KitchenAid W10342488A InstallRange Hood, Use caulking to seal around wire opening

Page 9

For non-vented (recirculating) installations, charcoal filters are necessary. See the “Range Hood Care” section for instructions on installing charcoal filters.

The Recirculation Kit Part Number W10356918 must be used.

6.Install the vent system according to the method needed. Use caulking to seal the exterior wall or roof opening.

7.Run the wiring through the wall or cabinet according to the national Electrical Code and all local codes and ordinances.

Use caulking to seal around wire opening.

8.Measure the thickness of the cabinet floor, including the filler strips, if used. If the thickness is less than ³⁄₄" (1.9 cm), install wood filler strips that are a minimum length of 5" (12.7 cm) onto the cabinet floor. The mounting bracket adjusts from ³⁄₄" (1.9 cm) to 1¹⁄₂" (3.8 cm) for the wood filler strips.

A

B

A. Less than ¹⁄₂" (12.7 mm)

B. Wood fillers (thickness as required)

9.The spring loaded brackets are factory set to accommodate a thickness of 1" (2.5 cm). The brackets can be adjusted up for thicker cabinets (or down for thinner cabinets) by turning T10 TORX® screw on each side of the hood.

A

A. T10 TORX® screw

10.Place the round damper into the vent opening of the range hood and attach with 2 - 9 x 9.5 mm TORX® screws.

A

B

A.Damper

B.Range hood screen

NOTE: For some non-vented (recirculating) installations it may be easier to attach the vent system to the range hood before lifting the range hood into its final location. Seal the connection with clamps.

InstallRange Hood

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

1.Using 2 or more people, lift the range hood into its final location. (The wiring and terminal box are to be on top of the range hood.)

2.Check that the mounting brackets overlap the cabinet bottom or wood filler strips.

3.Center the range hood.

A

B

C

D

E

A. Mounting bracket

B. Optional wood filler strip

C. Cabinet bottom

D. Optional wood filler strip for recessed cabinet

E. Slide-out range hood

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents SLIDE-OUT Range Hood Table of Contents/Table des matièresTable DES Matières Range Hood SafetyImportant Safety Instructions Installation Requirements ToolsandPartsLocation Requirements Cabinet Dimensions Product DimensionsVentingRequirements For the most efficient and quiet operationMakeup air Cold weather installationsVenting Methods Example vent system 6 15.2 cmElectricalRequirements Installation InstructionsPrepareLocation Range Hood Cabinet CutoutVenting Outside Through the Wall Venting Outside Through the RoofUse caulking to seal around wire opening InstallRange Hood5 x 9.5 mm screws Install 2 5 x 18 mm adjusting screwsNon-Vented recirculating Installations Vented InstallationsElectrical Connection ConnecttheVentSystemControls Display Range Hood USECleaning Range Hood CareReplacing theHalogen Bulb SEL0015013 Wiring DiagramAccessories Assistance or ServiceIntheU.S.A InCanadaThis limited warranty does not cover Kitchenaid Ventilation WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA Hotte D’ASPIRATIONImportantes Instructions DE Sécurité Exigences Dinstallation Exigences demplacementOutils et pièces Dimensions du placard Dimensions du produitExigencesconcernant l’évacuation Pour un fonctionnement efficace et silencieuxAir d’appoint Installations pour régions à climat froidMéthodes d’évacuation Calcul de la longueur effective du circuit dévacuationLes instructions suivantes SpécificationsélectriquesConnecter une section de câble en cuivre massif aux Conducteurs en queue de cochonPréparationdelemplacement Instructions D’INSTALLATIONOuverture découpée du placard pour la hotte Décharge à lextérieur, à travers le toitDécharge à lextérieur, à travers le mur Vis de montage de 3,5 x 9,5 mm Installationde lahotteRaccordementélectrique Installer 2 vis de réglage de 5 x 18 mmInstallations avec décharge à l’extérieur Installation sans décharge à l’extérieur recyclageRaccordement du circuit dévacuation Dispositifs decommande Utilisation DE LA HotteAffichage Remplacement delampoule àhalogène Entretien DE LA HotteNettoyage Interface utilisateur Schémas DE CâblageAssistance OU Service AccessoiresAuCanada La présente garantie limitée ne couvre pas Garantie DU Système DE Ventilation KitchenaidComposer le 1-800-422-1230. Au Canada, composer le W10342488A

W10342488A specifications

The KitchenAid W10342488A is a versatile and efficient appliance accessory designed to elevate your cooking experience in the kitchen. Compatible with various KitchenAid stand mixers, this attachment serves as a powerful helper for both novice cooks and seasoned chefs.

One of the standout features of the W10342488A is its robust construction. Made from high-quality materials, it ensures durability and longevity, allowing users to perform a wide range of culinary tasks without worrying about wear and tear. The attachment boasts a sleek and modern design that seamlessly integrates with the aesthetic of KitchenAid stand mixers, enhancing their overall appeal.

Equipped with a powerful motor, this attachment delivers consistent performance whether you’re mixing dough, whipping cream, or preparing batters. Its efficiency allows for faster meal preparation, making it a valuable addition to any kitchen. The bowl lift design ensures stability during operation, enabling users to mix even the heaviest ingredients with ease.

Another key aspect of the W10342488A is its user-friendly interface. Featuring intuitive controls, it simplifies the mixing process, allowing users to adjust speeds according to their needs. The attachment also includes various speed settings, providing flexibility for different recipes and textures. Whether you want to create a fluffy meringue or a dense bread dough, the W10342488A has you covered.

Moreover, the attachment incorporates advanced mixing technology that allows for the even distribution of ingredients. This ensures that your recipes turn out perfectly every time, enhancing the quality of your culinary creations. The design also promotes easy cleaning, with some components being dishwasher safe, contributing to a hassle-free cooking experience.

In addition to its practical features, the KitchenAid W10342488A is backed by the brand's reputation for innovation and quality. KitchenAid is known for producing reliable kitchen appliances that inspire creativity and efficiency in cooking. With the W10342488A, users are equipped to explore new recipes and culinary techniques, making it an essential tool for enhancing the home cooking experience.

In conclusion, the KitchenAid W10342488A attachment stands out for its durability, efficiency, and user-friendly design. Featuring advanced technology and versatile capabilities, this appliance is perfect for anyone looking to elevate their culinary skills while enjoying the time-saving benefits of a KitchenAid mixer.
Top Page Image Contents