KitchenAid W10342488A Installation Requirements, ToolsandParts, Location Requirements

Page 4

INSTALLATION REQUIREMENTS

ToolsandParts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Level

Drill

¹⁄₈" (3 mm) drill bit

³⁄₄" (19 mm) drill bit

Pencil

Pliers

Wire stripper or utility knife

Tape measure or ruler

Caulking gun and weatherproof caulking compound

Phillips screwdriver

Flat-blade screwdriver

T-10 TORX®† driver

Saber or keyhole saw

Vent clamps

Metal snips

Parts needed

Home power supply cable

Two ¹⁄₂" (1.3 cm) UL listed or CSA approved strain reliefs

3 UL listed wire connectors

For vented installations, you will also needed:

1 wall or roof cap

Metal vent system

For non-vented (recirculating) installations, you will also need:

Recirculation Kit Part Number W10356918. See the “Assistance or Service” section to order.

Optional parts needed:

Wood filler strips for cabinets with recessed bottoms. Length and thickness determined by recess dimensions. See the “Prepare Location” section.

Two, 1" x 1" x 5" (25 x 25 x 12.7 cm) wood pieces for cabinet floor. See the “Prepare Location” section.

Four, 1¹⁄₄" (3.2 cm) wood screws

Parts supplied

Remove parts from packages. Check that all parts are included.

Damper: Part Number W10369162

Hardware package: Part Number W10369160. Includes: Installation Instructions and Use and Care Guide

2 lower leveling brackets

2 upper leveling brackets

2 - 2.5 x 9.5 mm metal screws

4 - 4.5 x 16 mm wood screws

4 - 5 x 18 mm machine screws

4 - 3.5 x 9.5 mm metal screws

†®TORX is a registered trademark of Saturn Fasteners, Inc.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the filter on the left rear wall of the range hood.

Range hood location should be away from strong draft areas, such as windows, doors, and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Consult your cooktop/ range manufacturer installation instructions before making any cutouts.

Grounded electrical outlet is required. See “Electrical Requirements” section.

The range hood is factory set for vented installations through the roof or wall. For non-vented (recirculating) installations see “Non- Vented (recirculating) Installation Through the Soffit/Cabinet” in the “Prepare Location” section. Recirculation Kit Part Number W10356918 is available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where range hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes.

4

Image 4
Contents Table of Contents/Table des matières SLIDE-OUT Range HoodRange Hood Safety Table DES MatièresImportant Safety Instructions ToolsandParts Installation RequirementsLocation Requirements Product Dimensions Cabinet DimensionsVentingRequirements For the most efficient and quiet operationCold weather installations Makeup airVenting Methods Example vent system 6 15.2 cmInstallation Instructions ElectricalRequirementsPrepareLocation Range Hood Cabinet CutoutVenting Outside Through the Roof Venting Outside Through the WallInstallRange Hood Use caulking to seal around wire openingInstall 2 5 x 18 mm adjusting screws 5 x 9.5 mm screwsVented Installations Non-Vented recirculating InstallationsElectrical Connection ConnecttheVentSystemRange Hood USE Controls DisplayRange Hood Care CleaningReplacing theHalogen Bulb Wiring Diagram SEL0015013Assistance or Service AccessoriesIntheU.S.A InCanadaKitchenaid Ventilation Warranty This limited warranty does not coverSécurité DE LA Hotte D’ASPIRATION Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Exigences demplacement Exigences DinstallationOutils et pièces Dimensions du produit Dimensions du placardExigencesconcernant l’évacuation Pour un fonctionnement efficace et silencieuxInstallations pour régions à climat froid Air d’appointMéthodes d’évacuation Calcul de la longueur effective du circuit dévacuationSpécificationsélectriques Les instructions suivantesConnecter une section de câble en cuivre massif aux Conducteurs en queue de cochonInstructions D’INSTALLATION PréparationdelemplacementOuverture découpée du placard pour la hotte Décharge à lextérieur, à travers le toitDécharge à lextérieur, à travers le mur Installationde lahotte Vis de montage de 3,5 x 9,5 mmInstaller 2 vis de réglage de 5 x 18 mm RaccordementélectriqueInstallation sans décharge à l’extérieur recyclage Installations avec décharge à l’extérieurRaccordement du circuit dévacuation Utilisation DE LA Hotte Dispositifs decommandeAffichage Entretien DE LA Hotte Remplacement delampoule àhalogèneNettoyage Schémas DE Câblage Interface utilisateurAccessoires Assistance OU ServiceAuCanada Garantie DU Système DE Ventilation Kitchenaid La présente garantie limitée ne couvre pasComposer le 1-800-422-1230. Au Canada, composer le W10342488A

W10342488A specifications

The KitchenAid W10342488A is a versatile and efficient appliance accessory designed to elevate your cooking experience in the kitchen. Compatible with various KitchenAid stand mixers, this attachment serves as a powerful helper for both novice cooks and seasoned chefs.

One of the standout features of the W10342488A is its robust construction. Made from high-quality materials, it ensures durability and longevity, allowing users to perform a wide range of culinary tasks without worrying about wear and tear. The attachment boasts a sleek and modern design that seamlessly integrates with the aesthetic of KitchenAid stand mixers, enhancing their overall appeal.

Equipped with a powerful motor, this attachment delivers consistent performance whether you’re mixing dough, whipping cream, or preparing batters. Its efficiency allows for faster meal preparation, making it a valuable addition to any kitchen. The bowl lift design ensures stability during operation, enabling users to mix even the heaviest ingredients with ease.

Another key aspect of the W10342488A is its user-friendly interface. Featuring intuitive controls, it simplifies the mixing process, allowing users to adjust speeds according to their needs. The attachment also includes various speed settings, providing flexibility for different recipes and textures. Whether you want to create a fluffy meringue or a dense bread dough, the W10342488A has you covered.

Moreover, the attachment incorporates advanced mixing technology that allows for the even distribution of ingredients. This ensures that your recipes turn out perfectly every time, enhancing the quality of your culinary creations. The design also promotes easy cleaning, with some components being dishwasher safe, contributing to a hassle-free cooking experience.

In addition to its practical features, the KitchenAid W10342488A is backed by the brand's reputation for innovation and quality. KitchenAid is known for producing reliable kitchen appliances that inspire creativity and efficiency in cooking. With the W10342488A, users are equipped to explore new recipes and culinary techniques, making it an essential tool for enhancing the home cooking experience.

In conclusion, the KitchenAid W10342488A attachment stands out for its durability, efficiency, and user-friendly design. Featuring advanced technology and versatile capabilities, this appliance is perfect for anyone looking to elevate their culinary skills while enjoying the time-saving benefits of a KitchenAid mixer.