement Exigences DinstallationOutils et pièces Dimensions du placard Dimensions du produitExigencesconcernant l’évacuation Pour un fonctionnement efficace et silencieuxAir d’appoint Installations pour régions à climat froidMéthodes d’évacuation Calcul de la longueur effective du circuit dévacuationLes instructions suivantes SpécificationsélectriquesConnecter une section de câble en cuivre massif aux Conducteurs en queue de cochonPréparationdelemplacement Instructions D’INSTALLATIONOuverture découpée du placard pour la hotte Décharge à lextérieur, à travers le toitDécharge à lextérieur, à travers le mur Vis de montage de 3,5 x 9,5 mm Installationde lahotteRaccordementélectrique Installer 2 vis de réglage de 5 x 18 mmInstallation sans décharge à l’extérieur recyclage Installations avec décharge à l’extérieurRaccordement du circuit dévacuation Utilisation DE LA Hotte Dispositifs decommandeAffichage Entretien DE LA Hotte Remplacement delampoule àhalogèneNettoyage Interface utilisateur Schémas DE CâblageAccessoires Assistance OU ServiceAuCanada La présente garantie limitée ne couvre pas Garantie DU Système DE Ventilation KitchenaidComposer le 1-800-422-1230. Au Canada, composer le W10342488A

W10342488A specifications

The KitchenAid W10342488A is a versatile and efficient appliance accessory designed to elevate your cooking experience in the kitchen. Compatible with various KitchenAid stand mixers, this attachment serves as a powerful helper for both novice cooks and seasoned chefs.

One of the standout features of the W10342488A is its robust construction. Made from high-quality materials, it ensures durability and longevity, allowing users to perform a wide range of culinary tasks without worrying about wear and tear. The attachment boasts a sleek and modern design that seamlessly integrates with the aesthetic of KitchenAid stand mixers, enhancing their overall appeal.

Equipped with a powerful motor, this attachment delivers consistent performance whether you’re mixing dough, whipping cream, or preparing batters. Its efficiency allows for faster meal preparation, making it a valuable addition to any kitchen. The bowl lift design ensures stability during operation, enabling users to mix even the heaviest ingredients with ease.

Another key aspect of the W10342488A is its user-friendly interface. Featuring intuitive controls, it simplifies the mixing process, allowing users to adjust speeds according to their needs. The attachment also includes various speed settings, providing flexibility for different recipes and textures. Whether you want to create a fluffy meringue or a dense bread dough, the W10342488A has you covered.

Moreover, the attachment incorporates advanced mixing technology that allows for the even distribution of ingredients. This ensures that your recipes turn out perfectly every time, enhancing the quality of your culinary creations. The design also promotes easy cleaning, with some components being dishwasher safe, contributing to a hassle-free cooking experience.

In addition to its practical features, the KitchenAid W10342488A is backed by the brand's reputation for innovation and quality. KitchenAid is known for producing reliable kitchen appliances that inspire creativity and efficiency in cooking. With the W10342488A, users are equipped to explore new recipes and culinary techniques, making it an essential tool for enhancing the home cooking experience.

In conclusion, the KitchenAid W10342488A attachment stands out for its durability, efficiency, and user-friendly design. Featuring advanced technology and versatile capabilities, this appliance is perfect for anyone looking to elevate their culinary skills while enjoying the time-saving benefits of a KitchenAid mixer.
Top Page Image Contents